ARMY MIL-S-52339 E (3)-1989 SHOP EQUIPMENT WOODWORKING TRAILER-MOUNTED《装在拖车上的木工制造工厂设备》.pdf

1、MIL-S-52339E (3) 32 I 9997905 025l11191 O MIL-S-52339E (ME) -3 9 March 1989 SUPERCEDING . AME“T2 18 March 1987 MImY SPECIFICATION This amemhent fom a part of MIGS-52339E(ME) , dated 23 August 1984, and is approved for use within the USA Belvoir Research, Developmt, and Engineering Center, Department

2、- of the Army and is available for use by all Departments and Agencies of the Department of Defense. PAGE 2 2.1, under SPECIFICATIONS, MILLTARY, ADD: “MIGC-46168 MIM-53 039 - Coating Aliphatic Polyurethane, Chemical Agent - Coating, Aliphatic Polyurethane, Single Component, Resistant. Chemical Agent

3、 Resistant.11 PAGE: 5 3.10, delete aric substitute the follming: “3.10 Treatment and paint-. The portiok of the shop normally painted internally and. externally shall be cleaned, treated, and painted in accordance With MIN-704, type F or G, as applicable. 6.2), top coat color shall be camouflage gre

4、en 383 conformhg to MIM-46168 or MILK-53039 as applicable. the Government furnished camouflage patt- with MILK-46168 top coat of the colors specified in the camouflage patterns, except the first article my be camouflage green 383.“ Unless otherwise specified (see The shop shall then be overcoated in

5、 accordance with PAGE 6 * 3.13, delete and substitute the following: l3.13 Noise Limits. The noise produced by the Shop Equipment shall conform with MIGSTD-1474 requirenents, with the exception of MTGSTD-1474 paragraphs 5.2, 5.3, and 5.4, when tested in accordance with 4.5.2.6. MIGSTD-1474, paragrap

6、hs 4.3 and 4.4 shall be provided if and only if MILrSTD-1474, paragraph 5.1.1.2 procelres have been pursued and documented to the satisfaction of the procuring activity and written permission to exceed the 85 distribution is unlimited. 1 of 3 Provided by IHSNot for ResaleNo reproduction or networkin

7、g permitted without license from IHS-,-,-MIGS-52339E (Mo) -3 3.14, add the following: “xm4 l?)-482 shall constitute failure of this test. PAGE 10 * 4.5.2.6, delete and substitute the following: Noise levels shall be measured in accordame with MIGSTD-2474 reqyiranents and reported in the formt hdicat

8、ed by MIL-STD-1474, Figure 7. noise levels chail be meacured when the generator is running and the raial saw is cutting a nominal 2 x 4 inch pine b0ai.d. MIbSTI3-1474, pagraph 5.12.1.4 contours shall be taken at not fewer than 12 equal (horizontal) arc incrmts, one incrmt shall include data from the

9、 noisiest position. position shall be provided as &(A) level. provisions shall constitute failure of this test.“ * 4.5.2.6.1, delete 3n its entirety. f14.5.2.6 Noise Level Test. a minimum: Additionally, the noise level at the typical operating Failure to comply with MIL-1474 * 4.5.2.6.2, delete in i

10、ts entirety. PAGE 14 6.2, add the following: lli. Color required when other than as specified (see 3.10) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. - MIL-S-52337E (3) 32 I 7777706 025LLi73 4 MIL-S-52339E (ME) AMENDMENT3 6.2.1 Acquisition req

11、uirements. Acquisition daxm-ents should specify the following: Upon final delivery of the first article it must be camouflage pattern painted. II The margins of the anm-dmnt are marked with an asterisk to indicate where changes (additions, modifications, corrections, deletion) from the previous amen

12、chrient were made. assumec no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the reqghments of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendxmt. This was done as a cornenience only and the Government l , custodian: Amry-m 3 - . . . . i_ - Preprkg activity: FYojeCt 3220-Al58 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-