ARMY MIL-P-63316 (2)-1993 PRIMER BATTERY ELECTRIC PARTS FOR AND LOADING ASSEMBLING AND PACKING《引物用电池电子零件及其装药 组装和包装》.pdf

1、MIL-P-633Lb (21 W 9999906 1854481 691 W I INCH-POUND I MIL-P-63316 (AR) AMENDMENT 2 09 ADril 1993 SUPERSEDING AMENDMENT 1 9 February 1981 MILITARY SPECIFICATION PRIMER, BATTERY, ELECTRIC PARTS, FOR AND LOADING, ASSEMBLING AND PACKING This Amendment forms a part of MIL-P-63316 (AR), dated 24 July 197

2、9, and is approved for use by the U.S. Army Armament, Munitions$ and Chemical Command, and is available for use by all Departments and Agencies of the Department of Defense PAGE 3 * 3.4.1.1 NO-fire test. Delete “(70 + 10F)” and substitute “(Ambient only)”. * 3.4.1.2 All-Fire output test. Deleee “(70

3、 + 100)“. - Add the following paragraph: “3.4.2 Test temperatures and conditioning, The battery primers shall b e temperature conditioned for a minimum of one (1) hour prior to testing. Condibioning temperatures are as follows: a. Cold: Minus forty-five degrees Fahrenheit, minus five degrees Fahrenh

4、eit (-40F - 5OF). b. Ambient: Sevenky degrees Fahrenheit plus or minus ten degrees Fahrenheit (+70F - + 5OF)”. c. Hot: One hundred and forty-five degrees Fahrenheit, plus five degrees Fahrenheik (+145O t OF)“. 0 AMSCN/A 1 of 4 FSC 1345 DISTRIRUT ION STATEMFNT 4 . Approved for public release; distrib

5、ution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-b33Lb (2) = 9999906 385Li482 528 MIL-P-63316 (AR) AMENDMENT 2 PAGE 4 * Submission. Delete “Primer, Babtery, Elecbric 9292624 150“ and substitube “Primer, Batbery, Elecbric 9292

6、624 300“ PAGE 7 * TABLE I - FIRST ARTICLE INSPECTION, Sheeb 2 Of 2: Prime, Babkery, Elecbric, Delete “150“ and subskitube “300“. SensitiviBy and oubput Besk, Delebe in ibs enkireky and substzitruts bhe following: “Sensikivitry and Oubput Tests 225 No-fire keck (Ambient? only) 225-0-1 3.4.1.1 4.5.4.1

7、 (+700F - t 10F) All-fire oubpuiz esk-Hob (+1450F t 5OF) Sleeve enlargemenk Dent? in plabe All-fire oui!puti Besk-Cold (-40F - 5OF) Sleeve enlargement Dent in plabe 75-0-1 3.4.1.2 4.5.4.2 75-0-1 3.4.1.2 4.5.4.2 O 75-0-1 3.4.1.2 4.5.4.2 75-0-1 3.4.1.2 4.5.4.2 All-fire outiput besk-Ambienb (+7OoF - +

8、10F) Sleeve enlargemenk 75-0-1 3.4.1.2 4.5.4.2 Denk in plabe 75-0-1 3.4.1.2 4.5.4.2“ PAGE 14 4.4.2.6, Major 101: “Cerkificaibon“ correcbed to “Cerizification“. PAGE 15 4.4.2.7, Major 101: “Diamer“ correcked Co “Diameber“ - “Gage bo “Visual“. Major 104: “Separbed correctied bo “Separabed“. 2 Provided

9、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-63316 (2) m 777Ob 1854483 Yb4 m MIL-P-63316 (AR) AMENDMENT 2 PAGE 16 4.4.2.8: * Delete “Sensitivity and Output Test, (+70F + OF) 125 .I and substitute “Sensitivity and output test, 150 .O. * Major 111: De

10、eke “. (a) 125-1-2 ,I and substitute Major 112: Delete “. 125-1-2 .,.“ and substitute * Major 113: Delete “., dent in place 125-1-2 ,I and substituke I., .dent in plate - 2/ 150-1-2 , , .O, . . .i/ - 150-1-2 . . .“. “ . . .2/ - 150-1-2 . “ NOTES: * Delete note a in its entirety and substitute the fo

11、llowing: “1/ 150 samples from NO-fire test to be used to perform All-fire tests below.“ 2/ 50 Samples at each temperature (Hot, Cold, and Ambyent) shall be tested for All-fire tests. See 3.4.2 for temperature conditioning.“ PAGE 17 4.4.2.8, Major 118: Add 3.5.2 to the requirement paragraph, 4.4.5.1:

12、 Delete Dwg 9275629. 4.4.5.1 .a: Delete Dwg “9275663“ to “9275631“. Change ,003 to 0.55 - + .001“ to “.O03 to 0.055 - t ,001“. 4.4.5.1.b: Delete “copper-zinc lead allor rod , on the outside diameter“. Add “Brass allow 360, having a hardness equivalent to Rockwell 40-55 measured on the outside diamet

13、er while supporting the inside diameter. 4.4.5.1: Add paragraph d and e: “d. The makerial for the wikness plate, Dwg 9275633 shall be Grade C lead. e. The iridite finish of the base, Dwg 9275632 is optional, 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

14、IHS-,-,-MIL-P-633Lb (2) M 9999906 3854484 3T0 MIL-P-63316 (AR) AMENDMENT 2 PAGE 20 4.5.4.1: Add senbence: NO-fire may be performed on a group of units connected in series before assembly to kesb equipmenb for oubput? best. if one or more primers funcbion, bhe remaining primers connected in series sh

15、all be retiesfed. * 4.5.4.2 All-fire output Desk. Deleke “(700 + 10F). Followinq khe . shall b e fired . . and sbst!itube Following Dhe No-fire test of 4.5.4.1, the battery primer samples shall be equally divided into khree (3) groups: one group besised at? hot! (+145OF t SF), one group besbed aD co

16、ld (-4OOF - 5OF), and one group Beshed ab ambient! (+70F + 10F). The babbery primers shall be temperaFure condikioned for a minimum of one (1) hour prior to kesDing per bheir respective group temperabures. The babbery primers shall be fired .I. PAGE 22 4.5.7: Delebe The measuremenb shall be made wit

17、h a meter capable of measuremenb bo $he nearest 0.01 ohm. PAGE 23 6.1 Change “XM74 and “XM75 AT/AV to “M74“ and “M75 AT“. Add XM77 AP, XM78 AT/AV. 6.5: After khe words period of kirne“ add or ab the request of trhe Contracking Officer . * 6.5.1 Sensibiviky and oubput: Delete TWO hundred (200) baftie

18、ry primers , . . and subSkiDuke TWO hundred and Den (210) bakkery primers . The margins of this amendmen$ are marked with an asferisk or vertical lines to indicabe where changes (addibions, modifications, corrections, delekions) from the previous amendmenk were made. This was done as a convenience o

19、nly and the Governmenb assumes no lbabiliby whabsoever for any inaccuracies in khese nohatiions . Bidders and conbrackors are cautioned bo evaluabe the requiremenbs of Chis documenb based on the enhire conbenk irrespecbive of &he marginal noDaCions . and relabionship Do he lasb previous amendmenti. Cuskodian: Army-AR Preparing Actii vi by : Ar my - AR (ProjecB 1345-A616 1 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-