ARMY MIL-STD-1488 G-1990 PROVISIONS FOR EVALUATING QUALITY OF TROUSERS《裤子质量评价条款》.pdf

1、flIL-STD-LLl88G 84 II 7777733 0088377 8 W MIL-STD-1488G 30 March 1990 SUPERSEDING MIL-STD-1488F 31 July 1987 MILITARY STANDARD PROVISIONS FOR EVALUATING QUALITY OF TROUSERS - -_ -_ AMSC N/A FSC 8405 DISTRIBUTION STATEYSNT A. Approved for piiblc release; distribution is unlimited. Provided by IHSNot

2、for ResaleNo reproduction or networking permitted without license from IHS-,-,-_II. _I_. I_ - MIL-STD-348G 4 7777733 0088378 T MIL-STD-1488G FOREWARD 1. This military standard is approved for use by all Departments and Agencies of the Department of Defense. 2. Beneficial comments (recommendations, a

3、dditions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of t

4、his document or by letter. 3, This standard provides a standardized procedure for evaluating quality of dress (D), semi-dress (SD) and utility (U) trousers procured for the Department of Defense. The objectives of this standard are to: a. Provide standard descriptions for trouser defects. b. Standar

5、dize examination requirements. 4. As of the date of approval of this document, the following specifications will reference this standard: DOCUMENT CLASSIFICATION TITLE MIL-T-1870 MIL-T-2423 MIL-V-17658 MI L- T- 2 1 7 0 4 MIL-T-21705 MIL-T-28902 MIL-T-28919 MIL-T-28920 MIL-T-29369 MIL-T-29452 MIL-T-4

6、1828 MIL-T-41834 MI L- T- 4 3 49 7 MIL-T-43654 MIL-T-43853 MIL-T-43932 MIL-T-43957 MIL-T-44047 MIL-T-44094 MIL-T-44372 U D D U U D D D D D D SD U U* D U D .U U U Trousers, Cold Weather; Field, Wool, M-1951 Trousers, Mens (White) Uniform, Mans (Dress white) Trousers, Cold Weather, Permeable Trousers,

7、 Extreme Cold Weather, Impermeable Trousers, Mens: Musicians Trousers, Mens: Service, Summer and Trousers, Mens: Dress (Officers) Trousers, Mens: Wool and Polyester/Wool Trousers, Mans: Polyester/Wool Trousers, Mens, Wool and Polyester/Wool Trousers, Mens, Polyester and Cotton Trousers, Cold Weather

8、, Field, Nylon and Trousers, Snow Camouflage, White, Arctic Trousers, Mens, Army Tan 445, Durable Trousers, Utility, (Durable Press) Trousers, Mens, Dress, Wool and Polyester/ Trousers, Camouflage Pattern; Combat Trousers, Night Camouflage, Desert Trousers, Aircrew, Camouflage Pattern; Winter (Offic

9、ers) Cot ton Press . woo 1 Combat ii Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DOCUMENT MIL-T-82161 MIL-T-82163 MIL-T-82199 MIL-T-87038 MIL-T-87039 MIL-T-87047 MIL-T-87062 MIL-T-87067 CLASSIFICATION D D-SD MIL-STD-1488G TITLE Trousers, Mens: Ev

10、ening Dress (Officers) Trousers, Mens: Dress, White; and Special Trousers, Mens: Mess, Black (Officers) Trousers, Mens (Blue, Enlisted) Trousers, Mens (Undress) Trousers , Mens Polyester/Wool Serge (CG) Trousers, Utility, Mens, Denim Trousers , Mens (Enlisted, White) Mess, Black iii Provided by IHSN

11、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-PARAGRAPH 1 1.1 1.2 2. 2.1 2.1.1 2.2. 2.3 3. 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 4. 5. 5.1 5.2 5.3 6. 6.1 6.2 6.3 6.4 6.4.1 6.4.2 6.4.3 6.4.4 7. MIL-STD-1488G CONTENTS SCOPE Pur pos e Application REFERENCE DOCUMENTS Govern

12、ment documents Specifications, standards, and handbooks Non-Government publications Order of precedence DEFINITIONS Fabric defects Knots and slubs Quality assurance terms and procedures Open seam Raw edge . Defective button Outside - inside Puckering GENERAL SAMPLE AND INSPECTION PROVISIONS End item

13、 examination Dimensional examination Packaging examination INSPECTION Inspection procedures initiation of inspection Continuation of inspection Switching procedures Normal to tightened Tightened to normal Normal to reduced Reduced to normal NOTES PAGE - 3 3 3 3 4 o 6 iv Provided by IHSNot for Resale

14、No reproduction or networking permitted without license from IHS-,-,-MIL-STD-1488G CONTENTS PAGE - TABLES I Sampling provisions for visual examination of dress (D) trousers 6 II Sampling provisions for visual examination of semi-dress (SD) trousers 7 IV Trousers visual defects 9 V Selected defects f

15、or visual examination of dress (D) trousers 27 III Sampling provisions for visual examination of utility (U) trousers a ILLUSTRATIONS I Zone defects for trousers 28 V Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-L48BG 84 m 99799LL 0088382

16、L m MIL-STD-1488G 1. SCOPE 1.1 Purpose. The purpose of this standard is to provide standardized provisions for evaluating the quality of dress, semi-dress, and utility trousers. 1.2 Application. This standard will be made applicable to contracts by reference in the appropriate trouser documents. The

17、 dress trouser documents require: (a) as a final step in the contractors production control plan before formulation of a lot, each of the dress trousers shall be examined after pressing and prior to folding for packaging and (b) any of the trousers containing a selected defect shall not be included

18、in the end item lot. Selected defects are those defects listed in table IV which are identified by an asterisk (“1 in the “Point value“ column. The selected defects are listed individually in table V. 2. REFERENCE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. Th

19、e following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto

20、, cited in the solicitation (see 7.1). STANDARDS FEDERAL FED-STD-4 - Glossary of Fabric Imperfections FED-STD-751 - Stitches, Seams, And Stitchings MIL I TARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by MIL-STD-109 - Quality Assurance Terms and Definitions MIL-STD-1491 - Glossary

21、of Knitting Imperfections Attributes (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The foll

22、owing document forms a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODI

23、SS are the issues of the documents cited in the solicitation. (see 7.1) 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1488G AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC) AATCC 88B (Two Photos) - Photographic Comparative R

24、ating of Single and Double Needle Seams (Applications for copies of Method 88B should be addressed to the American Association of Textile Chemists and Colorists, P.O. Box 12215, Research Triangle Park, NC 22709-2215,) (Non-Government standards and other publications are normally available from the o

25、rganizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence, In the event of a conflict between the text of this document and the references cited herein, the text of this document take

26、s precedence, Nothing in this docment, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3, DEFINITIONS 3.1 Fabric defects. Definitions of fabric defects, where applicable, shall be in accordance with FED-STD-4 and MIL-STD-1491. Fabric defects shall b

27、e clearly visible when examined at a distance of 3 feet. 3.2 Knots and slubs. Only knots and slubs that exceed the limits specified in the basic cloth document. and are clearly visible when examined at a distance of 3 feet shall be scored as defects in evaluating quality of the trousers. 3.3 Quality

28、 assurance terms and procedures. Definitions of quality assurance terms and procedures, where applicable, shall be in accordance with MIL-STD-105 and MIL-STD-109. 3.4 Open seam. Definitions of stitches, seams, and stitchings shall be in accordance with FED-STD-751. A seam shall be classified as open

29、 when one or more stitches joining the seam are broken or runoff, or when two or more continuous skipped stitches occur. Double stitched seams are considered open when one or both rows of the stitching are open. 3.5 Raw edge, Raw edge is defined as any edge not finished as specified including any pr

30、otruding raw edge on the outside of the trouser. 3.6 Defective button, A button shall be considered defective when it has sharp, rough, cracked, or split edge; has scratch, dent, blemish, or imbedded foreign matter; or is badly shaded. 3.7 Outside - inside. The terms “outside“ and “inside“ as used i

31、n this standard are defined as follows: Outside: Any part of the trousers that is visible when the completely buttoned and closed trousers are examined. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1488G Inside: Any part of the trousers

32、that is not visible when the completely buttoned and closed trousers are examined. 3.8 Puckering. In the course of the sampling examination, seams and stitch- ings suspected of being puckered shall be examined at a distance of 3 feet in comparison with the AATCC photographic comparative rating (see

33、2.2) for seams. Puckering on a major portion of the suspected seam that equals or is worse than rating 3 for single or multiple needle seams shall be scored as a puckered seam. 4. GENERAL 4.1 This standard contains the provisions for end item examination, dimensional examination, and packaging inspe

34、ction for dress, semi-dress, and utility trousers. If there are any inconsistencies between the requirement of the appropriate trouser document and the provisions of this standard, the trouser document shall control. This standard assigns to the listed defects, point values of 1, 2, or 3 depending o

35、n severity. The higher point values are assigned to those defects having the more detrimental effect on the appearance or serviceability of the item. The defects identified by an asterisk in the “Point value“ column of table IV are those defects having the most detrimental effect on the appearance o

36、r serviceability of the item. 5. SAMPLE AND INSPECTION PROVISIONS 5.1 End item examination. The inside and outside of the trousers shall be examined and all defects shall be penalized as indicated in table IV. ID“ signif ies dress trousers. “SD“ signifies semi-dress trousers. “U“ signif ies utility

37、trousers. The sample size shall be based on lot size, and the acceptable point values for selected defects, 3 and 2 point defects, and total (3, 2 and 1 point) defects shall be as specified in table I, II, or III as applicable. The sample unit shall be one of the finished trousers. The lot shall be

38、unacceptable if: a. The point value or 3 and 2 point defects exceeds the applicable maximum acceptable point value or b. The point value for total (3, 2, and 1 point) defects exceeds the applicable maximum acceptable point vaiue or c. The number of selected defects (see .1.2) exceeds- the maximum al

39、lowed for the sample size (see table I). 5.2 Dimensional examination. The appropriate number of trousers, determined from the table below, shall be examined for conformance to the dimensional requirements cited in the table of measurements of the appropriate trouser docu- ment. When a measurement de

40、viates from a dimension and tolerance specified, the 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1488G trousers shall be penalized one point. Each sample unit shall also be penalized one point when the inseams are uneven in length by 1/

41、2 inch or more. The lot shall be unacceptable if the total point value resulting from this examination exceeds the maximum acceptable point value, Each size of the trousers present . in the lot should be represented in the sample selected for this examination. Sampling provisions for dimensional exa

42、mination Lot size Up thru 500 501 thru 3,200 3,201 thu 35,000 35,001 and up Sample size Maximum acceptable point values 8 13 20 32 5.3 preser of the Packaging examination, An examination shall be made to determine that vation, packing, and marking requirements are in compliance with section 5 approp

43、riate trouser document. Defects listed below shall be scored one point. The sample size for this examination shall be five shipping containers fully packaged with the exception that they need not be closed. Defects of closure listed below shall be examined on shipping containers fully prepared for d

44、elivery, The lot shall be unacceptable if one or more points are scored for this examination. Examine Defect Marking (exterior Omitted; incorrect; illegible; of improper size, and interior) location, sequence, or method of application. Materials Inadequate application of components, such as: incompl

45、ete closure of container flaps, loose strapping, improper taping, improper adhesive application, or inadequate stapling. Open and ncn-continuous heat sealed seams and closure of polyethylene bag. i/ Alternative closure of-polyethylene bag not provided with tuck or reverse flap. L/ Omission of vent h

46、ole in polyethylene bag. L/ Incorrectly fabricated bag. I/ Bulged or distorted container. Content Number of bundles or intermediate packages per Number of trousers per bundle or intermediate Packaged insde out. Size shown on one or more trousers not as specified container is more or less than requir

47、ed. package is more or less than required. 2/ on outside of shipping container. - 2/ Preservative application Improperly applied or missing. L/ (napthalene flakes) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-LYBBG 84 7777733 00B838b 7 M

48、IL-STD-1488G - i/ When applicable. - 21 For this defect, one bundle or intermediate package from each container in the sample shall be examined. 6. INSPECTION 6.1 Inspection procedures. Inspection procedures, except for sampling plans, shall be as specified in MIL-STD-105, except where otherwise ind

49、icated in this document. 6.2 Initiation of inspection. Normal inspection shall be used at the start of inspection unless otherwise directed by the responsible procurement quality assurance element administering the contract. 6.3 Continuation of inspection. Normal, tightened, or reduced inspection shall continue unchanged on successive lots except where switching proce