ARMY MIL-STD-902 A-1988 PROVISIONS FOR EVALUATING QUALITY OF CAPS GARRISON WOMEN'S《女式船形军帽质量评价条款》.pdf

1、c- MIL-STD-702A L( m 7777711 0081027 1 C-g4- (D MIL-STD-902A 12 June 1988 SUPERSEDING MIL-STD-902 20 May 1974 MILITARY STANDARD PROVISIONS FOR EVALUATING QUALITY OF CAPS, GARRISON, WOMENS AMSC N/A FSC 8410 DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited. THIS DOCUMEN

2、T CONTAINS I 7 PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- -_F _I _I -_ -_- MIL-STD-702A.84 m 7777731 0083028 3 m MIL-STD-902A FOREWORD * 1. This military standard is approved for use by all Departments and Agencies of the Department of D

3、efense. * 2. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014 by using the self-addressed Standardization Doc

4、ument Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. * 3. This document supplements the military specifications listed below. It provides a standard description -for defects and standardizes examination requirements. TITLE - SPECIFICATION MIL-C-15507 - Cap, G

5、arrison, Womans (Navy) MIL-C-40094 - Cap, Garrison, Womans, Summer MIL-C-43447 - Caps, Garrison, Womens Wool and Polyester/Wool * MIL-C-87014 - Cap, Garrison, Womans (Coast Guard) * MIL-C-87215 - Cap, Garrison, Womans, Air Force ii Provided by IHSNot for ResaleNo reproduction or networking permitted

6、 without license from IHS-,-,-Paragraph 1. 1.1 1.2 2. 2.1 2.1.1 2.2 2.3 2.4 2.4.1 2.4.2 3. 3.1 3.2 3.3 3.4 3.5 3.6 3.7 4 5. 5.1 5.2 5.3 5.4 5.5 5.5.1 5.5.2 5.5.3 5.5.4 5.6 5.7 5.8 6. 6.1 6.2 6.3 Table I. II. III. MIL-STD-902A. 84 = 9999931 0083029 5 E MIL-STB-902A CONTENTS SCOPE Scope Purpose APPLIC

7、ABLE DOCUMENTS Government documents Standards Non-Government publications Order of precedence Source of documents Government standards Non-Government publications DEFINITIONS Fabric defects Knots and slubs Open seam Raw edge Outside-inside Puckering Quality assurance terms and procedures GENERAL REQ

8、UIREMENTS DETAILED REQUIREMENTS Purpose Inspection procedures initiation of inspection Continuation of inspection. Switching procedures Normal to tightened Tightened to normal Normal to reduced Reduced to normal End item visual examination End item dimensional examination Packaging examination INFOR

9、MATION FOR GUIDANCE ONLY Intended use Subject term (key word) listing Changes from previous issue Page 1 1 1 2 2 2 2 3 3 3 3 3 4 4 4 4 4 4 5 14 14 15 15 15 15 TABLES Sampling provisions for end item visual examination 5 Sampling provisions for end item dimensional End item visual defect point values

10、 7 examination 14 iii o Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-702A 4 W 79777LL 0081030 L MIL-STD-902A 1. SCOPE * 1.1 Scope. This document covers standardized provisions for evaluating the quality of garrison caps for women. * 1.2 Pu

11、rpose. This standard is applicable to government procurements cited in the specifications listed below: MIL-C-15507 - Cap, Garrison, Womans (Navy) MIL-C-17767 - Cap, Garrison, Womans; Polyester Fiber-cotton, Green and MIL-C-40094 - Cap, Garrison, Womans, Summer MIL-C-43447 - Cap, Garrison, Womans Wo

12、ol and Polyester/Wool MIL-C-87014 - Cap, Garrison, Womans (Coast Guard) White * 2. APPLICABLE DOCUMENTS * 2.1 Government documents. * 2.1.1 Standards. The following standards form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are th

13、ose listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation. STANDARDS FEDERAL FED-STD-4 - Glossary of Fabric Imperfections FED-STD-751 - Stitches, Seams and Stitching MILITARY MIL-STD-105 - Sampling Procedures

14、 and Tables for Inspection by MIL-STD-109 - Quality Assurance Terms and Definitions Attributes HANDBOOKS MIL-HDBK-156 - Military Standardization Handbook - Glossary of Military Fabrication Terms 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL

15、-STD-902A * 2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DODISS specified in the solicitation. Unless otherwis

16、e specified, the issues of documents not listed in the DODISS are the issues of the non- Government documents which are current on the date of the solicitation. AATCC Photographic Comparative Rating of Single and Double Needle Seams (Method 88B, two photos) * 2.3 Order of precedence. In the event of

17、 a conflict between the text of this document and the references cited herein, the text of this document shall take precedence. Nothing in this document, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. * 2.4 Source of documents. * 2.4.1 Governm

18、ent standards. Copies of the referenced federal and military standards are available from the Department of Defense Single Stock Point, Commanding Officer, Naval Publications and Forms Center, 5801 Tabor Avenue, Philadelphia, PA 19120-5099. For specific acquisition functions, these documents should

19、be obtained from the contracting activity or as directed by the contracting activity. * 2.4.2 Non-Government publications. Non-Government documents are generally available for reference from libraries and technical groups, The documents listed may be obtained as follows: AATCC Photographic Comparati

20、ve Rating of Single and Double Needle Seams (Method 88B, two photos) : (Copies may be obtained from The American Association of Textile Chemists and Colorists, P.O. Box 12215, Research Triangle Park, NC 27709.) 3. DEFINITIONS * 3.1 Fabric defects. Definitions of fabric defects, where applicable, sha

21、ll be in accordance with FED-STD-4. * 3.2 Knots and slubs. Only knots and slubs that exceed the maximum limi-ts specified in the basic cloth specification shall be scored as defects in evaluating quality of the finished cap. * 3.3 Open seam. A seam shall be classified as open when one or more stitch

22、es joining a seam are broken or runoff, or when two or more continuous skipped stitches occur. Double stitched seams are considered open when one or both rows of stitching are open. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-702A 8Lt =

23、 777773L 0083032 5 = MIL-STD-9 Q2A * 3.4 Raw edge. A raw edge is defined as any edge not finished as specified including any protruding edge on the outside of the cap. 3.5 Outside-inside. The terms “outside“ and “inside“ as used in this standard are defined as follows: Outside - Any part of cap that

24、 is visible when the cap is examined from a distance of 3 feet at shoulder level height and positioied as worn. The cap shall be completely rotated. Inside - Any part of cap that is not visible when the cap is examined from a distance of 3 feet at shoulder level height and positioned as worn. The ca

25、p shall be completely rotated. * 3.6 Puckering. In the course of the sampling examination, seams suspected of being puckered shall be examined with the cap lying flat on the inspection table at a distance of 3 feet and shall be rated in comparison with the AATCC photographic comparative rating for s

26、eams. suspect seam that is less than rating 4 for single needle seams or double needle seams shall be scored as a puckered seam. Puckering on a major portion of the 3.7 Quality assurance terms and procedures. Definitions of quality assurance terms and procedures, where applicable, shall be in accord

27、ance with MIL-STD-105 and MIL-STD-109. .# 4. GENERAL REQUIREMENTS This section is not applicable to this standard. * 5. DETAILED REQUIREMENTS * 5.1 Purpose. This standard contains inspection provisions for-end item If there are any inconsistencies between the requirements of the examination, dimensi

28、onal examination and packaging examination for garrison caps. appropriate cap specification and the provisions of this standard, the cap specification shall control. This standard assi-gns to the listed defects, point values of 1, 2, or 3 depending on degree of severity. are assigned to those defect

29、s having more detrimental effect on the appearance or serviceability of the item. The higher point values 5.2 Inspection procedures, Inspection procedures shall be as specified in MIL-STD-105 except where otherwise indicated in this document. * 5.3 Initiation of inspection. Normal inspection shall b

30、e used at the start of inspection unless otherwise directed by the responsible procurement quality assurance element administering -the contract. 3 d Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-702A 4 W 77777311 OO3033 7 W MIL- STD- 90 2

31、A 5.4 Continuation of inspection. Normal, tightened or reduced inspection shall continue unchanged on successive lots except where switching procedures in 5.5 require a change. 5.5 Switching procedures. 5.5.1 Normal to tightened. When normal inspection is in effect, tightened inspection.-shall be in

32、stituted when two out of five consecutive lots have been rejected on original inspection (i.e., ignoring resubmitted lots for this procedure). 5.5.2 Tightened to normal. When tightened inspection is in effect, normal inspection shall be instituted when five consecutive lots have been considered acce

33、ptable on original inspection. 5.5.3 Normal to reduced. When normal inspection is in effect, reduced inspection shall be instituted providing that all of the following conditions are satisfied: l a. The preceding 10 lots have been on normal inspection and none have been rejected on original inspecti

34、on; and b. The total number of points for 3 and 2 point defects in the samples from the preceding 10 lots is equal to or less than 60 percent of the total maximum acceptable point values for 3 and 2 point defects from the preceding 10 lots; and c. The total number of points for 3, 2 and 1 point defe

35、cts in the sample from the preceding 10 lots is equal to or less than 75 percent of the total maximum acceptable point values for 3, 2 and 1 point defects from the preceding 10 lots; and * d. Production is at a steady rate; and * e. Reduced inspection is considered desirable by the procurement quali

36、ty assurance element administrating the contract. 5.5.4 Reduced to normal. When reduced inspection is in effect, normal inspection shall be instituted if any of the following occur on original inspection: a. A lot is rejected; or b. A lot is considered acceptable but exceeds the applicable first val

37、ue (see L/ to table I); or C. Production becomes irregular or delayed; or d, Other conditions warrant that normal inspection be instituted. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-7DZA 4 7777733 OO3034 7 I MIL-STD-902A .k 5.6 End it

38、em visual examination. The caps shall be examined as indicated in section 3 for all defects except puckering. The puckering examinaton shall be as described in 3.6. All defects shall be assigned point values as indicated in table II. The sample size shall be based on lot size, and the acceptance val

39、ues for 3 and 2 point defects and total (3, 2 and 1 point) defects shall be as specified in table I. The sample unit shall be one finlshed cap. The lot shall be unacceptable if: a. The point value for 3 and 2 point defects exceeds the applicable maximum acceptable point value; or b. The point value

40、for total (3, 2 and 1 point) defects exceeds the applicable maximum acceptable point value. TABLE I. Sampling provisions for end item visual examination Maximum acceptable point values Sample 3 incorrect; illegible; of improper . and interior) size, location, sequence, or method of application, Mat

41、er ia 1 s Any component missing, damaged, or not as specified. Workmanship Inadequate application of components, such as: improper taping, loose strapping or inadequate stapling. polyethylene bag. i/ tuck or reverse flap. L/ incomplete sealing or closure of flap, Open and noncontinuous heat sealed s

42、eams in closure of Alternative closgeof polyethlene bag not provided with Omission of vent hole in polyethylene bag. - 1/ Incorrectly fabricated bag. i/ Bulged or distorted container, Content Number of intermediate cofitainers is more or less than required. 14 Provided by IHSNot for ResaleNo reprodu

43、ction or networking permitted without license from IHS-,-,-MIL-STD-702A BL( M 9997733 OO304Li 3 I MIL-STD-902A , Examine Defect (cont d) Content (contd) Number of caps per intermediate container is more or less than required. shipping container. 2/ Size shown on one or more caps not as specified on

44、Preservation Improperly applied or missing. L/ (Napthalene flakes) - i/ When applicable. - 2/ For this defect, one intermediate package from each shipping container in the sample shall be examined. * 6. INFORMATION FOR GUIDANCE ONLY * (This section contains information of a general or explanatory na

45、ture which is helpful, but is not mandatory.) * 6.1 Intended use. This document is intended to provide a standard description for defects and examination requirements encountered by Departments and Agencies of the Defense Department in the procurement of caps, garrison, womens. * 6.2 Subject term (k

46、ey word) listing. Examination Inspec tion Caps, Garrison, Womens Uniforms * 6.3 Changes from previous issue. The margins of this document are marked with an asterisk (*) to indicate where changes (additions, modifications, corrections, deletions) from the previous issue were made. This was done as a

47、 convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content, irrespective of the marginal notations and relationship to the previous issue

48、. 15 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Custodians: Army - GL * Navy - Nu * Air Force - 11 Review activities: Navy - MC * Air Force - 82, 99 * DLA- CT Preparing activity: Army - GL Project No. 84104654 *US. GOVERNMENT PRINTING OmCE IW - 5BSMSI9ZSSZ 16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-