ARMY MIL-PRF-55514 12 E-2013 CAPACITORS FIXED METALLIZED PLASTIC DIELECTRIC DC IN NONMETAL CASES ESTABLISHED RELIABILITY STYLE CFR29.pdf

1、AMSC N/A FSC 5910 INCH-POUND MIL-PRF-55514/12E 6 September 2013 SUPERSEDING MIL-PRF-55514/12D 18 October 2005 PERFORMANCE SPECIFICATION SHEET CAPACITORS, FIXED, METALLIZED PLASTIC DIELECTRIC, DC, IN NONMETAL CASES, ESTABLISHED RELIABILITY, STYLE CFR29 The specification sheet is approved for use by a

2、ll Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-55514. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information. FIGURE 1. Configuration and

3、dimensions. Inches mm .002 .015 .032 .040 .062 .300 1.500 0.05 0.38 0.81 1.02 1.57 7.62 38.10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55514/12E 2 REQUIREMENTS: Design and construction: Dimensions and configuration: See figure 1. Case:

4、 Non-hermetic. Dielectric: Normally polyphenylene sulfide (characteristic U) or metallized polycarbonate (characteristic R). Characteristics: R or U. Capacitance value: See table I. Capacitance tolerance: See table I. Operating temperature range: -55C to +85C, when properly voltage derated (see figu

5、re 2), characteristic R and U capacitors will operate to +125C. Voltage rating: See table I. Preconditioning: Not applicable. Burn-in: In accordance with MIL-PRF-55514 except for the following conditions: a. DC burn-in voltage shall be 140 percent of the dc rated voltage applied for 48 hours minimum

6、 at +125C, +4C, -0C. b. AC burn-in: Not applicable. Insulation resistance: Insulation resistance shall be measured at rated voltage at the applicable temperature. Charge time 2 minutes maximum; however, for capacitance values greater than 1.0 F, an additional 1 minute per F is permitted. The followi

7、ng limits shall apply: Temperature Insulation resistance +25C 50,000 +85C 5,000 +125C 500 Marking: In accordance with MIL-PRF-55514. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55514/12E 3 TABLE I. Capacitor characteristics and dimensions

8、. Part or identifying number (PIN) 1/ Capacitance F Capacitance tolerance Rated voltage at +85C volts, dc ESR milliohms at 100 kHz Ripple current max at +25C Resonant frequency kHz Dimensions T 2/ 4/ W 2/ 4/ H 3/ 4/ CFR29R-A106- CFR29R-A206- CFR29R-A506- 10.0 20.0 50.0 J, K, M J, K, M J, K, M 50 50

9、50 11 10 6 12.6 14.8 23.5 318 214 130 .562 .718 1.000 .862 .968 1.375 .750 .875 1.000 CFR29R-G305- CFR29R-G505- CFR29R-G106- CFR29R-G206- CFR29R-G506- 3.0 5.0 10.0 20.0 50.0 J, K, M J, K, M J, K, M J, K, M J, K, M 75 75 75 75 75 15 13 12 11 6 10.3 11.6 13.5 16.5 24.2 672 427 301 205 120 .468 .500 .7

10、18 .937 1.312 .718 .750 1.031 1.312 1.687 .750 .875 .875 1.000 1.250 CFR29R-B305- CFR29R-B505- CFR29R-B106- CFR29R-B206- CFR29R-B506- 3.0 5.0 10.0 20.0 50.0 J, K, M J, K, M J, K, M J, K, M J, K, M 100 100 100 100 100 15 13 12 11 6 10.6 12.4 14.6 17.1 23.6 684 427 290 192 115 .437 .593 .781 .906 1.43

11、7 .750 .906 1.093 1.281 1.812 .875 .875 1.000 1.250 1.375 1/ The complete PIN will include additional symbols to indicate, characteristic (U or R), capacitance tolerance, and product level (C, M, P, R, or S). 2/ Tolerances: Thickness and width +.062 inch, -.156 inch (+1.57 mm, -3.96 mm) on .437 inch

12、 through .500 inch (11.10 mm through 12.7 mm) and +.093 inch, -.187 inch (+2.36 mm, -4.75 mm) on .562 inch (14.27 mm) and greater. 3/ Tolerances: Length +.093 inch, -.062 inch (+2.36 mm, -1.57 mm). 4/ See dimension table below: Inches mm Inches mm Inches mm .437 .468 .500 .562 .593 .718 .750 .781 11

13、.10 11.89 12.70 14.27 15.06 18.24 19.05 19.84 .862 .875 .906 .937 .968 1.000 1.031 1.093 21.89 22.23 23.01 23.80 24.59 25.40 26.19 27.76 1.250 1.281 1.312 1.375 1.437 1.687 1.812 31.76 32.54 33.32 34.93 36.50 42.85 46.02 Provided by IHSNot for ResaleNo reproduction or networking permitted without li

14、cense from IHS-,-,-MIL-PRF-55514/12E 4 FIGURE 2. Voltage derating with temperature. Changes from previous issue: The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assume

15、s no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Preparing activity: Army

16、- CR Army - CR Navy - EC Air Force - 85 Agent: DLA - CC DLA - CC Review Activities: (Project 5910-2013-024) Navy - AS, MC, OS Air Force - 19 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-