ARMY MIL-T-11196 F-1993 TOOL-KIT ELECTRICIANS' NUMBER ONE《1号电气工工具箱》.pdf

1、MIL-T-11196F 27 September 1993 SUPERSEDING MIL-T-11196E 30 September 1986 MILITARY SPECIFICATION TOOL-KIT, ELECTRICIANS : NUMBER Oh This specifications is approved for use by all Diprtments and Agencies of the Depclrtment of Defense. 1. SCOPE 1.1 Scope. This document covers the number one electricia

2、ns tool-kit (see 6.1). 2. APPLICABLE lmfxmws 2.1 Government docurrients. 2.1.1 Specifications, standards, and handbooks. The following specifica- Unless otherwise specified, the issues of these documents tions, standards, and handbooks form a part of this document to the extent specified herein. are

3、 those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS A-A-453 - Frame, Hand Hacksaw: Adjustable LRngth A-A-1307 - Harmer, Hand, Carpenters, Nail, Curved Claw A-A-1898 - Cushio

4、ning Material, Cellulosic, Packaging A-A-2312 - File, Hand (American Pattern), Half-Round A-A-2316 - File, Hand (American Pattern), Mill Beneficial cmnts (recmndations, additions, deletions) and any pertinent data which may be used in improving this document should be addressed to: Center, Natick, M

5、A 01760-5017, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. U.S. Army Natick Research, Developnt, and Engineering - AMCC N/A Fsc 5180 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. O Pr

6、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-LLLSbF m 9999906 195Lib2 bbT m * A-A- 2 3 1 8 A-A- 2 32 9 A- A- 2 3 30 A-A-2344 A-A-2 552 A-A- 2 5 5 5 A-A-51120 W-P-796 KK-B-151 NN-H-85 GGG-A-09 1 GGG-B-175 CCG-B- 3 8 3 GGG-B-451 GGG-B-671 GGG-C-

7、 3 1 1 GGG-C-313 GGG-c-771 GGG-C- 1520 GGG-K-27 5 CCG-K-484 GOG-L-2 11 GGG-P-47 1 GGG-P-836 GGG-R-791 GGG-S-65 GGG-T-106 GGG-T- 13 1 O GGG-W-651 PPP-P-40 PPP-P-291 PPP-T-60 MILITARY MIL-P- 116 MIL-G-2366 MIL-F-3747 MIL-M-9983 MIL-C-22520 MIL-T-11196F File, Hand (herican Pattern), Round, Regular Plie

8、rs, Diagonal Cutting Wrenches, Adjustable Drill, Push Drill, Masonry, Hand (Star (Four-Flute) Drill) Torch Kit, Soldering (Propane Gas) Fullers, Fuse Belt, Linemans; and Strap, Pole Linemans Type Handle, File (Adjustable Type) Awls Bender, Electrical Conduit, Hand (Portable) Bits, Wood-Boring; and C

9、hisels, Mortising, Hollow Blade, Hand Hacksaw and Blade, Power Hacksaw Brace, Bit, Ratchet; Brace, Bit, Comer; and Chisels and Gouges, Woodworking Chisels, Hand: Cape, Diamond Point, Cold, Round Cutters, Pipe; and Cutters, “ube Carrier Tool Key, Socket Head Screw Knife, Pocket, (Heavy Duty) Levels a

10、nd Plumbs, and Levels Pliers; Pliers, Slip Joint Punch and Die, Knockout Rules, Measuring Saws, Hand Tape, Measuring, (General Use) Tape, Fish, Steel Wrenches; Pipe Wrench and Basin Wrench Preservation and Packing of Hand Tools; Tools and Tbol Accessories for Power Driven, Metal and Woodworking Mach

11、inery Paperboard, Wrapping and Cushioning Tape: Packaging, Waterproof Rasp, Hand, wood Extensions, Bit Nose, and Side Cutting - Preservation, Methods Of - Gloves, Mens and Womens, Heavy Duty - Flashlights: Plastic Case, Tubular (Regular, Explosion-Proof, Explosion-Proof Heat-Resistant, Traffic-Direc

12、ting, and Inspection-Light) - Multimeters, Clamp-On - Crimping Tools, Terminal, Hand or Power Actuated, Wire Termination, and Tool Kits, General Specification For Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-LllbF = 0b L5L7b3 5Tb MIL-T-11196

13、F STANDARDS MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes MIL-STD-129 - Marking for Shipnt and Storage MIL-STD-147 - Palletized Unit Loads (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the

14、Standaniization Doc=uments Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The folluwing documents form a part of this document to the extent specified herein. the issues of the documents which are DOD adopted are those listed in the issue

15、of the DODISS cited in the solicitation. the issues of docurrients not listed in the DOLIISS are the issues of the documents cited in the solicitation (see 6.2). Unless otherwise specified, Unless otherwise specified, AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for C

16、omnercial Packaging (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) AMERICAN NATIONAL STANDAFDS INSTITUE (ANSI) O B107.13 - Pliers (mng Nose, ang Reach) B107.15 - Flat Tip and Phillips Screwdrivers B107.20

17、 - Pliers (Linemans, Iron Workers, Gas, Glass, and Fence) (Application for copies should be addressed to the American National Stan- Institute, Inc., 11 West 42nd Street, New York, NY 10036.) (Non-Government standards and other publications are normally available fran the organizations that prepare

18、or distribute the documents. documents also may be available in or through libraries or other infom- tional services.) These 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in t

19、his dcamnt, however, supersedes applicable laws and regulations unless a specific exaption has been obtained. 3. REQUI- 3.1 Materials. Materials not definitely specified shall conform to the mufacturers current comnercial practice. It is encouraged that recycled 3 Provided by IHSNot for ResaleNo rep

20、roduction or networking permitted without license from IHS-,-,-MIL-T-LLLSbF m 99999Ob 19517b4 432 m MIL-T-11196F material be used when practical as long as it meets the requirements of this specification. 3.2 Component details. The tool kit shall consist of a tool box and the tools listed in table I

21、 document and/or National Stock Number (NSN), or shall be standard catalog products, as applicable, except for such deviations fran manufacturers standards as may be required by the details in this document. “or equal“ is used, it shall be interpreted to mean that all established functional require

22、ments have been met. The listed tools shall conform to the referenced where the term TABLE I. Components Item Cmponent National Stock Number Quantity 1 Awl, scratch, conforming to type V 5120-00-221-1542 2 ea. of GG-A-891 2 Belt, linemans, conforming to KK-B-151 5140-00-529-2694 2 ea. 3 Bender, elec

23、trical conduit, hand, con- 1 ea. forming to type I, size 3/4 inch of GG-B-175 (heavy steel conduit) 4 Bender, electrical conduit, hand, con- forming to type II, size 1/2 inch of GGG-B-175 (electrical metallic tubing 5 Bender, electrical conduit, hand, con- forming to type II, size 3/4 inch of GG-B-1

24、75 (electrical metallic tubing 6 Bit, wood-boring, auger, conforming to type I, class A, size 1/4 inch of GG-B- 3 83 7 Bit, wood-boring, auger, confonning to type I, class A, size 3/8 inch of GGG-B-383 8 Bit, wood-boring, auger, conforming to type I, class A, size 1/2 inch of GG-B- 3 8 3 9 Bit, wood

25、boring, auger, conforming to type I, class A, size 5/8 inch of GG-B-383 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-lbb9bF = 999990b L9517b5 379 , MIL-T-11196F TABLE I. Components (contd) National Stoc

26、k Number uantity Item Ccanponent 10 Bit, wood-boring, auger, conforming to type I, class A, size 3/4 inch of CaG-B-38,3 1 ea. 1 ea. 11 Bit, wood-boring, auger, conforming to type I, class A, size 7/8 inch of GGG-B- 3 83 12 1 ea. Bit, wood-boring, auger, conforming to type I, class A, size 1 inch of

27、GGG-B-383 13 Blade, hand hacksaw, conforming to type I, grade A, class 2, size 10 inch, 24 teth of GGG-B-451 1 ea. 14 Brace, bit, ratchet, conforming to type I, class 2, style A, 10 inch sweep Of GGG-B-671 10 ea. O 15 Carrier, tool, leather, conforming to CCG-C- 1520 5140-01-168-4474 2 ea. 1 ea. 16

28、Chisel, hand, cold, conforming to type IV, class 1, 1/2 inch width, 6 inch length of OGG-C-313 17 18 Chisel, wooctworking, conforming to type I, class 3 of GGG-C-311 5110-00-585-8427 1 ea. 1 ea. Chisel, woodworking, conforming to type I, class 4, style C, 1 inch width, 6 inch blade of CGG-C-311 19 2

29、0 21 22 Crimping tool, terminal, hand (see 6.3) 5120-00-278-2423 5110-00-288-6520 2 ea. 2 ea. Cutter, tube, conforming to type II, class I of GGG-C-771 Drill, masonry, hand, 314 inch diameter, 12 inch length, conforming to A-A-2555 5110-00-236-2046 1 ea. Drill, masonry, hand, 3/8 inch diameter, 12 i

30、nch length, conforming to A-8-2555 5110-00-236-2047 1 ea. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-11196F TABLE I. Cmnents (contd) Item Canpnent National Stock Number Quantity 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 Drill, push, m

31、etal handle, conforming to A-A-2552 Extension, bit, square socket, confonn- ing to type IV, style A, 5/8 inch diameter, 18 inch length of aX-B-671 File, hand, bastard, half round, 8 inch length, conforming to A-A-2312 File, hand, mill, bastard cut, flat, 10 inch length, conforming to A-A-2316 File,

32、hand, bastard, round, 12 inch length, conforming to A-A-2318 Flashlight, 2 cell, straight, plastic, conforming to MIL-F-3747 capacity, conforming to A-A-453 Erame, hand hacksaw, 10 to 12 inch blade Gloves, leather, conforming to MIL-G-2 36 6 Harmrer, hand, carpenters, 16 ounce, fiberglass handle, co

33、nforming to We, wocd, conforming to NN-H-85 Key set, socket head, conforming to A-A- 1307 GG-K-275 Knife, pocket, clevis, conforming to (xK;-K-484 Light test (see 6.4) mel and plimib, conforming to type IV Multimeter, clamp-on, conforming to of GGG-L-211 type II of MIL-M-9983 5110-00-293-3410 5110-0

34、0-241-9150 5110-00-242-5385 5110-00-234-6557 6230-00-270-5418 5110-00-289-9657 8415-00-268-7869 5120-00-892-5485 5110-00-595-8325 5120-00-935-4641 5110-00-240-5943 6625-00-224-6246 5120-00-516-3356 6625-00-063-0896 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 2 ea. 1 ea. 2 pair 2 ea. 1 ea. 1 set 2 ea. 2 ea. 2 M. 1

35、 ea. . 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-11196F TABLE I. Components (contd) National Item Component Stock Number Quantity 38 39 40 41 42 43 44 e 45 46 47 48 49 50 Padlock set 5340-01-052-0671 Pliers, diagonal cutting, 6 inch 511

36、0-00-224-1532 length, conforming to A-A-2330 Pliers, straight-nose, regular, 6 inch 5120-00-223-7396 length, conforming to Ox-P-471 Pliers, linemans, conforming to type I, 5120-00-239-8251 class 1, 8 inch length of ANSI B107.20 Pliers, bending, wire, conforming to 5120-00-184-9403 type III, class 4,

37、 style B, 6-1/2 inch length of ANSI B107.13 Pliers, slip joint angle-nose, grooved, 5120-00-781-0819 12 inch length, conforming to GCG-P-471 Pouch, linemans, belt, looped (see 6.5) 5140-01-012-7038 Puller, fuse, 0-30 amp, conforming to type I, size 1, 1/4 inch through 1/2 inch diameter of W-P-796 Pu

38、nch and die, conforming to type I, 5110-00-288-8737 Mch and die, conforming to type I, 5110-00-243-1645 Punch and die, conforming to type I, 5110-00-293-0108 Punch and die, conforming to type I, 5110-00-293-0103 class 1, size 1/2 of GGG-P-836 class 1, size 3/4 of Ox-P-836 class 1, size 1 of GGG-P-83

39、6 class 1, size 1-1/4 of GGG-P-836 Rasp, hand, conforming to A-A-2329 5110-00-233-9718 Roll, tools 5140-00-408-1905 Rule, folding, wood, 6 foot length, 5120-00-293-3393 conforming to GGG-R-791 Saw, hand, nested, 16 to 18 inches in 5110-00-293-0090 length, conforming to GGG-S-65 1 ea. 2 ea. 2 ea. 2 e

40、a. 2 ea. 2 ea. 2 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea. 2 ea. 1 set 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-LLLSbF = 9Ob L517b8 088 MIL-T-11196F TABLE I. Components (contd) National Item Component Stock Munber Quantity 51 52 53

41、 54 55 56 57 58 59 60 61 62 63 Screwdriver, straight, conforming to type I, class 1, design A, 3 inch length of ANSI B107.15 Screwdriver, straight, conforming to type I, class 1, design A, 5 inch length of ANSI B107.15 Screwdriver, straight, conforming to type I, class 1, design A, 8 inch length of

42、ANSI B107.15 Screwdriver, cross tip, conforming to type II, design A, size 1, 3 inch length of ANSI B107.15 Screwdriver, cross tip, conforming to type II, design A, size 3, 6 inch length of ANSI B107.15 Stripper, cable, hand Tape, fish, steel, conforming to type I, style 1, size 6, 100 foot length o

43、f GGG-T-1310 Tape, measuring, steel, conforming to type V, class A, style 1, 50 foot length of GOG-T-106 Tool box, steel, galvanized material Tool, crimping (pliers), conforming to class 1, type I, AWG 10 through 22, 10 inch length of MIL-C-22520 lbrch kit, soldering, propane gas, Conforming to A-A-

44、51128 Wrench, adjustable, open end, conforming to size 10 of A-A-2344 Wrench, adjustable, open end, conforming to size 18 of A-A-2344 5120-00-236-2127 5120-00-278-1270 5120-00-260-4837 5120-00-240-8716 5120-00-234-8912 5110-01-218-5828 5120-00-287-4678 5120-00-150-2920 5140-01-237-3233 5120-00-449-8

45、083 5120-00-240-1414 2 ea. 2 ea. 2 ea. 2 ea. 2 ea. 2 ea. 1 ea. 2 ea. 2 ea. 1 ea. 1 ea. 2 ea. 1 ea. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-LLLSbF 9999906 1951769 TL4 MIL-T-11196F TABLE I. Components (contd) a National Item Component S

46、tock Number Quantity 64 Wrench, pipe, adjustable, conforming to 1 ea. type II, class A, 10 inch length of -W-651 65 Wrench, pipe, adjustable, conforming to type II, class A, 18 inch length of GGG-W-651 1 ea. 3.3 Finish. Tool kit components and tool box shall be finished in accordance with the applic

47、able finish requirements of referenced documents. Those items not covered by a referenced document shall be finished in accordance with the mufacturers current comercial practice. In no case shall the use of cadmium plating be allowed. marked in accordance with referenced documents or the manufactur

48、ers name or readily identifiable trademark, as applicable. 3.4 Markinq for identification. Tool kit components and tool box shall be 3.5 Workmanship. The finished tool kits and catpnents shall mt the workmanship requirements of referenced documents. 4. QUALITY ASSURANCE PRVISIONS O 4.1 Responsibilit

49、y for inswction. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor my use his ain or any other facilities suitable for the perfor- mce of the inspection requirements speci