ARMY MIL-T-13300 E-1991 TRUCKS HOPPER COAL DELIVERY CONVEYOR TYPE DIESEL ENGINE DRIVEN 24 000 GVW 4X2 AND 39 500 GVW 6X4 MODIFIED COMMERCIAL《商用改装载量为24 10 4X2型和载量为39500 6X4型 柴油发动机驱动.pdf

1、NIL-T-13300E 23 9999906 0471849 T - - I NOT MEASUREMENT SENSITIVE I MIL-T-l3300E(AT) # Pehria;? 1991 MIL-T-l330OD(AT) 10 October 1985 . SUPERSEDING MILITARY SPECIFICATION TRUCKS, HOPPER: COAL DELIVERY, CONVEYOR TYPE, DIESEL ENGINE DRIVEN, 24,000 GVW, 4x2 AND 39,500 GVW, 6x4, MODIFIED COMMERCIAL This

2、 specification is approved for use by the Army Tank- Automotive Command, Department of the Army, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE * 1.1 Score. This specification covers 4x2 and 6x4 diesel engine driven commercial conveyor type coal deliv

3、ery trucks. Vehicles procured under this specification are commercial items which are warranted by the manufacturer as specified in acquisition documents. . Vehicles shall be of the following sizes, as 1.2 Classification II specified (see 6.2): Size I - 24,000 GW, 4x2 Size II - 39,500 GW, 6x4 2, APP

4、LICAi3J.d DOCUMENTS 2.1 Government doc-. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: US Army Tank-Automotive Command, AWN: AMSTA-UKD, Warren, MI 48397-5000 by using the self-addressed Standa

5、rdization Document Improvement Propasal Form (DD Form 1426) appearing at the end of this document or by letter. l i AMSG N/A I FSC-2320 1 Approved for public release; distributian in unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-i3

6、300E(AT) . The following * 2.1.1 Specification4. Fitandards spec.ifications, standards and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department ,of Defense Index of Specificati

7、ons and Standards (WDISS), and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL W-B-I31 :# W-F-800 - Battery, Storage: Vehicular, Ignition, - Fuel Oil, Diesel. Lighting and Starting, MILITARY * MIL-P-514 - Plates, Identification, Instruction and * MIL-T-5624 - Turbine

8、Fuel, Aviation, Grades JP-4 and st: MIL-T-83133 - Turbine Fuel, Aviation, Kerosene Type, Grade Marking, Blank. JP-5 - JP-8 - STANDARDS FEDERAL - Rustproofing of Commercial (Nontactical) Vehicles - PED-STD-297 MILITARY MIL-STD-1223 - Nontactical Wheeled Vehicles, Treatment ., Painting, Identification

9、 Marking and Data Plate Standards. * specifications, standards, and handbooks are available from the Naval Publications and Forms Center, Military Specifications and Standards, Bldg 4D, 700 Robbins Avenue, Philadelphia, FA 19111-5094.) (Unless otherwise indicated, copies of federal and military * 2.

10、1.2 Wer Governuen$ docw-gs? and mblicatians . The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. the issues are those cited inthe solicitation. * DEPARTMENT OF DEFENSE Unless otherwise specified, Department of Defense Ind

11、ex of Specifications and Standards (WDISS). (Copies of the DODISC are available on a yearly subscription basis either from the Government Printing Office for hard copy, or microfiche copies are available from the Director, Navy Publication and Printing Service Office, 700 Robbins Avenue, Philadelphi

12、a, PA 19111-5093.) h L Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-UEPARTMl3NT OF TRANSWRTATION (DOT) Federal Motor Carrier Safety Regulationa, Federal Motor Vehicle Safety Standards. .e Federal Regulations, 49 CFR, and the Federal Register, and

13、should be addressed to the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402.) (Application for copies of DOT publications should reference the Code of ENVIRONMENTAL PROTECTION AGENCY (EPA) Control of Air Pollution from New Motor Vehicles and New Motor Noise Emissi

14、on Standards for Transportation Equipment - Medium and Vehicle Engines. Heavy Trucks- (Application for copies of EPA publications should reference the Code of Federal Regulations 40 CFR and the Federal Register and should be addressed to the Superintendent of Documents, U.S. Government Printing Offi

15、ce, Washington, D.C. 20402.) * 2.2 Non - Govermnt wblicqtinm The following documents form a part o this document to the extent specified herein. the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. the issues of documents not listed

16、 in the DODISS are the issues of the documents cited in the solicitation see 6.2). Unless otherwise specified, Unless otherwise specified, * THE EUROPEAN TIRE AND RIM TECHNICAL ORGANISATION (ETRTO) Standards Manual I (Application for copies of the ETRTO publications should be addressed to the Eupope

17、an Tyre and Rim Technical Organisation, 32, Avenue Brugmann, 1060 Brussels, Belgium.) SAE, Inc, 5245 55 1G - Hydraulic Hose Fittings (DD adopted). 5517 - Hydraulic Hose. 5537 - Storage Batteries (WD adopted). 5551 - Performance Levels and Methods of SAE Standards and Recommended Practices. - Engine

18、Rating Code 7 Spark Ignition. Measurement of Electromagnetic Radiation from Vehicles and Devices (30-1000 MHz). 5588 - Turn Signal Lamps. 5589 - Turn Signal Switch. J682 JG3 - Tire Chain Clearance - Trucks, Buses and - Rear Wheel Splash and Stone Throw. Combinations of Vehicles (DOD adopted). I 3 Pr

19、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-13300E 23 W 9999906 0471852 T W 5688 5704 5816 J931 JI349 - Truck Ability Prediction Procedures (LOR - Openings for Six- and Eight-Bolt Truck adopted ) Transmission Mounted Power Take-offs (DOD adop

20、ted). Diese1 - - Engine Test Code - Spark Ignition and - Hydraulic Power Circuit Filtration. - Engine Power Test Code - Spark Ignition and Diese 1 - (Application for copies of CAE publications should be addressed to SAE, Inc., 400 Commonwealth Drive, Warrendale, PA 15096. ) THE TIRE AND RIM ASSOCIAT

21、ION, INC. Year Book (Application for copies of The Tire and Rim Association publications should be addressed to the Tire and Rim Association, Inc., 175 Montrose West Ave, Copley, OH 44321.) * from the organizations that prepare or distribute the documents. documents also may be available in or throu

22、gh libraries or other informational services-) (Non-Government standards and other publications are normally available These * 2.3 Order of srecedwm. In the event of a conflict between the text of this document a.rid the references cited herein, the text of this document shall take precedence- Nothi

23、ng in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained- 3. REQUIREMENTS X 3.1 iFI device . Not less than two hoolrs, loops, or pins, or a single center mounted towing eye for towing the vehicle shall be furnished on the front of the veh

24、icle. When specified (see 6.2), not less than two hooks, loops, or pins Shall be furnished on the rear. frame rail mounted or reinforced back to each frame rail. % 3.1.1.6 -. Rear wheels shall be provided with rigid splash guards in front and rubber mudflaps at the rear. A metal strip not less than

25、1/8-inch thick and not less than one inch wide, extending the entire width of the mud flap, shall be installed to prevent the bolt heads or the bolt nuts from damaging the mud flap. flaps, tabs or clips with minimum surface contact dimensions of 1 inch high by 1-1/4 inch wide by 3/32 inch thick shal

26、l be furnished at each bolt. All splash shield and mud flap installations, front and rear, shall conform to the rear wheel splash and stone throw protection provisions of CAE 5682. * 3.1.1.7 the body; and a full complement of,fuel, lubricants, and coolant. 3.2.5 .t: 3.2.9 BcceibiliLY shall permit ac

27、cess for routine servicing and shall permit access for replacement and adjustment of component parts and accessories with minimal disturbance of other components and systems. The design of the vehicle and optional equipment 48. * 3.2.10 er . . A full flow or combination full flow end by-pass oil fil

28、ter with replacement element shall be furnished. 3.4.1.3 Governa . An engine governor shall be furnished, set, and sealed to liait the engine to the engine manufacturers recommended operating symed - 4; 3.4.1.4 kl system . The cooling system shall maintain the engine coolant at a temperature below t

29、he boiling point with the vehicle loaded to GVW and operated at an altitude of 10,000 feet above sea level or in an ambient air temperature of not less than 125 degrees Fahrenheit (OF). coolant system shall include a surge tank or a coolant recovery reservoir of not less than two-quart capacity. acc

30、ess door shall be provided to allow verification of the coolant level. The On tilt cab modela, a radiator servicing :K 3.4.1.5 W-ure contral. Thermostatic control of engine coolant temperature shall be provided- On diesel engine driven vehicles, control shall include complete thermostatic control of

31、 all coolant flow through the radiator, :J( 3.4.1.6 Fan c.lutxh. A fan clutch shall be provided. The fan clutch shall reduce the fan speed automatically when the fan is not required for engine cooling. The fan clutch shall be asbestos free. 3.4.1.7 SiLicone rubber bnaes . When specified (see 6.2), s

32、ilicone rubber radiatorland heater hoses shall be furnished. :* 3.4.1.8 Power plant hea$er,s .andAuel warm . When specified (see 6.2), coolant heater, engine oil heater, and fuel warmer shall be provided. Unless otherwise specified (see 6.2), a battery heater shall be provided when power plant heate

33、rs are specified. c.urrent (ac) and shall be wired through a junction block, including a fuse or circuit breaker, to a single three-pronged (male), weatherproof, slave receptacle for receiving external power and grounding the vehicle. A three-wire connecting cable, 25 feet long and of adequate line

34、capacity to supply power for all heater units simultaneously, shall be furnished. The connecting cable shall include a matching female connector at the vehicle end and a standard, three-pronged (two power plus one ground) male connector at the other end. Electrical apparatus shall conform to Federal

35、 Motor Carrier Safety Regulation 393.77()(7). cable shall withstand normal operating stresses in low ambient air t2mperatures (down to minus 60oF) without cracking or loss of dielectric capacity. vehicle component operation, and without loose excess wire. Provisions for stowage of the cable shall be

36、 provided in the vehicle cab. furnislied as follows: Heaters shall operate on 110-volt alternating The electrical insulation of the connecting All heater lead wires shall be installed without interfering with Heaters shall be Provided by IHSNot for ResaleNo reproduction or networking permitted witho

37、ut license from IHS-,-,-A coolant heater, 1500-watt minimum rating, shall be installed in the engine block or lower, coolant, inlet hose. Engine thermostat with an operating range of 170oF to 195oF shall be installed. An oil pan heater of the permanent external surface mount, permanent in-pan mount,

38、 or immersion type that meets the following require- ments, shall be installed: (1) Not less than 22 watts per quart heating capacity (2) (3) (4) Provision for mounting below minimum service oil level. The battery heater shall have a capacity adequate to maintain the battery electrolyte at a tempera

39、ture of not less than 1OoF during vehicle exposure in ambient air temperatures as low as minus 600F and shall embody a thermostat to limit the temperature of the electrolyte to not more than 80oF- A fuel warmer or pre-heater shall be provided to prevent clogging of fuel filters due to wax crystalliz

40、ation in the fuel, warmer shall use engine coolant to transfer sufficient heat to the diesel fuel to heat it from an inlet temperature of minus 40oF to an outlet temperature of plus 9oF, with a flow rate not less than the maximum fuel demand of the engine fuel system. shutoff valve shall be provided

41、 for the coolant inlet side of the fuel warmer unit Not more than 18 watts per square inch heating capacity Thermal balance design or thermostat control providing for uninterrupted operation The fuel A coolant * 3.4.1.9 Euel fired enwbeater . When specified (see 6.2), a diesel fuel fired engiifie wa

42、ter heater shall be furnished to preheat the engine. The heater shall include a timer, a thermostat and circulating pump; and shall be c.onnected directly across the engine coolant inlet and outlet. shall be capable of starting and operating at minus 600F and shall heat the engine to plus 40oF from

43、minus 60oF in not more than 1 hour. shall be equipped with a light, visible to the driver, to indicate that the pre.heater is operating . The heater The system 3.4.2 ElectrW svstern The electrical system shall be in accordance with Federal Motor Carrier Safety Regulations 393.27 through 393.31 and 3

44、33-33. * 3.4.2.1 Startine system - A 12- or 24-volt direct current (dc) starting system, with 12-volt dc lighting system, shall be furnished. Engine starting equipment shall include an ether starting system, glow plug or grid heater. If an ether system is furnished in lieu of a glow plug or grid hea

45、ter, it shall be of the measured shot type. Measured shot type ether systems shall be key operated or manually operated from the drivers compartment, and shall be inoperative with the engine warm. reservoir or“ not less than i2 fluid ounces shall be furnished. A reservoir need not be furnished- Comp

46、lete provisions for an ether 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-33300E 23 9999906 04738.58 O I *: 3.4.2.1.1 Alterriatar. Unless otherwise specified (see 6-21, a minimum f AI F - ampere alternator shall be furnished. The alternato

47、r output with the engine at engine idle speed shall be not less than 45 amperes, L 3.4.2.2 Uhjing. All vehicle lights, reflectors, and wiring shall conform to Federal Motor Carrier Safety Regulations 393.12, 393.13, 393.19, 393.20, and 393.22 through 393.26(d). mounted on the vertical surface of rub

48、 rails (unless recessed and fully protected) or mounted on vehicle bumwrs. Lights anci reflectors ahall not be 3: 3.4.2.3 . Turn signal lamps shall conform to SAE J588. Operating units shall conform to SAE 5589 class A and shall be mounted on the steering column. Turn signal units shall be installed

49、 in accordance with 6AE J588. indicators - Turn signal operating units shall have visible and audible type flash Y: 3.4.2.4 Batterles . Each battery shall be of 12-volt potential. The total reserve capacity rating and the total cold cranking ampere rating at OOF shall be not less than specified in table I. cranking ratings shall be in accordance with CAE 5537. the maintenance-free type having the maintenance-free characteristics listed in W-B-131. Reserve capacity a