ARMY MIL-PRF-55365 12 F-2012 CAPACITORS CHIP FIXED TANTALUM POLARIZED ESTABLISHED RELIABILITY AND NONESTABLISHED RELIABILITY STYLE CWR15.pdf

1、AMSC N/A FSC 5910 DISTRIBUTION STATEMENT A Approved for public release, distribution is unlimited. INCH-POUND MIL-PRF-55365/12F 17 September 2012 SUPERSEDING MIL-PRF-55365/12E 25 January 2011 PERFORMANCE SPECIFICATION SHEET CAPACITORS, CHIP, FIXED, TANTALUM, POLARIZED ESTABLISHED RELIABILITY AND NON

2、ESTABLISHED RELIABILITY, STYLE CWR15 This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-55365. FIGURE 1. Style CWR15 capacitors. F

3、IGURE 1. Dimensions and configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55365/12F 2 Case size L + .010 (0.25) - .006 (0.15) W + .008 (0.20) - .004 (0.10) H + .008 (0.20) - .004 (0.10) P + .014 (0.35) - .000 (0.0) L .063 (1.60)

4、.033 (0.84) .033 (0.84) .006 (0.15) R .079 (2.01) .053 (1.35) .053 (1.35) .006 (0.15) Case size L .008 (0.20) W .008 (0.20) H .008 (0.20) P + .014 (0.35) - .000 (0.0) A .126 (3.20) .063 (1.60) .063 (1.60) .006 (0.15) F .158(4.01) .116(2.95) .050(1.27) .010(0.25) NOTES: 1. Dimensions are in inches. 2

5、. Metric equivalents are in parentheses and given for general information only. 3. These capacitors are designed for mounting by dip soldering, reflow soldering, or other conventional means. 4. The anode (+) terminal shall be identified by a marking on all four sides or laser marking on one side of

6、the case. 5. Solderable surfaces are only those surfaces designated as such. Termination edges are not considered solderable. FIGURE 1. Dimensions and configuration - Continued. REQUIREMENTS: Dimensions and configuration: See figure 1. Termination finish: Termination finishes B, H, or K in accordanc

7、e with MIL-PRF-55365. DC rated voltage: See table I. Above +85C, voltage derating is required (see MIL-PRF-55365). Operating temperature range: -55C to +125C. Product level designator: In accordance with MIL-PRF-55365 except the Weibull Failure Rate Level grading failure count during and after test

8、shall be determined by DC leakage measurements of .045 X CV or 0.5A whichever is greater. DC leakage (DCL): See table I. Capacitance: See table I. Capacitance tolerance: 5 percent (J), 10 percent (K), or 20 percent (M). Dissipation factor (DF): See table I. Equivalent series resistance (ESR) at 100

9、kHz: In accordance with MIL-PRF-55365 (see table I). Resistance to soldering heat: In accordance with MIL-PRF-55365. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55365/12F 3 Stability at low and high temperatures: In accordance with MIL-PR

10、F-55365. Surge voltage: In accordance with MIL-PRF-55365. Life: 2,000 hours: In accordance with MIL-PRF-55365. 10,000 hours: In accordance with MIL-PRF-55365. Solderability: In accordance with MIL-PRF-55365 except that following steam aging, test samples may have a 30 minute bake out at +150C prior

11、to solder dipping and all terminations shall exhibit a continuous solder coating free from defects for a minimum of 75 percent of the critical area of any individual termination. TABLE I. Style CWR15 characteristics. Part or identifying number (PIN) 1/ DC rated voltage (+85C) (Volts) Cap. (nom) (F)

12、DC Leakage (max) (A) Dissipation factor (max) (percent) Max ESR 100 kHz +25C (Ohms) Case size +25C +85C +125C +25C +85C +125C -55C CWR15CK685-L- 4 6.8 .5 5 6 8 16 12 10 L CWR15CK106-R- 4 10 .5 5 6 8 16 12 6 R CWR15CK156-R- 4 15 .6 6 7 8 16 12 6 R CWR15CK226-R- 4 22 .9 9 11 8 16 12 6 R CWR15CK336-R-

13、4 33 1.3 13 16 10 20 15 6 R CWR15CK686-A- 4 68 2.7 27 33 15 30 23 1 A CWR15DK335-L 6 3.3 .5 5 6 6 12 9 10 L CWR15DK475-L- 6 4.7 .5 5 6 8 16 12 10 L CWR15DK685-R- 6 6.8 .5 5 6 8 16 12 6 R CWR15DK106-R- 6 10 .6 6 7 8 16 12 6 R CWR15DK156-R- 6 15 .9 9 11 8 16 12 6 R CWR15DK226-A- 6 22 1.4 14 17 10 20 1

14、5 6 A CWR15DK336-A- 6 33 2.0 20 24 10 20 15 6 A CWR15DK476-A- 6 47 2.8 28 34 15 30 23 4 A CWR15FK474-L- 10 0.47 .5 5 6 6 12 9 12 L CWR15FK684-L- 10 0.68 .5 5 6 6 12 9 10 L CWR15FK105-L- 10 1.0 .5 5 6 6 12 9 10 L CWR15FK155-L- 10 1.5 .5 5 6 6 12 9 10 L CWR15FK225-L- 10 2.2 .5 5 6 6 12 9 10 L CWR15FK3

15、35-R- 10 3.3 .5 5 6 8 16 12 6 R CWR15FK475-R- 10 4.7 .5 5 6 8 16 12 6 R CWR15FK685-R- 10 6.8 .7 7 8.5 8 16 12 6 R CWR15FK106-R- 10 10 1.0 10 12 8 16 12 6 R CWR15FK156-A- 10 15 1.5 15 18 10 20 15 6 A See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted w

16、ithout license from IHS-,-,-MIL-PRF-55365/12F 4 TABLE I. Style CWR15 characteristics - Continued. Part or identifying number (PIN) 1/ DC rated voltage (+85C) (Volts) Cap. (nom) (F) DC Leakage (max) (A) Dissipation factor (max) (percent) Max ESR 100 kHz +25C (Ohms) Case size +25C +85C +125C +25C +85C

17、 +125C -55C CWR15HK475-R- 15 4.7 1.0 10 12 8 16 12 12 R CWR15HK106-A- 15 10 1.5 15 18 10 20 15 12 A CWR15JK474-L- 20 .47 .5 5 6 6 12 9 24 L CWR15JK335-R- 20 3.3 .5 5 6 8 16 12 18 R CWR15KK334-L- 25 .33 .5 5 6 6 12 9 30 L 1/ Complete PIN shall include additional symbols to indicate capacitance tolera

18、nce, product level designator, and surge current option letter. If surge current is not required, the last “-“ shall be replaced with the letter Z. 2/ The following PINs are no longer available: CWR15CK107-F, CWR15DK686-F, CWR15FK336-F, CWR15HK105-L, CWR15HK156-F, CWR15JK685-A, CWR15JK106-F, CWR15KK

19、155-R, CWR15KK335-A, CWR15KK475-F, CWR15MK224-L, CWR15MK474-R, CWR15MK105-A, CWR15MK225-F, CWR15NK104-L, CWR15NK334-R, CWR15NK155-F, CWR15NK684-A. For historical information, use the ASSIST Online database at https:/assist.dla.mil. Changes from previous issue: The margins of this specification are m

20、arked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document b

21、ased on the entire content irrespective of the marginal notations and relationship to the last previous issue.” Custodians: Preparing activity: Army - CR Army - CR Navy - EC Air Force - 85 Agent: DLA - CC DLA - CC NASA - NA (Project 5910-2012-016) Review activities: Army - AR, MI Navy - AS, MC, OS,

22、SH Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-