ARMY MIL-P-130 F-1985 PAPER WRAPPING LAMINATED AND CREPED《层压包装纸和皱纹包装纸》.pdf

1、MIL-P-130F 30 September 1985 SUPERSEDING MIL-P-130E 3 February 1978 . MILITARY SPECIFICATION PAPER, WRAPPING, LAMINATED AND CREPED This specification isapproved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 11 Scope. This document covers creped wrapping paper, lamina

2、ted or treated if necessary, for use as a protective cover or wrapper. 1.2 Classification. Wrapping paper shall be furnished in rolls of the following types as specified (see 6.2): Type I - Heavy duty Type II - Medium duty Type III - Light duty 20 APPLICABLE DOCUMENTS 2.1 Government documents. Unles

3、s otherwise specified, the following documents of the issue in effect on date of invitation for bids or request for proposal form a part of this document to the extent specified herein. Beneficial comments (recommendations, additions, deletions) and any pertinent data that may be of use in improving

4、 this document should be addressed to U.S. Army Natick Research and Development Center, Natick, MA 01760-5014, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. FSC 8135 DISTRIBUTION STATEMENT A. Approved for

5、public release; distribution is unlimited. ?HIS DOCUMENT CONTAINS . fi- PAGES b. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-130F SPECIFICATIONS FEDERAL “-A-2 60 PPP-B-601 PPP-B-636 PPP-B-1055 PPP-D-723 PPP-T-45 PPP-T-60 PPP-T-7 6 MILITARY

6、MIL-B-1 2 1 MIL-P-130 MIL-L-10547 STANDARDS FEDERAL FED-STD-101 MILITARY MIL-STD-105 MIL-STD-129 MIL-STD-147 . .- Adhesive, Water-Resistant (for Sealing Waterproofed - Boxes, Wood, Cleated-Plywood - Boxes, Shipping, Fiberboard - Barrier Material, Waterproofed, Flexible - Drums, Fiber - Tape, Gummed,

7、 Paper, Reinforced and Plain, for - Tape: Packaging, Waterproof - Tape, Packaging, Paper (For Carton Sealing) Paper) Sealing and Securing - Barrier Material, Grease Proofed, Water Proofed, - Identification Marking of US Military Products - Liners, Case and Sheet, Overwrap, Water-Vaporproof or Flexib

8、le Waterproof, Flexible - Test Procedures for Packaging Materials - Sampling Procedures and Tables for Inspection by - Marking for Shipment and Storage - Palletized Unit Loads Attributes (Copies of documents required by manufacturers in connection with specific acquisition functions should be obtain

9、ed from the contracting activity or as directed by the contracting officer.) * 2.2 Other publications. Unless otherwise specified, the following documents of the issue in effect on date of invitation for bids or request for proposal form a part of this document to the extent specified herein. 2 Prov

10、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. MIL-P-130F / TECHNICAL ASSOCIATION OF THE PULP AND PAPER INDUSTRY (TAPPI) T 402 Standard Conditioning and Testing Atmosphere for Paper, T-403 Bursting Strength of Paper T 404 Tensile Breaking Strength and

11、 Elongation of Paper and Paperboard (Using Pendulum Type Tester) T 410 Grammage of Paper and Paperboard (Weight per Unit Area) T 414 Internal Tearing Resistance of Paper T 428 Hot Water Extractable Acidity or Alkalinity of Paper Board, Pulp Handsheets, and Related Products (Application for copies sh

12、ould be addressed to the Technical Association of the Pulp and Paper Industry, 1 Dunwoody Park, Atlanta, GA 30341.) AMERICAN SOCIETY FOR TESTING AND MATERIALS (AS“) D 3951 - Standard Practice for Commercial Packaging (Application for copies should be addressed to the American Society for Testing and

13、 Materials, 1916 Race Street, Philadelphia, PA 19103.) (Technical society and technical association documents are generally available for reference from libraries. They are also distributed among technical groups and using Federal agencies.) 2.3 Order of precedence. In the event of conflict between

14、the text of this document and the references cited herein, the text of this document shall take precedence. 3. REQUIREMENTS 3.1 Material. The wrapping material shall be made from paper and such nonbituminous laminating or treating materials to ensure compliance with the requirements of this document

15、 Recycled material may be used (see 6.4). 3.2 Physical properties. The finished material shall conform to the applicable physical properties specified in table I when tested as specified in 4.3. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-

16、P-130F 81 m 9999906 0278988 L W MIL-P-130F TABLE I. Physical DroDerties Characteristic Requirement Type 1 Type II Type III Basis weight (24 x 36-500) 150 creped, minimum, in pounds Stiffness, most flexible 200 direction, maximum, in grams Tearing resistance, weakest 250 direction, minimum, in grams

17、Tensile strength, one-way 30 creped only, in weakest direction, minimum, in pounds per inch Bursting strength, two-way 40 creped only, minimum, in p.s.i. 125 100 200 25 35 1 O0 50 150 20 30 3.3 Acid content. The water soluble acidity of the finished material shall be not more than 0.02 percent (calc

18、ulated as sulfur trioxide, Sog), when tested as specified in 4.3. 3.4 Blocking. Finished material, when tested as specified in 4.3, shall not adhere to itself, causing tearing or surface damage. 3.5 Creping. The wrapping paper shall be creped either one-way or two-way. The finished material, when ma

19、de from one-way creped material, shall have a minimum stretch of 20 percent in one direction; for two-way creped material, the stretch in either direction shall be not less than 15 percent when tested as specified in 4.3. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without

20、 license from IHS-,-,-. e O O MIL-P-130F 3.6 Size and roll construction. Wrapping paper shall be furnished in rolls of the length and width specified (see 6.2). Rolls shall be wound uniformly and smoothly on nonreturnable cores of 3-inch inside diameter with a plus 1/8-inch tolerance. The core lengt

21、h shall be not less than the specified roll width nor greater by more than 1/4 inch. Cores shall be fitted with a plug at each end having a 1-inch diameter center hole having plus 1/4-inch tolerance. Rolls shall be suitably restrained to prevent unwinding. 3.6.1 Roll tolerance. 3.6.1.1 Width. A plus

22、 1/8-inch and a minus 1/16-inch tolerance shall be permitted when the paper is creped in the cross direction and a plus or minus 1/8-inch tolerance shall be allowed when creping is in the machine direction or in both directions. 3 . 6.1.2 Length. The length of any individual roll shall be not less t

23、han 95 percent of the specified length. The average length of rolls in any one lot shall be not less than specified length. 3.6.2 Splices. Splices shall cover the entire roll width. Splices shall not separate during unwinding of the roll. No roll shall have more than one splice in any 50-yard length

24、 of the material. Each splice shall be tagged with a colored marker. 3.7 Identification. Wrapping paper shall be marked by printing the applicable document symbols (MIL-P-130), the applicable type (I, II, or III), and the year and month of manufacture at least once in each 3 feet of length and at le

25、ast once in each 18 inches of roll width. 3.8 Workmanship. The wrapping paper shall be clean and free from wrinkles, folds, tears, holes, cuts, abrasions, foreign matter, oil spots, and surface dirt. and dust, Edges shall be clean cut. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspectio

26、n. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for

27、the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set.forth in the document-where such inspections are deemed necessary to ensure that supplies and services conform to prescribed

28、requirements 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-130F 4.2 Quality conformance inspection. Unless otherwise specified, sampling for inspection shall be performed in accordance with MIL-STD-105. 4.2.1 Components and materials inspec

29、tion. In accordance with 4.1, components and materials shall be inspected in accordance with all the requirements of referenced documents unless otherwise excluded, amended, or qualified in this document or applicable purchase documents. 4.2.2 End item inspection. The wrapping paper shall be examine

30、d for the defects listed in 4.2.2.1 through 4.2.2.4. The lot size shall be all the rolls of the same type submitted at one time as specified in 4.2.2.1 through 4.2.2.4. 4.2.2.1 Examination for visual defects. The rolls of wrapping paper shall be examined for the defects listed in table II. The sampl

31、e unit for this examination shall be three randomly selected finished rolls of two yards in length and the full roll width. No sample units shall be taken from the first or last convolutions of the roll. Both sides of the sheet shall be examined. Defects of each type shall be scored only once within

32、 a sample unit. The inspection level shall be S-3 and the acceptable quality level (AQL) shall be 4.0, expressed in terms of defects per hundred units. TABLE II. Visual examination Examine Defect Workmanship Not clean: presence of any foreign matter, dirt, sand, grit, or oil spots. Presence of any c

33、ut, tear, puncture, chafed spot, wrinkle or fold. Edges not clean cut: ragged, crushed or uneven. Identification Missing, illegible, incorrect, incomplete, or do not markings conform to legend specified in 3.7. 4.2.2.2 Examination for dimensional defects. The rolls of wrapping paper shall be examine

34、d for the defects listed in table III. The sample unit shall be one finished roll selected at random. The inspection level shall be S-3 and the AQL shall be 4.0, expressed in terms of defects per hundred units* 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

35、om IHS-,-,- MIL-P-130F 81 R 9999706 0278991 L m MIL-P-130F TABLE III. Dimensional examination Examine Defect Width Varies by more than +1/8 inch and -1/16 inch when crepe Varies by more than +1/8 inch when creping is in is in cross direction machine direction 07 in both directions Core plugs Plug ho

36、les not centered Diameter of plug hole less than 1 inch or more than 1 1/4 inches Core Length less than specified width of roll material or Inside diameter less than 3 inches or more than greater by more than 1/4 inch, 3 1/8 inches Identification More than 36-inch distance along iength between group

37、s markings of marking More than 18 inches in width between groups of markings 4.2.2.3 Examination for defects in roll construction. The rolls of wrapping paper shall be examined for the defects listed in table IV. The sample unit for this examination shall be one finished roll. The inspection level

38、shall be S-3 and the AQL shall be 4.0, expressed in terms of defects per hundred units. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-130F TABLE IV, Roll construction examination Examine Defect Assembly of roll Not suitably restrained to pr

39、event unwinding Material not wound evenly and tightly on Material not wound on core Core broken, collapsed, crushed, or mutilated Core plugs omitted or not as specified roll causing wrinkles, creases, or telescoping Unwinding of When unwound, material sticks together to the extent rolls (examine tha

40、t unrolling causes tearing or injury to any surface both sides) Roll not continuous More than 1 splice in any 50 consecutive yards of roll Splice not evenly and neatly made; does not cover entire Splice comes apart during unwinding Splice not flagged with colored marker width of material 4.2.2.4 Exa

41、mination for length of roll. The sample for this examination shall be one finished roll. The average length of the rolls examined shall. be not less than the length specified, and the length of any individual roll shall be not less than 95 percent of the specified length. * 4.2.3 Packaging inspectio

42、n. An inspection shall be made to determine that packing and markings comply with requirements of section 5. Defects shall be as specified in table V. The lot size shall be the number of shipping containers in the inspection lot. The sample unit for this inspection shall be one randomly selected shi

43、pping container, fully packed. The inspection level shall be S-2 and the AQL shall be 2.5, expressed in terms of defects per hundred units . 8 I - I I I ! I i l I I I I I I 1 I I l l Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-130F TABLE V.

44、 Packaging inspection Examine Defect Packing Container not as specified Not in accordance with contract requirements Not level specified Rolls not overwrapped as specified Wrapper material other than specified for applicable Headers, inside or out, omitted or not of same material Closures not accomp

45、lished by specified methods or Inadequate application of components such as incomplete level as overwrap materials closure of case liner, container flaps, loose or inadequate sealing, strapping, or stapling I; Bulged or distorted container Markings Illegible, incomplete, omitted, or not in accordanc

46、e with contract requirements 4.2.4 Examination for palletization. An examination shall be made to determine that the palletization complies with therequirements of section 5. Defects shall be in accordance with table VI. The lot shall be the number of palletized unit loads in the end item inspection

47、 lot. The sample unit shall be one palletized unit load fully packaged. The inspection level shall be S-1 and the AQL shall be 6.5 defects per hundred units. 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-130F 81 m 977990b 0278794 7 m MIL-P-

48、130F TABLE VI. Examination of palletization . Examine Defect Finished Length, width or height exceeds specified maximum dimensions requirement Palletization Not as specified Pallet pattern not as specified Wood cap not used over and under the load Load not bonded with required straps as specified .

49、Weight Exceeds maximum load limits Marking Omitted; incorrect; incomplete; illegible; of improper size, location, sequence or method of application 4.3 End item testing. The end item shall be tested for the applicable characteristics listed in table VII. The lot size shall be the number of rolls in the end item inspection lot and the sample unit shall be one full roll-width sheet of 48 inch length.