ARMY MIL-PRF-55365 8 H-2011 CAPACITORS CHIP FIXED TANTALUM POLARIZED ESTABLISHED RELIABILITY NON-ESTABLISHED RELIABILITY AND HIGH RELIABILITY STYLE CWR11 (METRIC).pdf

1、 MIL-PRF-55365/8H SUPERSEDING 26 January 2011 MIL-PRF-55365/8G 22 February 2008 PERFORMANCE SPECIFICATION SHEET CAPACITORS, CHIP, FIXED, TANTALUM, POLARIZED ESTABLISHED RELIABILITY, NON-ESTABLISHED RELIABILITY AND HIGH RELIABILITY, STYLE CWR11 (METRIC) This specification is approved for use by all D

2、epartments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification and MIL-PRF-55365. FIGURE 1. Style CWR11 (molded) capacitors. AMSC N/A FSC 5910 DISTRIBUTION STATEMENT AApproved for public release, distribution is u

3、nlimited. METRIC Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55365/8H 2 Dimensions Case code H H2(min) L P 0.3 (.012) W W20.1 (.004) (see note 4) A 1.6 .2 (.063 .008)

4、0.7 (.028) 3.2 .2 (.126 .008) 0.8 (.031) 1.6 .2 (0.063 .008) 1.2 (.047) B 1.9 .2 (.075 .008) 0.7 (.028) 3.5 .2 (.138 .008) 0.8 (.031) 2.8 .2 (.110 .008) 2.2 (.087) C 2.5 .3 (.098 .012) 1.0 (.039) 6.0 .3 (.236 .012) 1.3 (.051) 3.2 .3 (.126 .012) 2.2 (.087) D 2.8 .3 (.110 .012) 1.0 (.039) 7.3 .3 (.287

5、 .012) 1.3 (.051) 4.3 .3 (.169 .012) 2.4 (.094) NOTES: 1. Dimensions are in millimeters. Inch equivalents are given in parenthesis for general information only. 2. These capacitors are designed for mounting by dip or wave soldering, reflow soldering, thermo-compression bonding, or other conventional

6、 means. 3. The anode (+) terminal shall be indicated by a marking on the case or by bevel on anode end. 4. Applicable to solderable surfaces only. The configuration of the nonsolderable area is optional. 5. Solderable surfaces are only those surfaces designated as such. Termination edges are not con

7、sidered solderable. 6. For solder coated terminations, add an additional 0.38 mm (.015 inch) to the tolerances for “L”, “W”, “H”, “P”, “W2”, and “H2” for each case size. FIGURE 1. Style CWR11 (molded) capacitors- Continued. REQUIREMENTS: Dimensions and configuration: See figure 1. Termination finish

8、: In accordance with MIL-PRF-55365. DC rated voltage: See table I. Above +85C, voltage derating is required (see MIL-PRF-55365). Operating temperature range: -55C to +125C. Product level designator: In accordance with MIL-PRF-55365. DC leakage (DCL): See table I. Capacitance: See table I. Capacitanc

9、e tolerance: 5 percent (J), 10 percent (K), or 20 percent (M). Dissipation factor (DF): See table I. Equivalent series resistance (ESR) at 100 kHz: In accordance with MIL-PRF-55365. See table I. Resistance to soldering heat: In accordance with MIL-PRF-55365. Copyright Communications - Electronics Co

10、mmand Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55365/8H 3 * Stability at low and high temperatures: In accordance with MIL-PRF-55365. * Life: * 2,000 hours: In accordance with MIL-PRF-55365. * 10,000 hours: In a

11、ccordance with MIL-PRF-55365. Solderability will be in accordance with MIL-PRF-55365 except that following steam aging; test samples may have a 30 minute bake out at 150C prior to solder dipping. Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo r

12、eproduction or networking permitted without license from IHS-,-,-MIL-PRF-55365/8H 4 TABLE I. Style CWR11 characteristics. Part or identifying number (PIN) DC rated Cap. DC Leakage (max) Dissipation factor (max) Max ESR 100 kHz Case 1/ voltage (+85C) (nom) +25C +85C +125C +25C +85C +125C -55C +25C si

13、ze Volts F A A % A % % Ohms CWR11C-225- 4 2.2 0.5 5.0 6.0 6 9 9 8.0 A CWR11C-475- 4 4.7 0.5 5.0 6.0 6 9 9 8.0 A CWR11C-685- 4 6.8 0.5 5.0 6.0 6 9 9 5.5 B CWR11C-106- 4 10.0 0.5 5.0 6.0 6 9 9 4.0 B CWR11C-156- 4 15.0 0.6 6.0 7.2 6 9 9 3.5 B CWR11C-336- 4 33.0 1.3 13.0 15.6 6 9 9 2.2 C CWR11C-686- 4 6

14、8.0 2.7 27.0 32.4 6 9 9 1.1 D CWR11C-107- 4 100.0 4.0 40.0 48.0 8 12 12 0.9 D CWR11D-155- 6 1.5 0.5 5.0 6 6 9 9 8.0 A CWR11D-225- 6 2.2 0.5 5.0 6 6 6 9 8.0 A CWR11D-335- 6 3.3 0.5 5.0 6 6 9 9 8.0 A CWR11D-475- 6 4.7 0.5 5.0 6 6 9 9 5.5 B CWR11D-685- 6 6.8 0.5 5.0 6 6 6 9 4.5 B CWR11D-106- 6 10.0 0.6

15、 6.0 7.2 6 9 9 3.5 B CWR11D-156- 6 15.0 0.9 9.0 10.8 6 6 9 3.0 C CWR11D-226- 6 22.0 1.4 14.0 16.8 6 9 9 2.2 C CWR11D-476- 6 47.0 2.8 28.0 33.6 6 6 9 1.1 D CWR11D-686- 6 68.0 4.3 43.0 51.6 6 9 9 0.9 D CWR11F-105- 10 1.0 0.5 5.0 6.0 4 6 6 10.0 A CWR11F-155- 10 1.5 0.5 5.0 6.0 6 6 9 8.0 A CWR11F-225- 1

16、0 2.2 0.5 5.0 6.0 6 9 9 8.0 A CWR11F-335- 10 3.3 0.5 5.0 6.0 6 9 9 5.5 B CWR11F-475- 10 4.7 0.5 5.0 6.0 6 9 9 4.5 B CWR11F-685- 10 6.8 0.7 7.0 8.4 6 9 9 3.5 B CWR11F-156- 10 15.0 1.5 15.0 18.0 6 6 9 2.5 C CWR11F-336- 10 33.0 3.3 33.0 39.6 6 9 9 1.1 D CWR11F-476- 10 47.0 4.7 47.0 56.4 6 9 9 0.9 D CWR

17、11H-684- 15 0.68 0.5 5.0 6.0 4 6 6 12.0 A CWR11H-105- 15 1.0 0.5 5.0 6.0 4 6 6 10.0 A CWR11H-155- 15 1.5 0.5 5.0 6.0 6 9 9 8.0 A CWR11H-225- 15 2.2 0.5 5.0 6.0 6 9 9 5.5 B CWR11H-335- 15 3.3 0.5 5.0 6.0 6 8 9 5.0 B CWR11H-475- 15 4.7 0.7 7.0 8.4 6 9 9 4.0 B CWR11H-106- 15 10.0 1.6 16.0 19.2 6 8 9 2.

18、5 C CWR11H-226- 15 22.0 3.3 33.0 39.6 6 8 9 1.1 D CWR11H-336- 15 33.0 5.3 53.0 63.6 6 9 9 0.9 D CWR11J-474- 20 0.47 0.5 5.0 6.0 4 6 6 14.0 A CWR11J-684- 20 0.68 0.5 5.0 6.0 4 6 6 12.0 A CWR11J-105- 20 1.0 0.5 5.0 6.0 4 6 6 10.0 A CWR11J-155- 20 1.5 0.5 5.0 6.0 6 9 9 6.0 B CWR11J-225- 20 2.2 0.5 5.0

19、6.0 6 8 9 5.0 B CWR11J-335- 20 3.3 0.7 7.0 8.4 6 9 9 4.0 B See footnote at end of table. Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55365/8H 5 TABLE I. Style CWR11 ch

20、aracteristics- Continued. PIN DC rated Cap. DC Leakage (max) Dissipation factor (max) Max ESR 100 kHz Case 1/ voltage (+85C) (nom) +25C +85C +125C +25C +85C +125C -55C +25C size Volts F A A % A % % Ohms CWR11J-475- 20 4.7 1.0 10.0 12.0 6 8 9 3.0 C CWR11J-685- 20 6.8 1.4 14.0 16.8 6 9 9 2.4 C CWR11J-

21、156- 20 15.0 3.0 30.0 36.0 6 8 9 1.1 D CWR11J-226- 20 22.0 4.4 44.0 52.8 6 9 9 0.9 D CWR11K-334- 25 0.33 0.5 5.0 6.0 4 6 6 15.0 A CWR11K-474- 25 0.47 0.5 5.0 6.0 4 6 6 14.0 A CWR11K-684- 25 0.68 0.5 5.0 6.0 4 6 6 7.5 B CWR11K-105- 25 1.0 0.5 5.0 6.0 4 6 6 6.5 B CWR11K-155- 25 1.5 0.5 5.0 6.0 6 8 9 6

22、.5 B CWR11K-225- 25 2.2 0.6 6.0 7.2 6 9 9 3.5 C CWR11K-335- 25 3.3 0.9 9.0 10.8 6 8 9 3.5 C CWR11K-475- 25 4.7 1.2 12.0 14.4 6 9 9 2.5 C CWR11K-685- 25 6.8 1.7 17.0 20.4 6 9 9 1.4 D CWR11K-106- 25 10.0 2.5 25.0 30.0 6 8 9 1.2 D CWR11K-156- 25 15.0 3.8 38.0 45.6 6 9 9 1.0 D CWR11M-104- 35 0.10 0.5 5.

23、0 6.0 4 6 6 24.0 A CWR11M-154- 35 0.15 0.5 5.0 6.0 4 6 6 21.0 A CWR11M-224- 35 .22 0.5 5.0 6.0 4 6 6 18.0 A CWR11M-334- 35 .33 0.5 5.0 6.0 4 6 6 15.0 A CWR11M-474- 35 .47 0.5 5.0 6.0 4 6 6 10.0 B CWR11M-684- 35 .68 0.5 5.0 6.0 4 6 6 8.0 B CWR11M-105- 35 1.0 0.5 5.0 6.0 4 6 6 6.5 B CWR11M-155- 35 1.5

24、 0.5 5.0 6.0 6 8 9 4.5 C CWR11M-225- 35 2.2 0.8 8.0 9.6 6 8 9 3.5 C CWR11M-335- 35 3.3 1.2 12.0 14.4 6 8 9 2.5 C CWR11M-475- 35 4.7 1.7 17.0 20.4 6 8 9 1.5 D CWR11M-685- 35 6.8 2.4 24.0 28.8 6 9 9 1.3 D CWR11N-104- 50 .10 0.5 5.0 12 6 8 8 22.0 A CWR11N-154- 50 .15 0.5 5.0 6.0 4 6 6 17.0 B CWR11N-224

25、- 50 .22 0.5 5.0 6.0 4 6 6 14.0 B CWR11N-334- 50 .33 0.5 5.0 6.0 4 6 6 12.0 B CWR11N-474- 50 .47 0.5 5.0 6.0 4 6 6 8.0 C CWR11N-684- 50 .68 0.5 5.0 6.0 4 6 6 7.0 C CWR11N-105- 50 1.0 0.5 5.0 6.0 4 6 6 6.0 C CWR11N-155- 50 1.5 0.8 8.0 9.6 6 8 9 4.0 D CWR11N-225- 50 2.2 1.1 11.0 13.2 6 8 9 2.5 D CWR11

26、N-335- 50 3.3 1.7 17.0 20.4 6 9 9 2.0 D CWR11N-475- 50 4.7 2.4 24.0 28.8 6 9 9 1.5 D 1/ Complete PIN shall include additional symbols to indicate termination finish, capacitance tolerance, product level, and, if applicable, surge current option letter. If optional surge current is not required, the

27、last “-“ shall be deleted. Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55365/8H 6 Marking: In accordance with MIL-PRF-55365, to be marked on top of case as follows: Pr

28、int orientation is optional. Case code A Case codes B, C, and D J (+) polarity stripe, J = JAN J (+) polarity stripe, J = JAN 105X - capacitance in picofarad code 105 - capacitance in picofarad code manufacturers identifier 35X - rated voltage; manufacturers identifier Alternate case code A marking

29、X (+) polarity stripe, X = manufacturers identifier 105J - capacitance in picofarad code; J = JAN At the option of the manufacturer, the lot date code may be marked on the top of the case for any case code. NOTES: Reference documents. This specification sheet references the following document. MIL-P

30、RF-55365 (Copies of this document is available online at https:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094). Changes from previous issue. The margins of this specification are marked with asterisks to indicate whe

31、re changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective o

32、f the marginal notations and relationship to the last previous issue. Custodians: Preparing activity: Army - CR Army - CR Navy - EC Air Force - 85 Agent: DLA - CC DLA - CC Review activities: (Project 5910-2011-007) Army - AR, MI Navy - AS, MC, OS, SH Air Force - 19, 99 NASA NA NOTE: The activities l

33、isted above were interested in this document as of the date of this document. Since organizations and responsibilities change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/ . Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-