ARMY MIL-P-48376-1976 PROJECTILE 155MM HE M692 AND M731 NON-METALLIC HARDWARE FOR《M692和M731 HE 155毫米炮弹的非金属硬体》.pdf

1、MIL-P-l376 13 7777706 03L755b 3 MIL-P-48376 (PA) 1 March 1976 MILITARY SPECIFICATION PROJECTILES, 155MM, HE: M692 and M731, NON-METALLIC HARDWARE FOR This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 This specification covers the Non-me

2、tallic Hardware for Projectiles, 155MM, HE: M692 and M731. 2. APPLICABLE DOCUMENTS 2.1 The following documents of the issue in effect on date of invitation for bids or request for proposal, form a part of this specification to the extent specified herein: SPECIFICATIONS FEDERAL MILITARY MIL-A-4 80 7

3、8 S TAIT DARDS FEDERAL Federal Test Method Standard No. 601 - Ammunition, Standard Quality Assurance Provisions, General Specification For - Rubber: Sampling and Testing FSC: -1320 THIS DOCUMENT CONTANS -+r 1 MIL-P-48376 33 E 06 0339565 4- t- CVCucv rl CuMrl . . MMM mom M I *. O O0 000 I In In a, a

4、d rn -P 5 oa d +F: Bcd 5% * a, d O .c k O rn* Fi a, -P a, 5 5 FI rll N n 3- 4 a cd k bD cd k rd a D D Q c - -_ .i. . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- I MIL-P-48376 13 7777906 03L75bb b m MIL-P-48376 (PA) 4.4.3 Testing.-Testing is desc

5、ribed in the First Article 4.4.4 and Quality Conformance Inspection Tables. Inspection Equipment.-The inspection equipment required to perform the examinations and tests specified, herein is described in the “Paragraph Reference/Inspection Method“ column in the tables starting with paragraph 4.4.2.1

6、 The contractor shall submit for approval inspection equipment designs in accordance with the terms of the contract. See MIL-A-48078. 4.5 Test Methods and Procedures.- 4.5.1 Durometer Hardness of Rubber Parts.-The parts to be subjected to this test shall be tested as specified in Method 3021 of Fed

7、eral Test Method Standard No. 601. Five (-5)- readings shall be taken on each part using the hardness scale specified in MIL-STD-417. The median value of the five readings shall be obtained by arranging the value of the readings from lowest to highest. The median reading will be the third (center) v

8、alue in the numerically arranged readings. If the median hardness of any part fails to comply with the applicable hardness requirement (See MIL-STD-417) for the grade number the lot represented by the sample parts shall be rejected. (:Non-destructive test). 4.5.2 Dimensional control of stamped parts

9、In place of the normal sampling associated with the Classification of Defects, and with the approval of the Contracting Officer, a sample of at least ten (10) parts shall be dimensionally in- spected to qualify the tool used in the stamping process for use in production. In addition, a random samp

10、le of five (5) parts shall be selected from the last portion of each hours production for dimensional inspection as a control of the tool during production. If any defective parts are found during qualification of the tool, the tool producing the defective part shall not be used in production. If an

11、y defective parts are found when inspection is per- formed for control of the tool, the tool producing the defective part shall be removed from production. Further, that portion of production since the last tool control check shall be returned to the contractor for corrective action. 11 Provided by

12、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-q376 13 E 9999906 03L95b7 M MIL-P-48376 (PA) All tools removed from production because of some fault, may, after reworking, be returned to production providing they pass the qualification test above. The cont

13、ractor may request a change of inspection frequency providing he presents objective evidence to the Contracting Officer to substantiate the request. Material Certification.-The contractor shall provide certification that each lot of material used to produce each part number complies with all materia

14、l requirement s. The cert i- fication for rubber shall include test results or statements which provide specific reference to each applicable requirement of MIL-STD-417 and assurance of compliance with each requirement, 4.5.3 5. PREPARATION FOR DELIVERY 5.1 Preservation and packaging.- 5.1.1 Level C

15、The hardware shall be preserved and packaged Each package shall contain only in accordance with MIL-STD-1169. one part number. Bulk packaging may be used. Pad, dividers, etc. shall be used to avoid damage to parts. 5.2 Packing 5.2.1 Level C.-The hardware, preserved and packaged as specified in 5.1

16、1 shall be packed for shipment in accordance with MIL-STD-1169. Each pack shall contain only one part number. i 5.3 Marking.-Marking of the carton shall comply with MIL-STD-1169. 5.4 Shipping.-When hardware from more than one lot is shipped at one time, each lot shall be kept separate and the divis

17、ion between lots clearly indicated to prevent mixing of the lots in transit. 6. NOTES 6.1 Intended Use.-The components covered by this specification are intended for use in the M692 and 14731 Projectiles. 6.2 Ordering Data.-See MIL-A-48078, 6-3 Submission of Designs for Approval.-See MIL-A-48078. Su

18、bmit equipment designs, as required, to Commander, Picatinny Arsenal, Attn: SARPA-&A-T-T, Dover, New Jersey 07801. 12 - Y- -. . . _-.- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-P-4837b 13 W 777770b 0339568 T W MIL-P-48376 (PA) 6.4 Submissi

19、on of results of contractor-conducted examinations and tests.-Data shall be submitted in accordance with data item DI-R-1721 on the DD Form 1423 for the contract. Custodian: Army-PA Preparing Activity: Arm-PA Project IJumber: 1320-A320 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-