ARMY MIL-P-63215-1978 PRIMER PERCUSSION M100 METAL PARTS FOR《M100型撞击引物金属部件》.pdf

1、 Y cs, 37-19 . MIL-P-b32L5 13 7777906 O345555 T = . MIL-P-63215 (AR) 29 December 1978 r Beneficid comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addresaed to: Commander, US Army Armament Research and Development Comman

2、d, Attn. DRDARQA, Dover, New Jersey 01801 by using the seli-addreaed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this doebent or by letter. * MILITARY SPECIFICATION PRIMER, PERCUSSION, Ml00 METAL PARTS FOR This specification is approved for use by U.S. Army.A

3、rmament Research and Development Command, Department of the Army, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 This specification covers the metal parts for one type of t percussion primer designated at Primer, Percussion, M100. 2. APPLICABLE DO

4、CUMENTS 2.1 The following documents of the issue in effect on date of invitation for bids or request or proposal, form a part of this specification to the extent specified herein. SPECIFICATION MILITARY MIL-A-48078 STANDARDS MILITARY MIL-STD- 1169 -.Ammunition, Standard Quality Assurance Provisions,

5、 General Specification for - Packaging, Packing and Marking for Ship- ment of Inert Ammunition Components FSC: 1390 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-P-63215 (AR) DRAWINGS ARMY .- 8838012 - Cup, Battery 8838015 - Plug, Firing 9327

6、403 - Plug, Closing 9277150 - Head Primer (Copies of specff ications, standard, drawings and publications required by suppliers in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer) . 3. REQUIREMENTS 3.1 Material.-

7、Materials shall be in accordance with applicable drawings and specifications. requirements specified on Drawings (dwg.) 8838012, 8838015, 9327403 and 9277150, as applicable, and with all requirements specified in applicable specifications a thorough, workmanlike manner. They shall be clean and free

8、of burrs, sharp edges, unblended radii, surface defects, cracks, chips, dirt, grease, rust and other foreign matter. The cleaning method used shall not be injurious to any parts nor shall the parts be 1 contaminated by the cleaning agent. All required marking shall be neat and sharply defined. . . 3

9、.2 Metal parts.-The metal parts shall comply with all 3.3 Workmanship.-All parts shall be fabricated and inished in 3.4 First article inspection.-This specification makes provisions for first article inspection. Requirements for the submission of first article samples .by the contractor shall be as

10、specified in the contract. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection and standard quality assurance.-Unless otherwise specified herein or in the contract, the provisions of MIL-A-48078 shall apply and are hereby made a part of this detail specification. f, -. Provided by IHSN

11、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-b32L5 13 M 7777906 0345557 3 . MIL-P-63215 (AR) 4.2 Classification of inspection.-The following types of inspection shall be conducted on this item: a. First Article Inspection. b. Quality Conformance Inspection.

12、 4.3 First article inspection 4.3.1 Submission.-The contractor shall submit a first article sample as designated by the Contracting Officer for evaluation in accordance with provisions of 4.3.2. The first article sample shall consist of 25 each of every component which have been produced by the cont

13、ractor (or furnished to him by a supplier). 4.3.2 Inspection to be performed.-The first article parts shall be submitted in accordance with paragraph 4.3.1, and will be subjected by the Government to any or all the requirements of the applicable drawings and to the inspection in 4.4. 4.3.3 Rejection

14、.-See MIL-A-48078. 4.4 Quality conformance inspection 4.4.1 Inspection lot formation.-Inspection lots shall comply with the lot formation provisions of MIL-A-48078. 4.4.2 Examination.-See MIL-A-48078. a. Sampling Plans.-Unless otherwise specified in the Classification of Defects and Test Tables, sam

15、pling plans for major and minor defects shall be in accordance with MIL-STD-105, Inspection Level II, exc.ept that continuous sampling plans in accordance with MIL-STD-1235 may be used if approved by the procuring activity. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted witho

16、ut license from IHS-,-,-VI VI c E . # c F h. a 2 f Y? mmm . 4J c, 3 d 5 d 9) 8 g4 O E *- o n N E Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I rn c I- P 3 4 ?i N .a Provided by IHSNot for ResaleNo reproduction or networking permitted without lice

17、nse from IHS-,-,-MIL-P-632L5 13 7797706 03455b0 3 = . $ -4 VI rn . . id rlmwmar-am & rlcvmwar-c 0000000000 o 0000000 rlr(rldrlrlrlrlrlFl $1 NNNNNNNC & u Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-?Y? ? Y?“!? ?Y mmmmmmmmm mmm mmmmm mmm 7 Provided

18、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-P-63215 13 9797906 0345562 7 1 Fi k ti rl P “f? MMM cc, .Pl Q I 13. E e Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-63215 13 m 9799906 0345563 9

19、m MIL-P-63215 (AR) 4.4,3 Inspection equipment,-The inspection equipment required to perform the examinations and tests prescribed herein is described in the Paragraph Reference/Inspection Method column in tables starting with paragraph 4,4,2,1, submit for approval inspection equipment designs in acc

20、ordance with the terms of the contract. See Section 6 of MIL-A-48078. The contractor shall 5, PREPARATION FOR DELIVERY Sol Packing ang marking 5.1,1 Level C.-Packing and marking shall be in accordance with MIL-STFIIF37 6. NOTES 6,1 Ordering data.-See MIL-A-48078. 6.2 Submission of designs for approv

21、al.-See 6,2,3 of MIL-A-480/8. Submit equipment designs as required, to Conanander, ARRADCOM, ATTN: DRDAR-QAR-I, Dover, New Jersey 07801. Custodian: Army-AR Preparing Activity : Army-AR Project Number: 1390-A169 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-