ARMY MIL-S-40626 D-1994 SIGN KIT VEHICLE CLASS《车辆类别标志附件》.pdf

1、MIL-S-40626D m 9999906 L984LL 436 m MIL-S-40626D ( GL) 31 March 1994 SUPERSEDING MIL-S-40626C (CL) 7 March 1978 MILITARY SPECIFICATION SIa KIT, VMICZE CLASS This specification is approved for use by the Natick Research, Developnt, and Engineering Center, Department of the Army, and is available for

2、use by all Departments and Agencies of the Department of Defense. 1. SOOPE 1.1 Sco. This specification covers one type and size of vehicle class sign kit. 2. APPLICABLE IxxDmws 2.1 Gavenmient documents. 2.1.1 spec ifications, stanurds, and handbooks. The following specifica- Unless otherwise specifi

3、ed, the issues of these documents tions, standards, and handbooks form a part of this document to the extent specified herein. are those listed in the issue of the Departmnt of Defense Index of Specifications and Standards (DISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICA

4、TIONS A-A-1898 - Cushioning Material, Cellulosic, Packaging Beneficial ccarments (recomtmdations, additions, deletions), and any pertinent data which may be used in improving this document should be addressed to: Center, Natick, MA 01760-5017, by using the Standardization Dccumnt Improvement Proposa

5、l (DD Form 1426) appearing at the end of this document or by letter. U.S. Army Natick Research, Developirent, and Engineering AM32 N/A FSC 9905 DISIFUBUTIN STATEMENT A. Approved for pblic release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without

6、 license from IHS-,-,-IIL-S-4062bD N 9999906 L849L2 372 N QQ-A-225/3 - Aluminum Alloy Bar, and Wire; Rolled, Drawn, QQ-A-250/8 - Aluminum Alloy 5052, Plate and Sheet QQ-S-698 - Steel Sheet and Strip, m carbon TT-C-490 - Cleaning Methods for Ferrous Surfaces and TI-P-1757 - Primer Coating, Zinc Chrcs

7、Mte, Low-Moisture- or Cold Finished, 2011 Retreatments for Organic Coatings Sens i tivi ty PPP-B-636 - Boxes, Shipping, Fiberboard MILITARY MIL-C-5541 - Chemical Conversion Coatings on Aluminum anci MIL-C-53039 - Coating, Aliphatic Polyurethane, Single Catpnent, Aluminum Alloys Chmical Agent Resista

8、nt FED-SID-105 - Colors Used in Govemnt Procurement MILITARY MIL-SID-105 - Sampling Procedures and Tables for Inspection by Attributes MIL-Sill-129 - Marking for Shipnt and Storage MIL-Siil-147 - Palletized Unit imds (Mess otherwise indicated, copies of federal and military specifications, standards

9、, and handbooks are available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.1.2 Other Govemnt documents, drawinqs, and publications. The following other Government documents, drawings, and publications form a part of this document to

10、the extent specified herein. the issues are those cited in the solicitation. Unless otherwise specified, DRAWINGS U.S. ARMY IWTICK RESE“, D!3VETBPMJZNT, AND ENGINEERING CENTER 6-1-2248 - Sign Kit, Vehicle Class; Assembly and Detail (Copies of drawinqs are available from the U.S. Army Natick Research

11、, Develpnent, and Engineering Center, AI“: SATNC-MII; Natick, MA 01760- 5017. ) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-40b2bD m 999990b 1784913 209 m MIL-S-40626D( CL) 2.2 Non-Govemnt uublications. The follawing dommnt forms a part o

12、f Unless otherwise specified, this document to the extent specified herein. the issues of the documents which are XlD adopted are those listed in the issue of the DODISS cited in the solicitation. the issues of documents not listed in the DCDISS are the issues of the documents cited in the solicitat

13、ion (see 6.2). Unless otherwise specified, AMERICAN SOCIETY FOR TESTING AND MATERIAIS (ASIM) D 3951 - Standard Practice for Carmercial Packing (Application for copies should be addressed to the Amxican Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) (Non-Govemmnt s

14、tarsdards and other pblications are normally available fran the organizations that prepare or distribute the documente. documents also may be available in or thnxigh libraries or other infornia- tional services.) These 2.3 Order of precedence. In the event of a conflict between the text of this docu

15、ment and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exaption has been obtained. 3.1 First article. When specified (see 6.2), a sqle shall be subjected to first article inspec

16、tion (see 6.3) in accordance with 4.3. 3.2 Materials and commnents. The materials and canponents shall be as specified herein and as shown on the applicable drawing. ccmponents not definitely specified shall be of the quality nonnally used by the nianufacturer provided the canpleted item canplies wi

17、th all the provisions of this document. practical as long as it meets the requimnts of this specification. Materials and It is encouraged that recycled material be used when 3.2.1 Aluminum. 3.2.1.1 Plate and sheet. The aluminum alloy plate and sheet shall be as specified in QQ-A-250/8. 3.2.1.2 Bar,

18、rcd and wire. The aluminum alloy bar, rod and wire shall conform to temper T3 of QQ-A-225/3. 3.2.2 Steel, sheet and striD. The steel sheet shall conform to cold rolled or hot rolled, camnercial quality, and the steel strip shall conform to any temper, condition and edge of QQ-S-698. 3.2.3 CD screws,

19、 washers and nuts. Cap screws, washers and nuts shall conform to the requirements shown on Drawing 6-1-2248. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-40626D (GL) 3.2.4 Primer. The primer shall be as specified in TT-P-1757 with canposit

20、ion and color optional. 3.2.5 Coatinq. The coating shall be as specified in MIL-C-53039. 3.3 Construction. The sign kit shall confoxm in all respects to Drawing 6-1-2248 and as specified herein. 3.3.1 Disk. The disk shall be fabricated of aluminum alloy, temper O, as specified in 3.2.1.1. 3.3.2 Anch

21、or pin and pin lock. The anchor pin and pin lock shall be fabricated of aluminum alloy specified in 3.2.1.2. shall not be loose. The pins, after assembly, 3.3.3 Plates, retaininq and numeral. The retaining and numeral plates shall be fabricated of aluminum alloy, temper H38, as specified in 3.2.1.1.

22、 The numeral and retaining plates shall be inserted in position and shall not becane loose or fall out due to vibration when tested as specified in 4.4.5. Prepainted aluminum sheet for numeral plates may be furnished and shall confoxm to the manufacturers standard ccmnercial practice. color shall be

23、 Dark Green 34082, as specified in 3.2.5. The background 3.3.4 Brackets, universal, lonq and short. The brackets shall be . fabricated of steel as specified in 3.2.2 and shall be of the design as shown on Drawing 6-1-2248. 3.4 Finish. Except when prepainted sheet is used, the sign kit shall be finis

24、hed as specified herein. 3.4.1 Surface mewration. All surfaces and edges of the disk, retaining plate, and numeral plates shall be prepared for painting in accordance with class lA of MIL-C-5541. accordance with any method of TILC-490. The brackets shall be prepared for painting in 3.4.2 Priming. Al

25、l prepared surfaces and edges of disks, retaining plate, and numeral plates shall be coated with the primer specified in 3.2.4. 3.4.3 Coatinq. retaining plate, steel brackets, and numeral plates shall be coated as specified in 3.2.5. After drying, the prirned surfaces and edges of the disk, 3.4.4 Ch

26、aracters. The letter “C“ and the numerals shall be gothic type and shall be applied to the retaining plate and numeral plates, respectively, after the background color specified in 3.3.3 has been applied. The letter “C“ and the numrals shall be clear and sharply defined. requirements for the charact

27、ers shall be as specified in table I. Additional 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-UIL-S-4062bD H 99999Ob 1984915 081 MIL-C-40626D( CL) TABLE I. Additional character rau irements Requi-t Letter Numerals Height 2 inch minimum 3-1/2 inc

28、h minimum 2-5/8 inch maximum 3-5/8 inch maximum Width of 7/16 inch minimum 9/16 inch minimum stroke 9/16 inch maximum 11/16 inch maximum Color (see 3.2.5) Aircraft Red 31136 Black 37030 Data Utter “C“ centered One side ODPO site side on one side of the O 1 4 5 retaining plate only 2 3 6 7 8 9 3.5 Ma

29、rkinu for identification. Each sign kit disk shall be permanently and legibly marked on the back side with the manufacturers name or readily identifiable trademark. 3.6 WorloMnship. The end item shall conform to the quality of product established by this Specification. All edges shall be rounded or

30、beveled and all surfaces and edges shall be free from hms, slivers and sharp edges. The finish of the disks, retaining plate, numeral plates, brackets, lettering and numerals shall be free frcm imbedded foreign matter, uncoated areas, cracks, blisters, flakes, scratches, mars, sags and rum. The lett

31、ering shall be smooth, even, straight and perpendicular to the base. 4. QUALITY AssuRApJ(=E PIIDVISIONS 4.1 Responsibility for insmion. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requimnts (examinations and tests)

32、 as specified herein. Except as otherwise specified in the contract or purchase order, the contractor my use his own or any other facilities suitable for the prfom- ance of the inspection requirements specified herein, unless disapproved by the Goverriment. inspection set forth in this specification

33、 where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. The Govenrment reserves the right to perfom any of the 4.1.1 Responsibility for canpliance. All itenr; shall meet all requirements of sections 3 and 5. specification shall becane a part o

34、f the contractors overall inspection system or quality progrm. specification shall not relieve the contractor of the responsibility of The inspection set forth in this The absence of any inspection requirements in the 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without lic

35、ense from IHS-,-,-MIL-S-40bZbD m 99999Ob L9849Lb TLB W ensuring that all products or supplies suhnitted to the Govemnt for acceptance canply with all requirements of the contract. inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements, hae

36、ver, this does not authorize sutmission of known defective material, either indicated or actual, nor does it cornnit the Govemnt to accept defective material. Sampling 4.1.2 Responsibility for dimensional requirements. Unless otherwise specified in the contract or purchase oder, the contractor is re

37、sponsible for ensuring that all specified dimensions have been met. When dimensions cannot be examined on the end item, inspection shall be made at any point, or at all points in the manufacturing process necessary to ensure ccanpliance with all dimensional requirements. 4.2 Classification of inspec

38、tions. The inspection requimnts specified herein are classified as follaws: a. b. First article inspection (see 4.3). Quality conformance inspection (see 4.4). 4.3 First article inspection. When a first article is required (see 3.1 and 6.2), it shall be examined for the defects specified in 4.4.3 an

39、d 4.4.4 and tested for the characteristics specified in 4.5.1. shall be cause for the rejection of the first article. Any nonconformance 4.4 Quality conformance inspection. Unless otherwise specified, sampling for inspection shall be performed in accordance with MIL-STD-105. 4.4.1 Camonent and mater

40、ial insuection. In accordance with 4.1, canponents anci materials shall be inspected in accordance with all the requirements of referenced docunients unless otherwise excluded, amended, modified, or qualified in this specification or applicable purchase document. 4.4.2 In-process inspection. When ap

41、plicable, inspection shall be made to determine that surface preparation and application of primr to the canpo- nents are in accordance with specified requirements of 3.4.1 and 3.4.2. Whenever nonconformance is noted, correction shall be made to the affected items and process. process. Items that ca

42、nnot be corrected shall be rexnoved from the 4.4.3 End item visual examination. The end items shall be examined for the defects listed in table II. sign kits. shall be I. the lot. The lot size shall be expressed in units of The sample unit shall be one sign kit. The inspection level The finding of a

43、ny defect shall be cause for the rejection of 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-40626D W 7799906 L9849L7 754 H MIL-S-40626D( GL) TABLE II. End item visual defects Examine Defect Classification Major Minor Finish (all canpo- Canp

44、onent not colors specified Cap screws, nuts and washers not zinc plated Coated surfaces not smooth, uniform or continuous uncoated areas Not free from cracks, blisters, nents) orange peel, flakes, sags, runs, scratches or mars Foreign matter imbedded Touch up, when applicable, not uniformly accanpli

45、shed Design Canponent parts do not assemble together or fit snugly Construction and Any hole missing workmanship Wssments missing or not located Bracket and disk holes not in Pins not securely riveted Rivet heads not countersunk as shown Characters not gothic type ietter “C“ not applied as specified

46、 Numerals not applied on both surfaces of numeral plates Numeral plates not numbered as specif ied Not required nunber of numeral plates characters not centered Sharp edges, burrs or slivers not Edges anci comers not rounded Edge of letter or numerals not as shown on drawing alignment remoVeed clear

47、ly defined Identification Missing, incanplete, not legible niarking 101 201 202 102 203 204 205 103 104 105 106 107 206 108 207 109 110 111 208 112 209 2 10 211 4.4.4 End itm dimensional examination. The end it- shall be examined for conformance to the dhensions specified on Drawing 6-1-2248 and as

48、specified herein. only those dimensions that can be evaluated without damaging or disassembling the end items shall be examined. Any dimension not 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-40b2bD = 999990b 19849LB 890 MIL-S-40626D(GL) w

49、ithin the specified tolerance shall be classified as a defect. shall be expressed in units of sign kits. kit. cause for rejection of the lot. The lot size The sample unit shall be one sign The finding of any defect shall be The inspection level shall be S-4. 4.4.5 End item testinq. The end items shall be tested for the vibration characteristic listed in 4.5.1. sign kits. shall be S-3. The lot size shall be expressed in units of The