ARMY MIL-P-70819-1991 PRIMER ELECTRIC M128 LOADING ASSEMBLING AND PACKING《M128式电引物的装药 组装和包装》.pdf

1、! 1 1 t r I l I t. i ! I P L i I t I l. MIL-P-70819 13 m 9999906 0484213 m I INCH-POUND I MIL-P-70819 (AR) 28 February 1991 MILITARY SPECIFICATION PRIMER, ELECTRIC, MI28 LOADING, ASSEMBLING AND PACKING This Specification is approved for use within the U.S. Army Armament, Munitions and Chemical Comma

2、nd, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1. Scope. This specification contains requirements and provides quality assurance provisions for loading, assembling and packing of the MI28 Electric Primer. 2 . APPLICABLE DOCUMENTS 2.1 Government

3、documents. 2.1.1 Specifications standards and handbooks. The following sDecifications. standards, and handbooks form a part of this document t8 the extent bpecified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of S

4、pecifications and Standards (DODISS) and supplement thereto, cited in the solicitation. SPECIFICATIONS MILITARY MIL-P-116 MIL-B-I 17 MIL-P-223 MIL-A-48078 . Preservation, Methods of, - Bags., Sleeves and Tubing - Interior . Packging. - Powder, Black. - Ammunition, Standard Quality Assurance Provisio

5、ns, General Specification for. Beneficiai comments (mxmmmdatim, addtiw, deletions) and any pertinent data which may be of use in improving this document shd be to: Commander, U.S. Amy ARDEC, Al“: SMCAR-BAGS, PicatiMy Arsena, New Jersey W8065000 by ushg the aeif-adcbsed standardization Document Impro

6、vement Proposai (DD Form 1426) appearing at the end of this document or by letter. - AMSC NIA FSc 1390 1 A, Approved for public release; distribution is uniimitai. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDS MILITARY MIL-STD-129 - Mar

7、king for Shipment and Storage. MIL-STD-286 - Propellants, Solid: Sampling, MIL-STD-1234 - Pyrotechnics, Sampling Inspection and Examination and Testing Inspection by Attributes. Testing. (Unless otherwise indicated, copies of federal and military specifications, standards and handbooks are available

8、 from the Standardization Documents Order Desk, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 191 11-5094.) The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the

9、 solicitation. P 2.1.2 Other Government documents, drawings, and publications. DRAWINGS ARMY 8847545 - Box, Fiberboard, Packing, Ammunition 8847546 - Box, Packing, Ammunition, for Primer, e for Primer, Electric. Electric. 12910250 - Primer, Electric, Loading Assembly, M128. (Copies of Government doc

10、uments, drawings and publications required by contractors in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer.) P UBL IC AT I ON S (Title) 49 Code of Federal Regulations Transpor tat i on of Haza r dou s Ma ter i

11、als. (Application for copies should be addressed to the Regulations Managenent Corp., 4 Old Red Lion Rd., Vincentown NJ, 08088-8632.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-70819 33 m 9999906 0484235 3 m -7: MIL-P-70819 (AR) 2.2 Orde

12、r of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. e 3. REQUIREMENTS 3.

13、1 Material. Materials and parts shall be in accordance with 3.2 Primers. The loaded primers shall comply with all applicable drawings and specifications. .5. requirements speoified on drawing 12910250 and applicable specifications. 3.3 Moisture content. 3,3*1 Ignition element charge. The moisture co

14、ntent of the r ignition element charge composition after drying shall not exceed 0.02 percent. 3.3.2 Black powder. The moisture content of the black powder at the time of loading the closing plug shall not exceed 0.50 percent. 3*3.3 Benite. The moisture content of Lhe benite at the loading station a

15、t the time of loading shall not exceed 1.00 percent. - 3.4 Ignition element charge composition. The chemical composition of the ignition charge shall be: Component Percentage Potassium Chlorate and Gum Solids 46.1 + 2.1% Lead Thiocyanate 35.5 2.0% Charcoal 20.0 - + 1.5% 3.5 Lacquer in flash holes. T

16、he lacquer in primer body flash 3.6 Assembly torque. Threaded joints shall withstand subsequent holes shall comply with illustration 1, 2, or 3 of Figure 1. reapplication of the minimum assembly torque specified on the applicable drawing, without moving, while thread sealing compounds are wet. 3.7 E

17、lectrical resistance test. The electrical resistance of the head loading assembly when measured between the primer head (dwg, 9327339) and the electrode (dwg. 8839507) shall not be less than 0.80 ohms or more than 1.80 ohms. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted with

18、out license from IHS-,-,-_ MIL-P-70817 13 m 777770b 0484236 3 m MIL-P-70819 (AR) 3.8 Functioning/non-functioning test of head loading assembly. 3.8.1 Functioning. The head loading assembly shall function when a current of 1.25 amperes, maximum, is applied. 3.8.2 Non-functioning. The primer loading a

19、ssembly shall not function when a current of 190 to 200 milliamperes is applied. 3.9 Proving ground. The primer shall comply with the following requirements when fired ballistically: a. The primer shall not fail to fire. b. The primer body shall not rupture or become detached. c. There shall be no a

20、udible hangfire(s1. d. The primer shall not squib. e. The tip shall not become separated from the body. 3.10 Check test for possible deterioration of primers. Check tests are designed to prevent loading ammunition items with primers which have deteriorated. They should be performed on each lot of pr

21、imers which have been stored for more than two years or which have been sub Qected to any adverse conditions, however brief, within that period of time. The following tests are specified: a) Moisture Content of Benite b) Electrical Resistance cl Functioning d Non-Fun ct ioni ng 3.11 First article in

22、spection. This specification contains technical provisions for first article inspection. Requirements for the submission of first article samples by the contractor shall be as specified in the contract. 3.12 Workmanship. All parts and assemblies shall be fabricated and loaded in accordance with the

23、applicable specifications and drawings, They shall be clean and free of burrs, sharp edges, unblended radii, surface defects, chips, dirt, grease and oil (except where specifically required), corrosion products and other foreign matter. The cleaning method used shall not be injurious to any part of

24、the assembly nor shall they be contaminated by the cleaning agent. Exterior surface coatings shall be continuous except for a few light scratches not exposing base material. All required markings shall be neat and sharply defined. Required packing shall be dry. 4 Provided by IHSNot for ResaleNo repr

25、oduction or networking permitted without license from IHS-,-,-,MIL-P-70839 33 0b 0484237 5 W MIL-P-70819 (AR) 1 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all in

26、spection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Governme

27、nt. The Government reserves the right to perform any of the inspections set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements . 4.2 Responsibility for compliance. All items shall meet all requirements of section

28、s 3 and 5. The inspection.set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in this specification shall not relieve the contractor of the responsibility of ensuring that all products or supp

29、lies submitted to the Government for acceptance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however, this does not authorize submission of known defective material, either

30、indicated or actual, nor does it commit the Government to accept defective material. 4.3 Inspection equipment. Inspection equipment required to perform the examinations and tests prescribed herein is described in the .ttInspection Method Reference“ column in the tables starting with 4.4.2 4.4 Classi

31、fication of inspections. The following types of inspections shall be conducted on this item: a. First article inspection b. Quality Conformance Inspection 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-P-70819 13 7999906 0484218 7 I MIL-P-708

32、19 (AR) 4.5 First article inspection 4.5.1 Submission. The contractor shall submit a first article sample as designated by the Contracting Officer for evaluation in accordance with provisions of 4.5.2. The first article sample shall consist of the following items in sample quantities indicated. Part

33、/Assembly Description Drawings Quantity Element, Ignition, Electric Loading Head Loading Assembly 9327345 400 Box, Fiberboard, Packing, Ammunition Box, Packing, Ammunition for As s em b 1 y 8839505 10 Closing Plug Loading Assembly 9327346 10 Primer, Electric, MI28 1291 0250 1 O0 for Primer, Electric

34、 8847545 5 Primer, Electric 8847546 5 4.5.2 Inspections to be performed. See MIL-A-48078 and Table I specified herein. 4.5.3 Rejection. See MIL-A-48078. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-70839 33 W 9999906 0484239 9 - c) cc (u o

35、 =f ulCa (u(uC0 ou303 * . . . 0. a .*. M =I- m Cu (u (u ma u3 ul ocoao * * =fa* . b b . . 0 . . . .o u) L .rl k a, Al .lJ f . a O Cu W =r Y . . . M 7 o (u W =;f N (u W =r o a 7 . . Y o M Y . M 7 . m In In In L O c O m .li c, 4J o .li a, 4-i a, c P 8 Provided by IHSNot for ResaleNo reproduction or ne

36、tworking permitted without license from IHS-,-,-MIL-P-70839 33 m 9999906 0484223 7 m - , MIL-P-70819 (AR) 4.6 Qualitv conformance insDection 4.6.1 Inspection lot formation. Inspection lots shall comply with lot formation provisions of MIL-A-48078. In addition. inspection lots of ioaded primers shall

37、 contain the following components from one lot interfix from one manufacturer: ignition element, metal parts, charge composition, and benite. Black powder shall be from one lot only. 4.6.2 Examination and tests. 4.6.2.1 Classification of characteristics. Quality conformance examinations and tests ar

38、e specified in the following Classification of Characteristics paragraphs. The contractors quality program or detailed inspection plan shall provide assurance of compliance of all characteristics with the applicable drawing and specification requirements utilizing as a minimum the conformance criter

39、ia specified herein. Unless otherwise specified herein, attributes sampling inspection shall be conducted in accordance with Table II below using Level I for major defects and Level II for minor defects. Samples shall be selected at random. e f 9 Provided by IHSNot for ResaleNo reproduction or netwo

40、rking permitted without license from IHS-,-,-MIL-P-708LS 13 m 999990b O484222 9 m MIL-P-70819 (AR) Table II Sampling Sampling Plan for Quality Conformance (Accept on Zero Defects) I I I I I Lot Size !Sample Size (Characteristic) I I I I Major I Mi nor I I I I I I I I I I 2 to 8 I I I I I I * I sc I

41、I I I 9 to 150 I 32 I 13 I I 151 to 500 I 32 I 30 I 501 to 1200 I 74 I 35 I I 1201 to 3200 I 74 I 43 I 3201 to 10000 I 87 I 50 I I 10001 to 35000 I 1 o9 I 61 I I I I I I I I I I I I I I I I I I I I * 100% inspection NOTE: If sample size equals or exceeds lot or batch size, do 100% inspection. 4.6.2.

42、2 Alternative inspection provisions. Alternative inspection procedures, methods or equipment, such as statistical process control, tool control, other types of sampling procedures, etc., may be used by the contractor when they provide, as a minimum, the level of quality assurance required by the pro

43、visions specified herein. Prior to applying such alternative procedures, methods, or equipment, the contractor shall describe them in a written proposal submitted to the procuring contracting officer for evaluation and approval by the Government (see 6.4). When required, the contractor shall demonst

44、rate that the effectiveness of the proposed alternative(s) is equal to or better than the specified quality assurance pro-!isions herein. In cases of dispute as to whether the contractorts proposed alternative( s) provide equal assurance, the provisions of this specification shall apply. All approve

45、d alternative inspection provisions shall be specifically incorporated into the contractors quality program or detailed inspection system, as applicable. . 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-z a O H H u W pi vl 2 H W t) 4 .E u IA O !4

46、 I v) .- MIL-P-708L9 II W 999990b 0484223 O W bD c .rl m O d o *li Fi s, o a, d a, c O .li s, c ho *rl m - -h s,d cn m E $4 g: =I- - Cu CuCu Cum =t r H H Hc- H o (t ccc L a, bD Fi 3 (I rn c o +Id a, r: s 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS

47、-,-,-Y LL O v- t W I v) MIL-P-70819 13 9999906 0484224 2 M h d P E rn rn (1 bo 4 a Cu O rl ho 7 d a bo C .rl v) O Irl 20 - - LL W CY HHH H HHHCU H # oalalaly al a a rl rl-d am m m- o o O 5 O a ma 4 I3 d ml . 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

48、 IHS-,-,-MIL-P-708h9 23 m 9999906 0484225 4 m Cu Cu . CupcCu Cu? o3 .a *e MMM MM M M HH HH HH HH M 7 d a h0 c dl 01 13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ho !2 .A a (I O d O L O -4 L a h d P B u) 03 (I L a, El -4 L a4 _ - MIL-P-708L9 13 9999906 0484226 b Li W I- O Z I- 0 W 3 (I (u 7 M M 8 8 H H H H a, a, d d P P (I (I B B a a, hD tu a, a a a H I I i 1 I I I I I I I I I I 14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I I- l ! I I I I I I I