ARMY MIL-PRF-55514 9 C-2013 CAPACITORS FIXED METALLIZED PLASTIC DIELECTRIC DC IN NONMETAL CASES ESTABLISHED RELIABILITY STYLE CFR13 AND CFR14.pdf

1、AMSC N/A FSC 5910 INCH-POUND MIL-PRF-55514/9C 6 September 2013 SUPERSEDING MIL-PRF-55514/9B 18 October 2005 PERFORMANCE SPECIFICATION SHEET CAPACITORS, FIXED, METALLIZED PLASTIC DIELECTRIC, DC, IN NONMETAL CASES, ESTABLISHED RELIABILITY, STYLE CFR13 AND CFR14 This specification sheet is approved for

2、 use by all Departments and and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-55514. FIGURE 1. Style CFR13 capacitors. FIGURE 2. Style CFR14 capacitors. NOTES: 1. Dimensions are in inches. 2. M

3、etric equivalents are given for general information only. Inches mm .002 .005 .032 .156 .312 .360 1.750 0.05 0.13 0.81 3.96 7.93 9.14 44.45 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Capacitor characteristics. Characteristic L, style CF

4、R13 capacitors Part or identifying number (PIN) 1/ Capacitance nominal DC rated voltage (at +105C) Capacitance tolerance available D L .062(1.57) M 2/ ESR Ohms 20 - 100 kHz Max Maximum ripple current (AMPS RMS) 20-100 kHz case temperature +25C +35C +45C +55C +65C +75C +85C CFR13ALB105- 1.0 100 J, K,

5、 M .469 (11.91) .062 (1.57) .750 (19.05) .032 (0.81) .015 9.2 8.5 7.8 7.0 6.0 4.9 4.5 CFR13ALB205- 2.0 100 J, K, M .534 (13.56) .062 (1.57) .938 (23.81) .032 (0.81) .012 10.8 10.0 9.1 8.2 7.0 5.8 5.3 CFR13ALB305- 3.0 100 J, K, M .624 (15.85) .093 (2.36) .938 (23.81) .040 (1.02) .011 12.1 11.2 10.3 9

6、.2 8.0 6.5 5.9 CFR13ALB505- 5.0 100 J, K, M .640 (16.26) .093 (2.36) 1.250 (31.75) .040 (1.02) .010 13.8 12.7 11.6 10.4 9.0 7.4 6.7 CFR13ALB106- 10.0 100 J, K, M .805 (20.45) .093 (2.36) 1.500 (38.10) .040 (1.02) .009 15.0 15.0 14.2 12.7 11.0 9.0 8.2 CFR13ALB206- 20.0 100 J, K, M .875 (22.23) .125 (

7、3.18) 2.250 (57.15) .040 (1.02) .008 15.0 15.0 15.0 15.0 13.6 11.1 10.0 CFR13ALB306- 30.0 100 J, K, M 1.075 (27.31) .125 (3.18) 2.250 (57.15) .040 (1.02) .006 15.0 15.0 15.0 15.0 15.0 12.4 11.4 CFR13ALC105- 1.0 200 J, K, M .450 (11.43) .062 (1.57) 1.250 (31.75) .032 (0.81) .020 7.3 7.3 7.3 7.3 7.2 5

8、.9 5.4 CFR13ALC205- 2.0 200 J, K, M .605 (15.37) .093 (2.36) 1.250 (31.75) .032 (0.81) .015 12.0 12.0 11.3 10.1 8.7 7.1 6.5 CFR13ALC305- 3.0 200 J, K, M .654 (16.61) .093 (2.36) 1.500 (38.10) .040 (1.02) .013 15.0 13.8 12.6 11.3 9.8 8.0 7.3 CFR13ALC505- 5.0 200 J, K, M .769 (19.53) .093 (2.36) 1.750

9、 (44.45) .040 (1.02) .011 15.0 15.0 14.7 13.1 11.4 9.3 8.5 CFR13ALC106- 10.0 200 J, K, M .905 (22.99) .125 (3.18) 2.250 (57.15) .040 (1.02) .009 15.0 15.0 15.0 15.0 13.8 11.3 10.3 CFR13ALC206- 20.0 200 J, K, M 1.315 (33.40) .125 (3.18) 2.250 (57.15) .040 (1.02) .006 15.0 15.0 15.0 15.0 15.0 14.1 12.

10、8 CFR13ALE105- 1.0 400 J, K, M .620 (15.75) .093 (2.36) 1.500 (38.10) .040 (1.02) .019 9.5 9.5 9.5 9.5 9.5 7.8 7.1 CFR13ALE205- 2.0 400 J, K, M .802 (20.37) .093 (2.36) 1.750 (44.45) .040 (1.02) .015 15.0 15.0 15.0 13.4 11.6 9.5 8.7 CFR13ALE305- 3.0 400 J, K, M .961 (24.41) .125 (3.18) 1.750 (44.45)

11、 .040 (1.02) .012 15.0 15.0 15.0 15.0 13.1 10.7 9.8 CFR13ALE505- 5.0 400 J, K, M 1.067 (27.10) .125 (3.18) 2.250 (57.15) .040 (1.02) .010 15.0 15.0 15.0 15.0 15.0 12.5 11.4 CFR13ALE106- 10.0 400 J, K, M 1.543 (39.19) .125 (3.18) 2.250 (57.15) .040 (1.02) .006 15.0 15.0 15.0 15.0 15.0 15.0 14.1 See f

12、ootnotes at end of table. MIL-PRF-55514/9C2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Capacitor characteristics - Continued. Characteristic L, style CFR14 capacitors Part or identifying number (PIN) 1/ Capacitance nominal DC rated volta

13、ge (at +105C) Capacitance tolerance available D L .078(1.98) L1 0.62(1.57) ESR Ohms 20 - 100 kHz Max Maximum ripple current (AMPS RMS) 20-100 kHz case temperature +25C +35C +45C +55C +65C +75C +85C CFR14LLB105- 1.0 100 J, K, M .469 (11.91) .062 (1.57) .922(23.42) 1.640(41.66) .015 10.3 9.5 8.7 7.8 6

14、.7 5.5 5.0 CFR14LLB205- 2.0 100 J, K, M .534 (13.56) .062 (1.57) 1.110(28.19) 1.828(46.43) .012 12.0 11.0 10.0 8.9 7.8 6.3 5.8 CFR14LLB305- 3.0 100 J, K, M .624 (15.85) .093 (2.36) 1.110(28.19) 1.828(46.43) .011 13.3 12.3 11.2 10.0 8.7 7.1 6.5 CFR14LLB505- 5.0 100 J, K, M .640 (16.26) .093 (2.36) 1.

15、422(36.12) 2.140(54.36) .010 14.8 13.7 12.5 11.2 9.7 7.9 7.2 CFR14LLB106- 10.0 100 J, K, M .805 (20.45) .093 (2.36) 1.672(42.47) 2.390(60.71) .009 17.8 16.5 15.0 13.5 11.7 9.5 8.7 CFR14LLB206- 20.0 100 J, K, M .875 (22.23) .125 (3.18) 2.422(61.52) 3.140(79.76) .008 21.6 20.0 18.3 16.4 14.2 11.6 10.6

16、 CFR14LLB306- 30.0 100 J, K, M 1.075 (27.31) .125 (3.18) 2.422(61.52) 3.140(79.76) .006 24.3 22.5 20.5 18.4 15.9 13.0 11.9 CFR14LLC105- 1.0 200 J, K, M .450 (11.43) .062 (1.57) 1.422(36.12) 2.140(54.36) .020 7.3 7.3 7.3 7.3 7.2 6.4 5.8 CFR14LLC205- 2.0 200 J, K, M .605 (15.37) .093 (2.36) 1.422(36.1

17、2) 2.140(54.36) .015 14.3 13.3 12.1 10.8 8.7 7.7 7.0 CFR14LLC305- 3.0 200 J, K, M .654 (16.61) .093 (2.36) 1.672(42.47) 2.390(60.71) .013 15.9 14.7 13.5 12.0 9.8 8.5 7.8 CFR14LLC505- 5.0 200 J, K, M .769 (19.53) .093 (2.36) 1.922(48.82) 2.640(67.06) .011 18.3 17.0 15.5 13.9 11.4 9.8 8.9 CFR14LLC106-

18、 10.0 200 J, K, M .905 (22.99) .125 (3.18) 2.422(61.52) 3.140(79.76) .009 22.4 20.7 18.9 16.9 13.8 12.0 10.9 CFR14LLC206- 20.0 200 J, K, M 1.315 (33.40) .125 (3.18) 2.422(61.52) 3.140(79.76) .006 27.4 25.4 23.2 20.7 15.0 14.7 13.4 CFR14LLE105- 1.0 400 J, K, M .620 (15.75) .093 (2.36) 1.672(42.47) 2.

19、390(60.71) .019 9.5 9.5 9.5 9.5 9.5 8.3 7.5 CFR14LLE205- 2.0 400 J, K, M .802 (20.37) .093 (2.36) 1.922(48.82) 2.640(67.06) .015 15.0 15.0 15.0 14.2 11.6 10.0 9.1 CFR14LLE305- 3.0 400 J, K, M .961 (24.41) .125 (3.18) 1.922(48.82) 2.640(67.06) .012 21.1 19.5 17.8 15.9 13.1 11.3 10.3 CFR14LLE505- 5.0

20、400 J, K, M 1.067 (27.10) .125 (3.18) 2.422(61.52) 3.140(79.76) .010 24.4 22.6 20.6 18.5 15.0 13.1 11.9 CFR14LLE106- 10.0 400 J, K, M 1.543 (39.19) .125 (3.18) 2.422(61.52) 3.140(79.76) .006 30.0 27.8 25.4 22.7 15.0 16.1 14.7 1/ The completePIN will include additional symbols to indicate capacitance

21、 tolerance and product level (C, M, P, R, and S). 2/ Comparable AWG sizes are No. 20 AWG (.032 inch (0.81 mm) and No. 18 AWG (.040 inch (1.02 mm).3MIL-PRF-55514/9CProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55514/9C 4 REQUIREMENTS: Dimens

22、ions and configuration: See figure 1, figure 2, and table I. Case: Non-hermetic. Dielectric: Normally polypropylene, metallized. Capacitance (cap.) value: See table I. Capacitance tolerance: See table I. Rated voltage: See table I. Operating temperature range: -55C to +105C for dc operation. Product

23、 level: Non-established reliability - C; Established reliability - M, P, R or S. Preconditioning: Not applicable. Burn-in: In accordance with MIL-PRF-55514 except for the following conditions: a. DC burn-in voltage shall be 140 percent of the dc rated voltage applied for 48 hours minimum at +105C, +

24、4C, -0C. b. AC burn-in: Not applicable. Dielectric withstanding voltage (DWV): In accordance with MIL-PRF-55514, except charge time 2 minutes maximum at 200 percent rated dc voltage. Insulation resistance: In accordance with MIL-PRF-55514, except test voltage shall be 100 V dc. Dissipation factor (D

25、F): Not more than 0.1 percent when measured in accordance with MIL-PRF-55514. Low temperature conditioning and capacitance change with temperature: In accordance with MIL-PRF-55514. Resistance to soldering heat: Method 210 of MIL-STD-202, condition B. Cap: Maximum of 0.25 percent. Life (at 105C): In

26、 accordance with MIL-PRF-55514. Accelerated condition: 140 percent of +105C rated voltage. Rated condition: 100 percent of +105C rated voltage. IR (at +25C terminal to terminal): Not less than 50.0 percent of initial requirement. Cap (at +25C): Maximum of 1.0 percent. DF (at +25C) after life: .12 pe

27、rcent maximum. AC conditioning: In accordance with MIL-PRF-55514. AC conditioning for qualification shall be at the rated ac ripple current at +85C and 40 kHz. For group B testing, rated ac ripple current at +85C and 40 kHz shall be run on test samples in accordance with table II herein at 12-month

28、intervals. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55514/9C 5 TABLE II. AC conditioning test samples. 1/ Each test sample shall contain at least one capacitor of the highest and lowest capacitance value of each voltage group manufactu

29、red during the 12-month period. Changes from previous issue: The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in th

30、ese notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-PRF-55514, this document references MIL-STD-202.

31、 Custodians: Preparing activity: Army - CR Army - CR Navy - EC Air Force - 85 Agent: DLA - CC DLA - CC Review activities: (Project 5910-2013-022) Navy - AS, MC, OS Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizatio

32、ns and responsibilities can change, you should verify the currency of the information above using ASSIST Online database at https:/assist.dla.mil. DC rated voltage (volts) Sample size Capacitance range for selection of sample 1/ (F) 100 200 400 24 24 24 1.0 to 30.0 1.0 to 20.0 1.0 to 10.0 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-