ARMY MIL-P-11329 E-1983 PRIMER ELECTRIC M59 PARTS FOR AND LOADING ASSEMBLING AND PACKING《M59式电引物用零件及其装药 组装和包装》.pdf

1、NIL-P-l1329E( AR) 11 April 1983 SUPERSEDING MIL -P- 1 1 3 2 9D ( PA) 18 October 1974 MILITARY SPECIFICATION PRIAER, ELECTRIC, M59, PARTS POR AND LOADING , ASSEMBLING AND PACKING This specificaton is approved for use by the US Army Armament Research and Development Command, and is availsble for use b

2、y all Deprtments and Agencies of the Department of Defense. 1. -SCOPE 1.1 This specification covers the parts fort loading, assembling and packing for one type of primer , designated as Primer, Electric, M59, for use in Photoflash Cartridges. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 S

3、pecification and standards. Unless otherwise specified (see 6.2), the following specification and standards of the issue listed in that issue of the Department of Defense Index of Specifi- cations and Standards (DoDISS) specified in the solicitation, form a part of this specification to the extent s

4、pecified herein. SPECIFICATIONS MIL ITARY MIL-I?-116 MIL-A-4 80 78 - Preservation - Packaging, Nethod Of - Ammuni tion, Standard Quality Assurance Provisions General Specification For STANDARDS MILITARY XIL-STD- 105 - Sampling Procedures and Tables for MIL-STD-1168 - Lot Numbering of Ammunition MIL-

5、STD-1169 - Packaging, Packing, and Harking for Inspection by Attributes Chipent of Inert Ammuni tion Components 1390 Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improvin this document should be addressed to: Commander, US Army Armament te

6、esearch and Develo ment Command, Attn. DRDAR-QA, Dover, New Jersey 07801 by using te self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

7、om IHS-,-,-2.1.2 Other Government documents, drawings, and publications. - The. followins other Government documents, drawinqs, and publications form a part of this specification to the extent Specified herein. DRAWINGS US ARMY ARMAMENT RESEARCH AND CEVELOPMENT COMMAND (ARRADCOM) 8848644 - Primer, E

8、lectric, M59, Assembly 8853703 - Boxes, Set-up, Packing Ammunition, Inner and Outer, for Primer Electric, M59 Assembly, Details and Packing and Marking Electric, M59, Assembly Details and Packing 8853702 - Box, Packing Ammunition, for Primer, 9226356 - Primer, Electric, M59, Parts Arrangement (Copie

9、s of specifications, standards, handbooks, drawings, and publications required by manufacturers in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting officer). In the event of a conflict between the text of this specifica

10、tion and the references cited herein, the text of this specification shall take precedence. 2.1.3 Order of precedence. - 3. REQUIREMENTS 3.1 Material Materials and parts shall be in accordance with applicable drawings, specifications and standards. 3.2 Parts. The parts shall comply with all requirem

11、ents specified on drawing (dwg. 9226356), and with all requirements specified in applicable specifications. 3.3 Assembly. The primers shall comply with all requirements specified on drawing (dwg.) 8848644, and with all requirements specified in applicable specifications. 3.4 Moisture content of igni

12、ter mixture. The moisture content of the igniting mixture, at the time of loading, shall not exceed 0.30 percent. 3.5 Functioning. 3.5.1 All-Fire. The primer assembly shall fire when a 1.8 ampere maximum(max.) current is applied to the electrode. ampere minimn) current is applied to the electrode. 3

13、.5.2 No-Fire. The primer assembly shall not fire when a 0.70 2 /- - 7, I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-P-LL329E L3 7777906 0273514 5 m MIL-P-11329E( AR) 3.6 First Article Inspection. This specification contains technics1 provis

14、ions for first article inspection. the submission OE first article samples by the contractor shall be as specified in the contract. be fabricated and loaded in a thorough workmanlike manner , and al1 manufacturing corrzctly performed. They shall be clean and free of burrs, sharp edges, unblended rad

15、ii, surface defects, chips, dirt, grease and oil (excspt where specifically required) , corrosion products and other foreign matter. The cleaning method used shall not be injurious to any part or assembly nor shall they be contaminated by the cleaning agent. Exterior surfaces matings shall be contin

16、uous except for a few light scratches not exposing base material. markings shall be neat and sharply defined. be dry) Requirements for 3.7 Workmanship (M eta1 Parts). All parts and assemblies shall processing , and assembly operations shall be All required (Required packing shall 3.8 Workmanship (Pl

17、astic hrts). All parts and assemblies shall be f3bricated and finished in a thorough workmanlike manner and all manuacturing, processing and assembly operations shall be correctly performed. They shall be free of burrs, chips, sharp edges , cracks r crazes I unblended radii , porosity, warpage, burn

18、 marks , checks , chipped edges , blisters , excess flash, dirt , grease , rust, salt deposits, visible raised cenent seams, solder splash, corrosion products, and other defects and foreign matter which would affect their serviceability. The cleaning method used shall not be injurious to any part or

19、 assembly nor shall the parts be contaminated by the cleaning agent. All required markings shall be neat, legible and sharply defined. 4, QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection and standard quality assurance provisions. Unless otherwise specified herein or in the contrqct, th

20、e provisions of MIL-A-48078 shall apply and are hereby made a prt of this detail specifiation. 4.2 Classification of inspections. The following types of inspction shall ix conducted on this item. a . First Article Inspection b. Quality Conformance Inspection 4.3 First article inspection 4.3.1 Submis

21、sion. The contractor shall submit a first article sample as designated by the Contracting Officer. The first article sample shall consist of twenty-five (25) complete sets of prts and subassemblies (i .e ., 25 each of every canponent and subassembly 3 Provided by IHSNot for ResaleNo reproduction or

22、networking permitted without license from IHS-,-,-MIL-P-11329E 13 m 9979906 0293575 7 m li MIL-P-l1329E(AR) including at least five (5) items frm each cavity used to produce molded prts and be so identified as to permit; tracing each item to the cavity in which it was molded) and three hundred (300)

23、 camplete primer assemblies. The first article shall be evalmted in accordance with the provisions of 4.3.2 and 4.3.3. spaciied herein . 4.3.2 Inspections to be performed. See MIL-A-48078 and Table I 4.3.3 Rejection. See MIL-A-480 78 . 4 Provided by IHSNot for ResaleNo reproduction or networking per

24、mitted without license from IHS-,-,-8 t rl iii“ MIL-P-lt1329E 13 999990b 0293576 7 E 1 - u) cy a a O c, rlrl (um *a aa . * .* IL cy . . -a a O 4 o cv * a . . 4 rl cy a a . * O ci. cy- M mm m * * cy4 mu) m MM M o* * . dro O O 4 R O00 0u)m O au A m O cv u) Mrlrl u) v u) c, U a, w a, tl k O w c O -rl c

25、i Id c la Id x w *ri a, u c Id ci u) -ri n u)* a,* ffia a3 0. dRU i i - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-1329E (AR) 4.4 Quality Conformance Inspection 4.4.1 Inspection Lot; Formation. See MIL-A-48078. Lot numbering as required sh

26、all be in accordance with MIL-STD-1168. addition, inspection lots pf Primer Assemblies shall contain. In a. b. Parts of one lot interfix number from one manufacturer. Igniter mixture from one batch or blending of batches which results in homogeneity of all igniter mixture used in loading the entire

27、primer lot. specified in the Classification of Defects and Test Tables, sampling plans for major and minor defects shall be in accordance with MIL-STD-105, Inspection Level II. performance of the inspections shall be in accordance with 4.4.4. 4.4.2 Examination. See MIL-A-48078. Unless otherwise Equi

28、pment necessary for the 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-a, 5 O Ll +I o a, rl fil rl (v cy d( . - a, dPdPdPdpdPdP O mmmmmo * wwwu)wo O 00000,l e. u dl o Provided by IHSNot for ResaleNo reproduction or networking permitted without lic

29、ense from IHS-,-,-w 4 w QI cv m rl rl I pi I c CI 2 2 o rl 8 t rl m c rPG - c MIL-P-LL327E L3 777770b 0273577 Li rl CVcvcvNr- N M MMMMM w *.*e U a, c I4 CI a, U a, C O z 0- LI 1 -II Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4 I -lK MIL-P-11327E

30、 13 9797706 0293580 O U dP owdo O U30 d 90 O O4 a a. ci a, wo oc a, !i i3 aa Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-z I3 u w PI VJ H Ei 8 i O O 3 Er z 8 H 3i rl L O rl ti M w -_ _I_ _-I_ MIL-P-33329E 33 W 9999706 0293583 2 W t *. O w 5 U N N

31、b a 88 m mM a a, C .d w a, 5 a, C O z a a a, rc ci c 4J 4 3 a, a O u ci o a, rl a, w O h ci .rl o .I4 u ci c a, o u LI 8 rll 6 % I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-11329E 13 9999906 0293582 4 rl 8 t rl w h rl n cn cn 4 a, o O M 3

32、 o a, rl w o C (d 3.( 5 d rS - - ilNb mmm * 5 a, c .Pl w a, 5 a, C O z Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-P-ll327E 131 7777906 0273583 b M ri 8 ri t # !? i Q) VI d H O U 8 -li k pi . ri k ii w O 0 U a 8 I Provided by IHSNot for Resa

33、leNo reproduction or networking permitted without license from IHS-,-,-rl MIL-P-LL327E 13 7777906 0273584 8 4 O O8 O kX w O y . a, u 1 13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-n 2 W w ci CJ m rl rl 1 pi I H r a t - MIL-P-LL327E 13 7777%b 02

34、73585 T-I I li t5 tl rl a /- 7 rn 14 /- - - . i I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2; I3 u w pi VI E w w O f 2 O u k I3 P 0, rl Lr O rl t a 8 d u pi 4 u a, 4J 3 O u aJ C c n al cv -P -P e w - rl rld rlrl m mm mr- e e. m mm me; u aJ C *

35、d rn aJ *d rl 1) (II rn m u-l O u Cu 9 a Qi z 3 o aJ Li ux C H 89 a 4 E (II i O u * k H 2 8 m E? 3,: am E, 8 8 8 88 O0 o 00Qrl 3a,30 ad E s2-4 a, c 4Jrl 3 a, o c-4 a, a.4 cx c, cum ia- h rl u ha, ria +JO ou u 4 O u2 o , Provided by IHSNot for ResaleNo reproduction or networking permitted without lic

36、ense from IHS-,-,- - MIL-P-l3329E 13 999990b 0293593 5 4.4.3 Testing 4.4.3.1 Moisture content of igniter mixture (see 3.4) - Major defect. The contractor shall provide adequate cgntrols to insure compliance with the requiremenis, and shall test; for verifiatiqn at least one sample of igniter mixture

37、 frop eich eight (8) hours production of primer assembJ.ies. CQmposite samples shall not be used. and loading has not begunr th9 qqantjty pf niatwiql roRFsqenCed by the sample shall be rejected, IS asps?l$q have been lagde($ with with the non-conforming material shall be xejectefl. be performed as s

38、pecified in 4.5.1. If the moisture conter$ Qf a samplg exvapdq tpe requirement, material containing excessive moi turg, $he redhining mjttsrial that is represented by the sample toge her with all. qssqnblies loaded The keet; shqJ1 4.4.3.2 Functioning 4.4.3.2.1 All-Fire - (see 3,5.1). 4.4.3.2.1.1 Fir

39、st three lots, Begipning yth the first; lot produced and continuing until th3ee (3) consecutjva $ots have complied with the acceptance criteria specified, two hundred (200), primer assemblies shall be selected from each Jpt for tbifit test The lot shall be rejected if three (3) or more Rrimer assemb

40、lies fail to comply with the requirement. specified in 4.5.2.1 using test equipment spGcified in 4.4,41. have complied Ath the crltefiq O 4.4.3.2,J.i eighty (80) primer assemblies shall be selected from each lqt for khi$ test. The lot shall be rejected if two (2) or more primer aesginbligs fqil t9 c

41、omply with the requirement. The test shall be p.grforrned as specified in 4.5.2.1 using test equipment specified in 4.4.4. The teqf! shqLl be performed as 4.4.3.2.1.2 After three lops. After three consecutive lots 4.4.3.2.2 No-Fire (see 3.L.2). 4.4.3.2.2.1 First three lots, Beginning with the girst

42、lot produced and continuing until three (3) coqselutive lots have complied with the acceptance criteria Spec$iedr twa huqqred (200) primer assemblies shall be selecte from each lot for this test. The lot shall be rejected if one or mQre prime7 gssemblies fails to comply with the requirement, The tes

43、t sha1;L be perfqrmd $9. specified in 4.5.2.2 using test equipmqnt sp3cified fn 4.4.4. have complied with the criteria 05 4.4.3.2,2,1 eighty (8Q) pqirner assemblies shall be selected from each lot fcrr this tegt, The lot shall be rejected if one or more primer assemblies fails Co Comply with the req

44、uirement. The test shall be performed as spqcified in 4.5.2.2 using test equipment specified in 4,4.4. 4.4.3.2.2.2 After three lots. After three,copsecutiue lote 20 I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-lL329E 13 H 979790b 0273572

45、7 - MIL-P-1132 9E( AR) 4.4.3.3 Electrical resistance (see dwg. 8848644) - This test shall be conducted 100 percentxy primer which fails to comply with the applicable requirement shall be classed defective and removed from the lot. The test shall be performed as specified in 4.5.3 using equipment in

46、accordance with 4.4.4. 4.4.3.4 Resistance of filament (see dwg. 8848638 covering a detail of dwg. 9226356) - Each roll of wire shall be tested before using. If any roll fails to meet the requirement it shall be classed defective and shall not be used or manufacturing filaments covered by this specif

47、ication. The test shall be performed as specified in 4.5.4. 4.4.3.5 Heat seal test of sealed barrier ba_g (see dwg. 8853703) - Sampling, acceptance criteria and test procedures for this test shall be as specified in MIL-P-116. (Destructive test). 4.4.4 Inspection Equipment. I_ The inspection equipme

48、nt required to perform the inspections and tests prescribed in this specifi- cation is identified in the Paragraph Ref erence/Inspection Method column in the tables starting with paragraph 4.4.2.1, and the test method paragraphs (see 4.4). The contractor shall submit for approval, inspection equipment designs in accordance with the terms of the contract. See Section 6 of MIL-A-48078, and section 6.2 herein. 4.4.5 Dimensional control of molded parts. In place of normal sampling and inspe