ARMY MIL-STD-655 D-1992 PROVISIONS FOR EVALUATING QUALITY OF CLOTH WOOL WORSTED AND WOOL BLENDS《绒线和毛混纺布质量评价条款》.pdf

1、NIL-STD-655D 83 m 9999911 0305382 90T m .I I MIL-SID- 6 55D 6 Ausust 1992 SUPERSEDING MIL-STD-655C 19 September 1985 MILITARY STANDARD PRVISIoNS FOR EV-TING QUALITY OF CUYIH, WOOL, mm AND WOOL BLENDS AMSC N/A FSC 8305 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.

2、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-655D 83 D 9999933 0305383 84b D MIL-SID-655D 1. Agencies of the Department of Defense. This Military Standar is approved for use by all Departments and 2. pertinent data which may be used in imp

3、roving this document should be addressed to: Center, Natick, MA 01760-5019, by using the Standardi zation Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. Beneficial cmnts (recormiendations, additions, deletions) ami any U.S. Army Natick Research, Deve

4、lopnent, and Engineering 2.1 Government documents. 2.1.1 Specifications, standards, and hanbookS. The following specifica- tions, standards, and handbooks form a part of this document to the extent specified herein. are those listed in the issue of the Department of Defense Index of Specifications a

5、nd Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.1). Unless otherwise specified, the issues of these documents STANDARE FEDERAL FED-STD-191 - Textile Test Methock MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection MIL-STP-109 - Quality Assurance Tenirj

6、 and Definitions by Attributes (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Standardi zation Documents Order Desk, Wlilding 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.1.2 other Government documents, drawinus,

7、 and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. the issues are those cited in the solicitation. Unless otherwise specified, FEDERAL TRADE CcblMISSION Rules and Regulations Under the Wool Products Iab

8、eling Act (Copies are available from the Federal Trade Comnission, Pennsylvania Avenue at Sixth Street, N.W., Washington, DC 20580-0001.) ii Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-SID- 655D 2.2 Order of precedence. In the event of a conf

9、lict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exerqtion has been obtained. 3. woolen, worsted, and wool blended cloths procured for th

10、e Department of Defense. This standard provides a standardized procedure for evaluating quality of 4. tions will reference this standard: As of the date of approval of this standard, the following specifica- SPECIFICATION TITLE MIL-C-82 3 MIL-C-3727 MIL-C-3738 MIL-C-10176 MIL-C-11065 MIL-C-16290 MIL

11、-C-16291 MIL-C-17566 MIL-C-2 11 15 MIL-C-24903 MIL-C-24910 MIL-C-29405 MIL-C-82252 Cloth, Serge, Wool; Wool and Nylon, Polyester Cloth, Wathea, Wool Cloth, Elastique, Wool Cloth, Gabardine: Wool, Polyester and Wool Cloth, Flannel, Wool and Nylon, l-unce, Shrink Cloth, Melton, Wool (Moth-Proofed) (SA

12、) Cloth, Flannel, Wool (SA) Cloth, Billiard cloth, Tropical: Wool, Polyester/Wool Cloth, Elastique, Polyester/Wool (CG) Cloth, Tropical: Polyester and Wool Cloth, Broadcloth: Wool and Wool/Nylon (PE) Cloth, Broadcloth, Wool and Wool-Synthetic and Wool Resistant (CL) (MothProofed) (Nu) iii Provided b

13、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-655D 83 99999LL 0305385 bL9 PARAGRAPH 1. 1.1 1.2 2. 2.1 2.2 3. 3.1 3.2 3.3 4. 5. 5.1 5.1.1 5.1.2 5.1.3 5.1.3.1 5.1.3.2 5.1.4 5.1.5 5.1.6 5.2 6. 6.1 6.2 6.3 TABLE I MIL-SID-655D REFERENCED- Government docu

14、ments order of precedence DEFINITIONS Fabric defects Fabric defect (not scorable) Quality assurance tenir; 1 1 1 1 1 1 DETAILED REQUIREMENTS End item examination Yard-by-yard examination Shade variation examination Length examination Individual roll Total yardage in the sample Roll examination Shade

15、 match and appearance examination Defect marking (stringing of defects) Inspection procedures examinat ion NOIES Applicable documents Subject term (key word) Listing Changes fran previous issue 6 6 Maximum acceptable point values 5 iv . e e e Provided by IHSNot for ResaleNo reproduction or networkin

16、g permitted without license from IHS-,-,-MIL-STD-b55D 83 9999911 O305386 555 MIL-STD-655D 1. SCOPE 1.1 mirpose. The purpose of this standard is to provide standardized examination provisions for evaluating quality of woolen, worsted, and wool blended cloths that are the basic materials for quality u

17、niform items. 1.2 Scope. This standard will be made applicable to contracts by reference in the appropriate cloth documents. 2.1 Govenunent documents. Unless otherwise specified, the following documents of the issue in effect on date of invitations for bids or request for proposal, form a part of th

18、is document to the STANARDS FEDERAL4 FED-STD-191 - Textile Test Methods MILITARY MIL-STD-105 - Sampling Procedures and by Attributes MIL-STD-109 - Quality Assurance Terms (Copies of documents required by contractors in acquisition functions should be obtained from the directed by the contracting act

19、ivity.) mR GOVERNMENT - Laws and Requlations Rules and Regulations Under the Wool Products extent specif ied herein. Tables for Inspection and Definitions connection with specific contracting activity or as Labeling Act (Application for copies should be addressed to the Superintendent of Docu- ments

20、, U.S. Govemnt Printing Office, Washington, DC 20402.) 2.2 Order of precedence. In the event of a conflict between the text of this standard and the references cited herein, the text of this standard shall take precedence. 3. DEFINITIONS 3.1 Fabric defects. standard are described The fabric defect d

21、efinitions applicable to the as follas: 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-655D 83 99999LL 0305387 491 MIL-STD-655D 3.1.1 Barre. Bands, streaks, or bars in the fabric characterized by texture, tension, color, luster, or shrinka

22、ge differences. 3.1.2 Bawed or skewed filling. Cloth in which the filling yarn does not run at right angles to the warp. 3.1.3 Broken or missins yarn. A yarn partially or entirely missing. 3.1.4 Coarse or heaw yarn. A yam larger in diameter than normally being used in the cloth. 3.1.5 Defective selv

23、aqe. Selvage that is curled, folded, rolled, slack, tight, scalloped, wavy, stringy, beaded, loopy, cut, tom, missing, or raveled, or not adequately anchored to the edge of the cloth, preventing the unraveling of the edge. 3.1.6 Excess material. Extra yarn or waste which has been woven into the clot

24、h or spun into the yarn, or extra length of yam that has not cqletely been woven into the cloth. 3.1.7 Fine yarn. A yarn smaller in diameter than normally being used in the cloth. 3.1.8 Finishinq imperfections. Cloth which has not been uniformly sheared, does not have the same degree and character o

25、f finish throughout, has tentering marks, or is streaked, blotched, spotted, or otherwise =ked. 3.1.9 Heaw or liqht place. A fillingwise band or bar either across the full width of the cloth or a portion of it containing more or less than the normal number of picks, or containing picks of larger or

26、smaller diameter than normally being used in the cloth. 3.1.10 me. A place in the cloth where two or more contiguous yams have been ruptured. 3.1.11 Knot. Self descriptive. To be scored when it exceeds the limits specified in the basic cloth document. 3.1.12 Misweave. Any deviation fran the specifie

27、d weave pattern. 3.1.13 Mixed yarn. Yarn which differs fran that normally being used in the cloth, such as wrong twist, wrong number of plies, wrong color, or mixed yarn lots. 3.1.14 Neppiness. A speckled condition of the cloth characterized by a number of definite fiber tangles (neps). 3.1.15 Ope n

28、 place. An open streak or crack which results in a clearly noticeable separation between the yarns. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-b55D 83 m 9999911 0305388 328 m MIL-STD-655D 3.1.16 Reed mark. A mark or line running warpis

29、e in the cloth. 3.1.17 m. A thick place in the yarn. To be scored when it exceeds the limits specified in the basic cloth document. 3.1.18 Spot, stain or streak. An area in the cloth or on the surface of the cloth showing discoloration, foreign matter, or soil, excluding decating marks. 3.1.19 Uneve

30、n yarn. A yarn tighter or slacker than the normal yarn in the boy of the cloth. 3.1.20 Wavy cloth. Cloth that is of such a nature (baggy, ridgy, wavy, or contains crease) that it will not lie flat on a cutting table. 3.1.21 Weak spot. A place in the cloth where the surface has been damaged or has be

31、en abnormally weakened. 3.1.22 Uneven weavinq. Irregular cloth characterized by conditions such as short elliptical or triangular distortions of one or more adjoining yams, tight or slack places in the same yam, crimped, rippled, wavy, pebbled, or cockled place in the cloth. 3.2 Fabric defect (not s

32、corable). 3.2.1 Decatins mark. A seam or fabric-end impression extending filling-wise across the cloth. 3.3 Quality assurance tem. Definitions of quality assurance terms shall be in accordance with MIL-SID-105 and MIL-SID-109. 4.1 This standard contains provisions for visual examination of woolen, F

33、abric quality in the following quality worsted and wool blended cloths. levels shall be as specified in the applicable cloth docrurident. Quality Level 8 Quality &vel 10 Quality -vel 12 Quality &vel 15 5. DETAILED REQUIREMENIS 5.1 End item examination. 5.1.1 Yard-by-yar examination. The total yardag

34、e of each roll in the sample shall be examined on the face side. Ail appropriate defects that are 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-b55D 83 m 7799933 0305389 269 m MIL-STD-655D clearly noticeable at normal inspection distance

35、(3 feet) shall be scored and assigned demerit points as specified in this paragraph. shall be in accordance with the following: The sample size Lot size (yards1 -le size (rolls 1/ 500 or less 501 up to 3,200 3,201 to 35,000 35,001 and over a 13 20 32 Point value computation shall be as follows: Tota

36、l points scored in sample X 3600 = Points per Contracted width of cloth (inches) X Total yards inspected 100 square yards The following defect, when present, shall be scored four points for each yard in which it occurs. Width less than specified. Except for above defect, all defects as defined in se

37、ction 3.1 of this standard shall be scored and assigned demerit points as follows: - one point For defects 3 inches or less in any dimension For defects exceeding 3 inches, but not exceeding 6 inches in any dimension - tm points For defects exceeding 6 inches, but not exceeding 9 inches in any dimen

38、sion - three points - four points For defects exceeding 9 inches in any dimension The same yardage shall be given a through - lighting inspection on the face side of the cloth for holes and thin areas not previously scored. open places resulting from removal of burrs, shives, sisal or broken picks n

39、ot previously scored shall not be scored in through - lighting inspection. Slight - i/ No more than one roll shall be taken from any shipping container unless the number of shipping containers in the lot is less than the required number of rolls in which case all shipping containers shall be present

40、 in the sample. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-tlIL-STD-bS5D 83 9999933 0305390 T8b MIL-sm-6 55D Selvage defects shall be scored when the thickness of the selvage exceeds the thickness of the body of the cloth by an excessive amoun

41、t 2/ or the edge of the cloth is not adequately anchored. No linear yard (increments of 1 yard on the measuring device of the inspection machine) shall be scored more than four points, however, all defects shall be recorded. The lot shall be unacceptable if: a. The point value per 100 square yardc f

42、or the total yardage in the entire sample exceeds the applicable maximum acceptable point value (see table I). b. The point value per 100 square yards for the total yardage in any individual roll in the sample exceeds the applicable maximum acceptable point value (see table I). TAEXE I. Maximum acce

43、ptable point values Maximum acceptable point values Quality Level Entire sample Individual rolls 8 8 points per 100 sq. yd. 12 points per 100 sq. yd. No?TMl 10 10 points per 100 sq. yd. 15 points per 100 sq. yd. Inspection 12 12 points per 100 sq. yd. 18 points per 100 sq. yd. 23 points per 100 sq.

44、ud. 15 15 points per 100 sq. yd. 5.1.2 Shade variation examination. During the yard-by yard examination, each roll in the sample shall be examined for shade variation. Any roll in the sample containing uneven shade or shade variation side to side, side to center, or end to end, shall be cause for re

45、jection of the entire lot represented by the sample. 5.1.3 LenW examination. During the yard-by-yard examination, each roll in the sample shall be examined for length. 5.1.3.1 Individual roll. Any length found to be less than the minimum length specified in the basic cloth document or more than 2 ya

46、rds less than the length marked on the ticket shall be scored as a defect. The lot shall be unacceptable if two or more rolls in the sample are defective in respect to length. - 2/ In the case of dispute, the thickness of the selvage shall not exceed the thickness of the body of the cloth by more th

47、an 40 percent, when tested in accordance with Method 5030 of FED-STD-191. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL- SID- 6 55D 5.1.3.2 Total vardaae in sarmle. The lot shall be unacceptable if the total of the actual length of the rolls

48、in the sqle is less than the total of the lengths marked on the roll tickets. 5.1.4 Roll examination. During the yard-by-yard examination each roll in the sample shall be examined for defects listed below. unacceptable if two or more of the following defects are present in the sample : The lot shall

49、 be Back stamping missing, incorrect or illegible from either or both ends, or bleed through occurring. Back stamping on wrong side. Letters less than 1/2 inch in height. Not labeled or ticketed in accordance with the Rules and Regulations Edge of roll build-up, or softness of roll in body of cloth. under the Wool Products Labeling Act. 5.1.5 Shade match and appear ance examination. The shade mat