ARMY MIL-PRF-55310 30 D-2008 OSCILLATOR CRYSTAL CONTROLLED TYPE 1 (CRYSTAL OSCILLATOR (XO)) 450 kHz THROUGH 100 MHz HERMETIC SEAL LOW VOLTAGE CMOS《晶体振荡器(XO) 450千赫-100兆赫的低压互补金属氧化物半导.pdf

1、AMSC N/A FSC 5955 INCH-POUND MIL-PRF-55310/30D 15 October 2008 SUPERSEDING MIL-PRF-55310/30C 09 June 2008 PERFORMANCE SPECIFICATION SHEET OSCILLATOR, CRYSTAL CONTROLLED, TYPE 1 (CRYSTAL OSCILLATOR (XO), 450 kHz THROUGH 100 MHz, HERMETIC SEAL, LOW VOLTAGE CMOS This specification is approved for use b

2、y all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-55310. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise

3、specified, tolerances are .005 (0.13 mm) for three place decimals and .02 (0.5 mm) for two place decimals. FIGURE 1. Dimensions and configuration. Pin number Function 1 Enable/Disable 2 GND 3 Output 4 VDDInches mm Ltr Min Max Min Max A N/A .560 N/A 14.22 B N/A .360 N/A 9.14 C .195 .205 4.95 5.21 D .

4、086 .114 2.18 2.90 E .025 .055 .635 1.40 F N/A .378 N/A 9.60 G .292 .308 7.42 7.82 H .007 .009 .178 .229 J N/A .188 N/A 4.78 K .015 .021 .381 .533 Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without licen

5、se from IHS-,-,-MIL-PRF-55310/30D 2 REQUIREMENTS: Interface and physical dimensions: See figure 1. Mounting: See figure 1. Pads: See figure 1. Seal: Hermetic in accordance with MIL-PRF-55310, maximum leakage rate 5 x 10-8 atm cc/s. Weight: 3 grams, maximum. Oscillator: Class 2 or any class 1 or clas

6、s 3 oscillator meeting all class 2 requirements and verification tests specified herein and in MIL-PRF-55310. Calibration: Manufacturer calibrated. Screening: In accordance with MIL-PRF-55310, product level B or S, as applicable. Temperature: Operating: See table I. Storage: -62C to +125C. Load test

7、 circuit: See figure 2. Output waveform: Symmetrical square wave, 3.3 volt CMOS logic compatible (see figure 3). Output logic voltage levels at designated CMOS (see figure 3): Logic 1: 90 percent of VDD, minimum. Logic 0: 10 percent of VDD, maximum. Rise and fall times: (See table I) Measurements sh

8、all be taken at the 10 percent and 90 percent peak-to-peak output voltage levels, with peak-to-peak output defined as level 1-level 0 (see figure 3). Duty cycle: See table I and figure 3. Supply voltage: +3.3 V dc 10 percent. Input current: At designated supply voltage (see table I). Enable/disable:

9、 Output disabled (high impedance): Pin 1 input 0.3 V dc. Output active: Pin 1 input 2.0 V dc or open. Output frequency: Frequency as designated at time of acquisition (see table I). Initial accuracy at reference temperature (up to 30 days after shipment): See table I. Copyright Communications - Elec

10、tronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55310/30D 3 TABLE I. Dash numbers and operating characteristics. 1/ Maximum input current for no load condition. 2/ See figure 3. Frequency-temperature to

11、lerance (one-half temperature cycle, referenced to frequency measured at +23C 1C, immediately prior to starting of the test): See table I. Measurements taken at ten equally spaced increments over the specified operating temperature range. 1/ Frequency-voltage tolerance: 4 ppm maximum for a 10 percen

12、t change in supply voltage. Measurements taken at reference temperature and operating temperature range end points. Frequency aging: Measurements shall be taken at +70C 0.2C at intervals of not more than every 72 hours for 30 days minimum. 10 ppm per year, maximum 1.5 ppm per 30 days. 3 ppm per 90 d

13、ays. Terminal strength: Method 211 of MIL-STD-202, test condition A. Applied force: 8 ounces each terminal. Frequency-environmental tolerance: Not applicable. 1/ For the purpose of transitioning this device to MIL-PRF-55310, Frequency stability versus temperature has been renamed Frequency-temperatu

14、re tolerance. The verification requirements of initial frequency-temperature accuracy (one-half temperature cycle) shall apply except that frequency measurements shall be referenced to the frequency measured at +23C 1C (fref) instead of to the nominal frequency (fnom). Pulse characteristics Frequenc

15、y-temperature tolerance (ppm) -55C to +125C -55C to +105C -20C to +70C Dash number Output frequency range Input current (max) 1/ Rise and fall times (max) 2/ Duty cycle min-max 2/ Initial accuracy at +23C 1C A B C 01 450 kHz to 14.999 MHz 8 mA 10 ns 45% to 55% 15 ppm 50 ppm 40 ppm 25 ppm 04 450 kHz

16、to 14.999 MHz 8 mA 10 ns 45% to 55% 25 ppm 100 ppm 80 ppm 50 ppm 11 15.000 MHz to 29.999 MHz 10 mA 10 ns 45% to 55% 15 ppm 50 ppm 40 ppm 25 ppm 14 15.000 MHz to 29.999 MHz 10 mA 10 ns 45% to 55% 25 ppm 100 ppm 80 ppm 50 ppm 21 30.000 MHz to 59.999 MHz 20 mA 5 ns 40% to 60% 15 ppm 50 ppm 40 ppm 25 pp

17、m 24 30.000 MHz to 59.999 MHz 20 mA 5 ns 40% to 60% 25 ppm 100 ppm 80 ppm 50 ppm 31 60.000 MHz to 85.000 MHz 30 mA 3 ns 40% to 60% 15 ppm 50 ppm 40 ppm 25 ppm 34 60.000 MHz to 85.000 MHz 30 mA 3 ns 40% to 60% 25 ppm 100 ppm 80 ppm 50 ppm 41 85.000 MHz to 100.00 MHz 30 mA 3 ns 40% to 60% 15 ppm 50 pp

18、m 40 ppm 25 ppm 44 85.000 MHz to 100.00 MHz 30 mA 3 ns 40% to 60% 25 ppm 100 ppm 80 ppm 50 ppm Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55310/30D 4 NOTES: 1. For CC

19、L= 15 pF 5 percent. 2. For RCL= 10 k 5 percent. 3. CCLincludes scope capacitance. FIGURE 2. Load test circuit. FIGURE 3. Waveform Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-M

20、IL-PRF-55310/30D 5 Vibration, sinusoidal: In accordance with MIL-PRF-55310 and method 204 of MIL-STD-202. Nonoperating: Test condition D. Operating: Not required. Ambient pressure: Nonoperating: In accordance with MIL-PRF-55310. Operating: Method 105 of MIL-STD-202, test condition C. Exposure time:

21、5 minutes. Reflow soldering: Reflow soldering of the unit at +230C 10C for 15 seconds shall not degrade the performance. Part or Identifying Number (PIN): Consists of “M” prefix followed by specification sheet number, a dash and coded alphas, and numeric number. See example: EXAMPLE M55310/30- S 01

22、A XXXXXXXX M prefix and specification sheet number Product level (S, B, or C) Dash number (see table I) Operating temperature range (A, B, or C) (see table I) Frequency Reference documents. In addition to MIL-PRF-55310, this document references the following: MIL-STD-202 The margins of this specific

23、ation are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this

24、 document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-5

25、5310/30D 6 Custodians: Preparing activity: Army - CR Army - CR Navy - EC Air Force - 99 Agent: DLA - CC DLA - CC Review activities: (Project 5955-2008-009) Army - AR, MI, SM Navy - AS, CG, MC Air Force - 19, 84 NASA - NA NOTE: The activities listed above were interested in this document as of the da

26、te of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-