ARMY MIL-P-48602-1976 PLOTTING BOARD XM19 (M19) W E《标图板 XM19 (M19)W E》.pdf

1、MIL-P-4b02 12 W 79777Ob 0322074 b U Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, Prankford Arsenal, ATTN: 19137 by using the self-addressed Standardization Document Improvement Pro

2、- posal (DD Form 1426) appearing at the end of this document or by letter. SARFA-MDM, Philadelphia, Pennsylvania -. MIL-P-48602 (MU) 30 September 1976 MILITARY SPECIFICATION PLOTTING BOARD, XMl9, W/E 1. SCOPE 1.1 This specification covers Plotting Board: xM19 with equipment consisting of Plotting Bo

3、ard Case 11733754 (see 6.1). 2. APPLICABLE DOCUMENTS 2.1 The following documents, of the issue in effect on date of invitation for bids or request for proposal, form a part of this specification to the extent specified herein. SPECIFIGATIONS Military MIL-F-13926 MIL-P-14232 MIL-1-45607 STANDARDS Fir

4、e Control Materiel: General Specification Governing the Manufacture and Inspection of Parts, Equipment and Tools for Ordnance Ma- teriel, Packaging of Inspection Equipment, Supply and Maintenance of Military MIL-STD-105 MIL-STD-109 Sampling Procedure and Tables for Inspection Quality Assurance Terms

5、 and Definitions hy Attributes DRAWINGS US Army, Frankford Arsenal F11746801 F11733754 Plotting Board, XMl9 Case, Plotting Board: 11733754 FSC -1220 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- HIL-P-qbOZ 12 M 4779706 0322075 8 M MIL-P-48602 (MU)

6、 (copies of specifications, standards, drawings, and publication required by suppliers in conmiection with specific procurement unctions should be obtained from the procuring activity or as directed by the contracting officer.) 3. REQUIREMENTS 3.1. Fabrication.- The plotting board shall be manufactu

7、red in ac- cordance with Drawing F11746801 and drawings pertaining thereto. plotting board case shall be manufactured in accordance with Drawing 11733754 and drawings pertaining thereto. The 3.2 General specification.- The contractor shall be responsible for adherence to and compliance with the foll

8、owing requirements of Specification MIL-F-13926: a. Order of precedence. b. Dimensions and tolerances. C. inorganic protective surface finishes, d. Part identification and marking. e. Workmanship 3.3 Environmental. 3.3.1 StoraRe temperatures.- The plotting board shall show no evi- dence of physical

9、failure and shall meet all performance requirements of this specification when thermally stabilized at a standard ambient temp- erature of between 60“ and 90“ Fahrenheit (F) after having been exposed to, and thermally stabilized at ambient temperatures of -50“ and +140“F. 3.3.2 Operating temperature

10、s.- The plotting board shall operate freely while exposed to and thermally stabilized at ambient temperature of -40“ and +125“F, subsequent to which the plotting board shall meet the requirements of 3.4 to 3.7 inclusive when checked at a standard am- bient temperature of between 60“ and 90P. 3.4 Acc

11、uracy.- With the conditions existing as designated in (a) through (e) below, and with checkpoints located on the base grid 2300 meters to the right and left of the “O“ disk line and on the 2300 meter line in each quadrant (total of four poipts) the board shall meet the requirements specified in 3.4.

12、1 through 3.4.4. Hole of the disk is engaged with outside diameter of pivot a, center of the base grid. b. Pin bottom of the deflection arm knob is inserted in the pivot center of the base grid. e. The “O“ azimuth index line of the disk in coincidence with the I1O“ index line on the base grid. . Pro

13、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-P-Li602 L2 m 9999906 0322096 T W - MIL-P-48602 (MU) 3.4.1 With the disk rotated 800 mils, the index lines on the disk shall intersect the four located points on the base grid within 10 mils. 3.4.2 The

14、 deflection arm scale, when rotated to the four established points, shall indicate 3250 meters .C 10 meters. 3.4.3 The deflection arm meter scale when superimposed on the base grid meter scales shall coincide at the 3500 meter lines within 10 meters. 3.4.4 The vernier scales of the base grid and def

15、lection arm shall coincide within 1.0 mil. 3.5 WARPAGE 3.5,l The maximum warp between the disk and the base of the plotting board shall not exceed .03 inch as measured at the outer edge of the disk. 3.5.2 The maximumwarpage of the deflection arm of the plotting board shall not exceed 0.03 inch, and

16、this warpage shall not extend in from the edges by more than 3/16 inch. 3.6 Surface finish.- The top surfaces of the disk and the base grid of the plotting board shall allow clear pencil markings and clean erasures as specified on pertinent drawings. translucent and have no defects such as pits, dig

17、s, scratches with depth, stains, or waves on the surface that may be mistaken for pencil marks. The lines and figures on the base grid, as seen through the disk, shall be clearly legible, The materials shall be 3.7 0perabilitY.- With the hole of the disk engaged with the pivot center and with the pi

18、n bottom of the deflection arm knob inserted in the pivot: center, the deflection arm and disk shall be capable of rotat- ing freely. the deflection arm and the disk shall be removable from the base with normal finger pressure and without causing permanent distortion. At a standard ambient temperatu

19、re of between 60 and 90F 3.8 Plotting Board Case 11733754.- The case shall conform to all requirements specified on Drawing F11733754 anc drawings pertaining there to. 4 . QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection.- Unless otherwise specified in the contract or purchase order, t

20、he supplier is responsible for the per- formance of all inspection requirements as specified herein. Except as otherwise specified, the supplier may utilize his own facilities or any other facities suitable for the performance of the inspection require- ments specified herein, unless disapproved by

21、the Government. The Gov- ernment reserves the right to perform any of the inspections set forth 3 - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-P-qb02 12 977970b 0322077 II MIL-P-48602 (M) in the specification where such inspections are deem

22、ed necessary to as- sure supplies and services conform to prescribed requirements. 4.1.1 General provisions.- The component and subassembly inspec- tion requirements of MIL-F-13926 form a part of the Quality Assurance Provisions of this specification. be as listed in MIL-STD-109. Definitions of insp

23、ection terms shall 4.2 First article (initial production) approval.- The requirement for first article approval and the responsibility (Government or contract- or) or first article testing shall be as specified in the contract. The sample for first article approval tests shall consist of three (3) p

24、lotting boards, with casesI plus three (3) each of a11 items covered by SQAP. the same materials, equipment, processes, and procedures as used in regular production. All parts and materials, including packaging and packing, shall be ubtained from the same source of supply as used in regular producti

25、on. The sample shall be manufactured in the same manner, using 4.2.1 Government testing.- When the Government is responsible for conducting first article approval tests, the contractor, prior to sub- mitting the sample to the Government, shall inspect the sample to insure that it conorms to all the

26、requirements of the contract and submit a record of this inspection with the sample, including certificates of con- formance for materials. 4.2.2 Contr,actor testing.- When the contractor is responsible for The sample conducting first article approval tests, the sample shall be inspected by the cont

27、ractor for all the requirements of the contract. and a record of this inspection, including certificates of conformance for materials, shall be submitted to the Government for approval. The Government reserves the right to witness the contractors inspection, 4.3 Inspection p,rovisions, 4.3.1 Submiss

28、ion of product.- Unless otherwise specified by the Contracting Officer, inspection lot she, lot formation and presenta- tion of lots shall-be in accordance with “Submission of Product“ pro- visions of MIL-STD-105. 4.3.2 Examination and tests. 4.3.2.1 Components an4 subassemblies.- All components and

29、 subassem- blies shall be inspected in accordance with the inspection provisions con- tained in Supplementary Quality Assurance Provisions (SQAP) listed in the technical data package (TDP). Quality Assurance Provisions of MIL-F-13926 shall apply. In the absence of SQAPs, the applicable 4 Provided by

30、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-=- MIL-P-4b02 12 m 99797Ob 0322098 3 m MIL-P-48602 (MU) 4.3.2.2 Plotting board, wlth case.- Examination and tests related to Section 3 herein shall be performed on a class basis in accordance with MIL-STD-105 and

31、the sampling plans specified in Tables I, II and III herein. Examination and tests for packaging, packing and marking shall be in accord- ance with MIL-P-14232 and Section 5 herein, The tabulated classification of defects in Tables I, II and III shall constitute the minimum inspection to be performe

32、d by the supplier after first article approval and prior to Government acceptance or rejection by item or lot. TABLE I - CLASSIFICATION OF DEFECTS CLASS - CRITICAL: NONE MAJOR: AQL 1.07, DEFECTIVE REQUIREMENT TEST PROCEDURE 101. Accuracy 3.4 4.6.3 102. Warpage between disk and base. 3.5.1 4.6.4 103.

33、 Warpage, deflection arm 3.5.2 4.6.5 104. Surface finish, disk and base grid 3.6 4.6.6 105. Operability 3,7 4.6.7 106. Plotting board case 3.8 4.6.8 MINOR: NONE NOTE: The tests in Table I shall be conducted at a temperature between 60 and 90F. 4.3.3 Acceptance and rejection.- Rejected lots shall be

34、screened for all defective characteristics. and resubmittance of r.ejected lots shall be in accordance with “Acceptance and Rejection“ as specified in MIL-STD-105. Removal or correction of defective units 4.4 Special sampling. 4.4.1 General.- One plotting board, with case, shall be selected at rando

35、m as a special sample from each 100 produced or from each months production, whichever occurs first. and tests in Table II. The sample shall meet the requirements TABLE II -* NO 301. 302. CHARACIIERISTIC REQUIREMENT TEST PROCEDURE F abr ic at ion 3.1 Applicable draw- General specification 3.2 ing -

36、visual visual MIL-F-13926 - 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-Yb02 12 777770b O322099 5 7 MIL-P-48602 (MU) NOTE: The tests in Table II shall be conducted at a temperature between +60 and +90F. 4.4.2 Environmental.- Three plottin

37、g boards, without case, shall be selected at random as samples from each 50 produced, or from each months production, whichever occurs first, and tests in Table III, and shall then meet the requirements and tests in Table I. Each sample shall meet the requirements TABLE III - NO. CHARACTERISTIC 303.

38、 Storage temperature 304. Operability (-5OO and +140F) (-40 and +125F) REQUIREMENT TEST PROCEDURE 3.3,1 406.1 3.3.2 4.6.2 4.4.3 Failure of sample,- Should any one item of a special sampling fail to meet the specified test requirements, acceptance of the represented inspection lot will be suspended b

39、y the Government until necessary correc- tions have been made by the contractor and resubmitted items have been approved (see 4.3.3) 4.5 Inspection equipment.- Except as otherwise provided for by the contract, the contractor shall supply and maintain inspection equipment in accordance with the appli

40、cable requirements of MIL-1-45607. 4.5.1 Government furnished inspection equipment.- Where the contract provides for Government furnished,test equipment, supply and maintenance of test equipment shall be in accordance with the applicable requirements speci- fied in MIL-I-45607. 4.5.2 Contractor furn

41、ished inspection equipment. 4.5.2.1 Government design.- All inspection equipment specified by drawing number in specification or SQAP forming a part of the contract shall be supplied by the contractor in accordance with technical data included in the technical data package list. 4.5.2.2 Contractor d

42、esign.- In the absence of Government inspection equipment designs, the contractor shall design and supply inspection equip- ment compatible with the “Test Methods and Procedures“ specified in 4.6 of this specification and with the component inspection procedures specified in “Examination“ and “Test

43、Facilities“ requirements of MIL-F-13926. Since tolerance of test equipment is normally considered to be within 10% of the product tolerance for which it is intended, this inherent error in the test equipment design must be considered as part of the prescribed product toler- ance limit. Thus, concept

44、, construction, materials, dimensions and tolerances Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-48602 32 U 7999706 0322300 !I = MIL-P-48602 (MU) used in the design of test equipment shall be so selected and controlled as to insure that the

45、 test equipment will reliably indicate acceptability of a product which does not exceed 9W1, of the prescribed tolerance limit, and permit positive rejection when non-conforming. Construction shall be such as to facilitate routine calibration of test equipment. 4.5.2.3 Inspection equipment design re

46、quirements for temperature test- The volume of the test chamber shall conform to the test facilities ing.- requirements of MfL-F-13926. shall be in accordance with the specified requirements within plus or minus 2.SF. The temperature gradient across the cross-sectional area occupied by the test item

47、s shall not exceed 0.5F per foot in any direction. heat source of the test chamber shall be so located that radient heat, if used, will not fall directly on the test item. temperature sensors utilized to determine or control the specified chamber temperature shall be centrally located within the tes

48、t chamber in the supply airstream, or in the return airstream, whichever provides the specified test condition at the item under test and shall be baffled or otherwise protected against radiation effects. The air temperature at the control sensor The Thermocouples or equivalent 4.6 Test methods and

49、procedures. 4.6.1 Storage temperature.- Testing equipment utilized in this test shall conform to the requirements of 4.5.2.3. The Plotting board shall be placed in the test chamber and the temperature of the chamber reduced, over a period of 4 hours plus or minus 15 minutes, from room ambient temperature to -50F. The plotting board shall be maintained at this temperature ex- treme for a minimum of 2 hours. Upon completion of the 2