ARMY MIL-R-51015 C-1990 RIOT CONTROL AGENT CS CAPSULE (METRIC)《CS胶囊暴动控制介质(METRIC)》.pdf

1、MIL-R-5 10 15C (EA) 27 September 1990 SUPERSEDING 4 September 1987 MIL-R-5 101 5B(EA) MILITARY SPECIFICATION RIOT CONTROL AGENT, CS CAPSULE (METRIC) This specijlcation is approved for use by the US. Army Chemical Research, Development and Engineering Center, Department of the Army, and is available

2、for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers one type of capsule filled with Riot Control Agent, cs. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications,

3、stan- dards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the De- partment of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitat

4、ion (see 6.2). * I Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, U.S. Army Chemical Research, Development and Engineering Center, ATI“: SMCCR-PET-S, Aberdeen Proving Ground, MD 2 10

5、 10-5423 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 1365 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. 0 -. i Provided by IHSNot for ResaleNo reproductio

6、n or networking permitted without license from IHS-,-,-MIL-R-5 1 O 1 5C(EA) SPECIFICATIONS FEDERAL RR-S-366 - Sieve, Test u-c-115 - Capsule, Gelatin MILITARY MIL-R-51029 - Riot Control Agent, CS STANDARDS FEDERAL FED. TEST METHOD STD. NO. 101 - Test Procedures for Packaging Materials (Unless otherwi

7、se indicated, copies of federal and military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.1.2 Other Government documents, drawings, and publications. The following other Governme

8、nt documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicita- tion. U.S. ARMY CHEMICAL RESEARCH, DEVELOPMENT AND ENGINEERING CENTER SPECIAL PACKAGING INSTRUCTION (SPI) PML-R-51015 - Riot C

9、ontrol Agent, CS Capsule (Copies are available from Commander, U.S. Army Information Systems Command, ATTN: ASQNC-AM-CT, Rock Island, IL 61229-7300.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes

10、 precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Materials, 3.1.1 Capsule. The capsule shall conform to size O0 of U-C-115. 2 Provided by IHSNot for ResaleNo reproduction or networking permit

11、ted without license from IHS-,-,-c *. MIL-R-SLOLSC 13 M 7797906 0461873 7 M MIL-R-5 1 O 1 5 C (EA) 3.1.2 Riot Control Agent, CS. The Riot Control Agent, CS used to fill the capsule shall conform to MIL-R-51029 and shall be ground so that no less than i00 percent by weight passes through an 840-micro

12、meter (No. 20) sieve when tested as specified in 4.2.4.1. 3.2 Weight. The filled capsule shall weigh no less than 0.58 gram (8) when tested as specified in 4.2.4.2. 3.3 Workmanship. The filled capsule shall be free from interior or exterior contamina- tion such as dirt, grease, and oil. The filled c

13、apsule shall be free from damage such as cracks, dents, and punctures. The exterior of the capsule shall not be contaminated with Riot Control Agent, CS. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or pur- chase order, the contractor

14、is responsible for the performance of all inspection require- ments (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specif

15、ied herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. A

16、ll items shall meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the respon

17、sibility of ensuring that all products or supplies submitted to the Government for acceptance comply with all require- ments of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however, this does not authorize

18、 submission of known defective material, either indicated or actual, nor does it commit the Government to accept defective material. 4.1.2 Contractor assurance of compliance. The contractors quality program or de- tailed inspection system shall provide assurance of compliance of all characteristics

19、with the applicable drawing, special packaging instruction, and specification requirements using, as a minimum, the conformance criteria specified herein. 4.1.3 Alternative inspection provisions. Alternative inspection procedures, methods, or equipment, such as statistical process control, tool cont

20、rol, and other types of sampling procedures may be used by the contractor when they provide, as a minimum, the level of quality assurance required by the inspection provisions specified herein. Prior to applying such alternative procedures, methods, or equipment, the contractor shall describe them i

21、n a written proposal submitted to the Government for evaluation and approval. (See 6.3.) When 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-.i MIL-R-SLOLSC 13 U 9999906 0461894 9 U 3 MIL-R-5 1 O 1 5C (EA) required, the contractor shall demonstrat

22、e that the effectiveness of each proposed alterna- tive is equal to or better than the quality assurance provisions specified herein. In cases of dispute as to whether the contractors proposed alternative provides equal quality assurance, the provisions of this specification shall apply. All approve

23、d alternative inspec- tion provisions shall be specifically incorporated into the contractors quality program or detailed inspection system, as applicable. 4.2 Quality conformance inspection. 4.2.1 Lotting. A lot shall consist of the filled capsules offered for acceptance at one time which have been

24、 produced by one manufacturer, at one plant, during one 8-hour shift, from the same materials, under essentially the same manufacturing conditions. However, no more than one lot of Riot Control Agent, CS shall be used in one lot of filled capsules. 4.2.2 Sampling. TABLE I. Sampling Lot size 2 to 8 9

25、 to 15 16 to 25 26 to 50 51 to 90 91 to 150 151 to 280 281 to 500 501 to 1200 1201 to 3200 3201 to 10000 10001 to 35000 35001 to 150000 150001 to 500000 500001 and over I * * * * * * * * * 1250 1250 1250 1250 1250 1250 It * * * * * * * 315 315 315 315 315 490 715 715 Inspection levels and sample siz

26、es * * * * * 125 125 125 125 125 192 294 294 345 435 IV * * * * 50 50 50 50 75 116 116 135 170 200 244 V * * * 32 32 32 32 48 73 73 86 108 123 156 189 VI * * 20 20 20 20 20 47 47 53 68 77 96 119 143 VII * 13 13 13 13 13 20 29 34 42 50 60 74 90 102 * 8 8 8 8 12 19 21 27 35 38 46 56 64 64 Ix 5 5 5 5 7

27、 11 13 16 19 23 29 35 40 40 40 X 3 3 3 5 6 7 10 11 15 18 22 29 29 29 29 XI 2 2 3 5 5 6 7 9 11 13 15 15 15 15 15 *Xndicates one hundred percent inspection. If sample size exceeds lot size, perform one hundred percent inspection. Accept the lot represented on zero nonconforming characteristics and rej

28、ect the lot represented on one or more nonconforming characteristics for all inspection levels, 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-SLOLSC 13 m 77777Ob 04bL75 O = MIL-R-5 1 O 15 C (EA) 4.2.2.1 For examination and nondestructive te

29、sts. Sampling shall be conducted in ac- cordance with table I. Samples shall be selected at random. 4.2.2.2 For destructive tests. Fifty filled capsules shall be randomly selected from each lot. 4.2.3 Inspection procedure. Sample items and the packaging thereof shall be exam- ined and tested as spec

30、ified in 4.2.3.2 and 4.2.3.3. Failure of any sample item or packaging thereof to conform to any characteristic in the classification of characteristics or failure of the Riot Control Agent, CS in the filled capsules to meet the particle size requirement shall be cause for rejection of the lot repres

31、ented. 4.2.3.1 Inspection characteristics. Major characteristics are characteristics whose non- conformance to specified requirements is likely to result in failure or to reduce materially the usability of the item for its intended purpose. Minor characteristics are characteristics whose nonconforma

32、nce to specified requirements is not likely to reduce materially the op- eration or usability of the item for its intended purpose. 4.2.3.2 For examination and nondestructive tests. Sample filled capsules and the packaging thereof shall be examined in accordance with table I and the following classi

33、fica- tion of characteristics: (a) Riot Control Agent, CS Capsule. 9 Category Critical: Major 101 102 103 104 Minor 201 Sampling and Inspection Characteristic acceptance criteria method None defined Assembly No damage No interior contamination Weight No exterior contamination Table I, level V Table

34、I, level V Table I, level V Table I, level V Visual Visual Visual 4.2.4.2 Table I, level VI Visual 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Category Critical: Major 101 102 103 104 105 106 107 108 1 o9 110 (b) Packaging (SPI PMIL-R-51015). C

35、haracteristic None defined Unit pack container leakage Item completely clean and dry prior Contents per container evident and to unit packing correct Unit pack container and closure Exterior coating on cans evident and Side seam of can striped Tape closure for bottle evident and Packing container an

36、d closure evident Packing assembly evident and correct Marking evident, correct, and legible evident and correct correct . correct correct Sampling and acceptance criteria Table I, level IX Table I, level VI Table I, level VI Table I, level VI Table I, level VI Table I, level VI Table I, level VI Ta

37、ble I, level VI Table I, level VI Table I, level VI Inspection method 4.2.4.3 Visual Visual Visual Visual Visual Visual Visual Visual Visual 4.2.3.3 For destructive tests. The Riot Control Agent, CS in the filled capsules taken in 4.2.2.2 shall be tested as specified in 4.2.4.1. 4.2.4 Tests. Tests s

38、hall be conducted as follows: 4.2.4.1 Particle size. Weigh to the nearest 0.01 g approximately 8 g of the Riot Control Agent, CS and place into an 840-micrometer (No. 20) sieve conforming to RR-S-366 nested into a bottom pan. Cover the sieve and shake by hand for 3 minutes. Weigh the material in the

39、 bottom pan to the nearest 0.01 g. The difference between the initial and final weighings shall not exceed 0.03 g. 4.2.4.2 Weight. Weigh the filled capsule on a balance which has an accuracy of no less than 0.001 g. 4.2.4.3 Unit pack container leakage. The unit pack container (can) containing the Ri

40、ot Control Agent, CS shall not leak when tested in accordance with method 5009.2 of FED. TEST METHOD STD. NO. 101 using the hot water technique. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. MIL-R-51025C 13 = 7777706 0462897 Lt MIL-R-5 1 O 1 SC

41、(EA) 5. PACKAGING 5.1 Packaging. Packaging shall be as specified in SPI PMIL-R-51015. 6. NOTES (This section contains information of a general or explanatory nature that may be help- ful, but is not mandatory.) 6.1 Intended use. Riot Control Agent, CS Capsules are intended for use in the training of

42、 troops. 6.2 Acquisition requirements. Acquisition documents must specify the following: (a) Title, number, and date of this specification (b) Issue of DODISS to be cited in the solicitation, and if required, the specific (c) Level of packing required issue of individual documents referenced (see 2.

43、1.1) 6.3 Submission of alternative inspection provisions, Proposed alternative inspection provisions should be submitted by the contractor to the procuring contracting officer for evaluation and approval by the technical activity responsible for preparation of this specifi- cation. 6.4 Safety inform

44、ation on CS. For safety information on CS, see Hazardous Compo- nent Safety Data Statement (HCSDS) No. 20067. Copies are available from Commander, U.S. Army Information Systems Command, ATTN: ASQNC-ARI-CT, Rock Island, IL 61229-72 1 O. 6.5 International interest. Certain provisions of this Specifica

45、tion are the subject of international standardization agreement DCA-Army Quadripartite Standardization Agree- ment 427. When amendment, revision, or cancellation of this specification is proposed that will modify the international agreement concerned, the preparing activity will take appropri- ate a

46、ction through international standardization channels, including departmental standardi- zation offices, to change the agreement or make other appropriate accommodations. 6.6 Changes from previous issues. Marginal notations are not used in this revision to identify changes with respect to the previou

47、s issue due to the extensiveness of the changes. 6.7 Subject term (key word) listing. Particle size Weight 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-SLOLSC 13 Custodian: Army - EA MIL-R-5 1 O 1 5 C (EA) Preparing activity: Army - EA Project No. 1365-Al00 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-