ARMY MIL-P-1577 D-1976 MILITARY SPECIFICATION nPANEL MARKER RED CROSS 8 FEET 6 INCHES BY 19 FEET 6 INCHES《8英尺 16英寸乘19英尺 6英寸红十字嵌板标志》.pdf

1、HIL-P-LS77D 84 W 9999906 O372239 8 U - - - =_ - MIL-P-1577D 30 September 1976 SUPERSED I NG MIL-P-1577C 9 30 December 1966 MILITARY SPECIFICATION PANEL FARKER. RED CROSS, 8 FEET) 6 INCHES BY 19 FEET) 6 INCHES TU npetite Vepan;tment o overstitched less than 1-1/2 inches on stitch type 401 . - NOTE: T

2、hread breaks not backstitched or not overstitched shall be classified as open seams. Stitching Backstitched less than 1/2 inch (except where ends ends are held down by other stitching or turned under ahem). . Not backstitched. Chain portion of stitching shows on outside of the and assembly panel mar

3、ker. component. n - .x - Any component part or required operation omitted (un- less otherwise classified herein). X Needle chews expected to develop into a hole. . X Seams badly pleated or puckered. Not as specified, or not authorized by the contracting - Repa i r s . x officer. . Less than specifie

4、d wid -by more than 1/4 inch, -by more than 1/2 inch, Not constructed as spec Hems Twisted or pleated. Reinforcements Misplaced: - . h: but not more than 1/2 inch. . - fied in section “C-Cl on dwg. - x -seriously affecting serviceability. . x -affecting serviceability, but not seriously. - Finished

5、dimensions less than specified by more than 1/2 inch . - Improperly applied, causing excessive fullness on rein- Not stitched to reinforced parts oz all sides or not Center piece set with center line off-cznter of marker Reinforcement “A“ set with center line off-center of Red Cross Vertical or hori

6、zontal center line of red cross off- forcements or reinforced parts. . - caught in seams or stitching of reinforced parts. - by more than one inch. . x center piece by more than 1/2 inch. . - panels center of marker halves: -by more than 1/2 inch, but not more than one inch. . - Any part of tbe mark

7、er, except red cross, not white. x -by more than one inch. . x Markings Omitted, incorrect, illegible, or misplaced. Cleanness Noticeable grease or oil stains; thread ends not trim- - med throughout. - Minor X X - X - - X - X X - X - X X X X - X X - - X X 4.3.3,1.2 Dimensional defects.- Any dimensio

8、n that is not within the specified tolerance shall be classified a defect. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-P-1577D 4 999990b 0372225 4.3.3.1.3 Inspection levels and acceptable quali,ty levels (AQLs).- The in- spection leve1spble

9、qal-ity -revels expressed in defects per hundred units shall be as follows: Inspection AQL 1 eve1 Major Total For defects appl icable to 4.3.3.1.1 II 15.0 40.0 For defects applicable to 4.3.3.1.2 S-4 (one class) 4.0 4.3.4 Examination of preparation for del ivery requirements.- An examination shall b

10、e made to determine that packaging, packing and marking comply with the re- quirements of section 5 of this specification. Defects shall be scored in accord- ance with the list below. The sample unit shall be one shipping container fully prepared for delivery with the exception that it need not be s

11、ealed. tainers fully prepared for delivery shall be examined for the defects of closure listed below. The lot size shall be the number of shipping containers in the end item inspection lot. The inspection level shall be S-2 and the acceptable quality level shall be 2.5. Shipping con- Exami ne Defect

12、 Ma rk i ngs (ex ter i or Omitted, incorrect, illegible, of improper size, location, Mater ia Is Any component inissing, any component damaged, affecting Workmanship Inadequate application of components, such as, incomplete Con tents Number per container is more or less than required. and interior)

13、sequence, or method of application. serviceabi 1 ity. . closure of container flaps, inadequate stapling. 4.4 Tests.- Testing shall be in accordance with FED-STD-191. Fastness shall be in accardance with method 5804. . PREPARATION FOR DELIVERY 5.1 Packaging.- Packaging shall be levei A or C, as speci

14、fied (see 6.2). 5.1.1 Level A.- Each marker shall be laid out flat, face up. All lines shall The Tength shall be folded in half with the be neatly placed on top of the marker. lines on the inside. The length shall then be folded in thirds with the resultant dimension approximately 36 inches. The wid

15、th shall be folded in thirds with the completely folded marker measuring approximately 36 inches by 30 inches. Care shall be taken to expel th air during the folding operation to form a neat and compact bundle. The bunde shall be cross tied with cotton cord or twine. 5.1.2 Level C.- The panel marker

16、 shall be packaged to afford adequate protec- tion against deterioration and damage during shipment from supply source to the first receiving station. 5.2 Packing.- Packing shall be level A, B, or C, as specified (see 6.2). 7 Provided by IHSNot for ResaleNo reproduction or networking permitted witho

17、ut license from IHS-,-,-MIL-P-1577D q M 7997706 0372226 5 M M I L-P- 15770 5.2.1 Level A.- Two panel markers packaged as specified in 5.1.1, shall be packed in a snug-fitting fiberboard shipping container conforming to class Weather- resistant, grade V2s of PPP-6-636. Closure and reinforcement shall

18、 be in accord- ance with the appendix of the container specification. The weight of each ship- ping container shall not exceed the size and weight limitations of the container specification. 5.2.2 Level B.- Two panel markers packaged as specified in 5.1.1, shall be packed in a snug-fitting fiberboar

19、d box conforming to class Domestic, grade 275 of PPP-6-636. Closure shall be in accordance with the appendix of the container spec- ification. The weight of the contents of each shipping container shall not exceed the size and weight-1 imitations of the container specification. 5.2.3 Level C.- Panel

20、 markers packaged as specified in 5. such a manner to insure carrier acceptance and safe delivery at lowest transportation rates available for such supplies. Shipp be in accordance with the rules and regulations of the carriers mode of transportation. 5.3 Marking.- In addition to any special marking

21、 required , shall be packed in destination at the ng containers shall appl icable to the by the contract or order, interior packages and shipping containers shall be marked in accordance with MIL-STD-129. 6. NOTES 6.1 Intended use.- The red cross panel marker covered by this specification is intende

22、d to be used on tentage to designate that the tent is being used for med- ical purposes. 6.2 Ordering data.- Procurement documents should specify the fol lowing: (a) Title, number, and date of this specification. (b) When standard samples will not be furnished (see 3.1). (c) When a first article is

23、required (see 3.2). (d) The selection of applicable levels of packaging and packing (see 5.1 and 5.2). Custodians: Army - IH Navy - SA Air Force - 99 Review Activities: Army - IH Navy - SA Air Force - DSA - CT User Activities: Army - SM Navy - MS Project No. 8345-0082 Preparing Activity: The Institute of Heraldry, United States Army 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ML-P-1577D 8 B r P t B B h P a $ b u 1 .t + I B B I 1 D 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-