ARMY MIL-T-13560 D-1981 TARGETS PASTEBOARD AND POLYETHYLENE《聚乙烯纸板目标》.pdf

1、MIL-T-13560D 27 May 1981 SUPERSEDING 10 December 1980, and MIL-T-13560B 28 December 1973 MIL-T-O01356OC(AR) MILITARY SPECIFICATION TARGETS, PASTEBOARD AND POLYETHYLENE This specification is approved for use by all Depart- ments and Agencies of the Department of Defense. 1. SCOPE 1.1 This specificati

2、on contains requirements not covered by the draw- ings, and provides quality assurance provisions for the fabrication, assem- bling and packaging for several types and sizes of pasteboard (ffberboard) and polyethylene targets. (See 6.3) 2. APPLICABLE DOCUMENTS 2.1 Issues of documents. The following

3、documents of the issue in effect on date of invitation for bids or request for proposal, form a part of this specification to the extent specified herein. SPECIFICATIONS * MILITARY I MIL-P-14232 Parts, Equipment and Tools for Army MIL-14- 6 3 1 5 O Materiel, Packaging of Weapons and Support Materiel

4、 Standard Quality Assurance Provisions for . FSC 6920 I f- THIS DOCUMENT CONTAINS ao PAGES. 64 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-T-L3560D 67 W 9977906 0378507 3 MIL-T-13560D FEDERAL FEDERAL TEST METHOD STANDARD NO. 191 - TEXTILE TE

5、ST METHODS MI LI TARY MIL-STD-105 Sampling Procedures and Tables for Inspection by Attributes. DRAWINGS (See 6.2) US ARMY ARMAMENT RESEARCH AND DEVELOPMENT COMMAND PRODUCT DRAWINGS 5175649 Disk, Bayonet Practice, Ml 6006881 Target, Trapezoidal 8426438 Target, Kneeling 8426556 Target, Prone 12002898

6、Target, Silhouette, Type “E“ Kneeling, 12002899 Target, Silhouette, Type “F“ Prone, Polyethylene Polyethylene PACKAGING DATA SHEETS P5175649 Disk, Bayonet Practice, Ml P6006881 Target, Trapezoidal P8426438 Packaging Data Sheet for Board, TargetE P8426556 Packaging Data Sheet for Board, Target, P1200

7、2898 Packaging Data Sheet for Target, P12002899 Packaging Data Sheet for Taget, Kneeling Prone Silhouette, Type “E“ Silhouette, Type “F“ Prone . (Copies of specifications, standards, drawings, and publications required by suppliers in connection with specific procurement functions should be obtained

8、 from the procuring activity or as directed by the contracting officer.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-33560D b7 7777706 0378530 T MIL- T- 135 60D 2.2 Other publications. The following docimients form a part of this specific

9、ation to the extent specified herein. Unless otherwise indicated, the issue in effect on the date of invitation for bids or request for proposal shall apply. TECHHICAL ASSOCIATICN OF THE PLP AND PAPER INDUSTRY STANDARDS T4 1 1 -OS -7 6 T477-TS47 T480-O 5-72 T49 1-SU-6 3 Thickness (caliper) of Paper

10、and Paperboard Blocking Resistance of Paper and Flexible Materials Specular Gloss of Paper and Paperboard at 75 Degrees Water Inmersion Test of Paperboard (Application for copies should be addressed to the Technical Association of the Pulp and Paper Industry, 1 Dunwoody Park, Atlanta, Ga 30338). AME

11、RICAN SOCIETY FOR TESTING AND MATERIALS e D747 Method of Test for Stiffness of Plastics by Means of a Cantilever Beam (Application for copies should be addressed to: -Anerhan Society for Testing and Materialsi 1916 Race Street, Philadelphia, PA 19103) 3. REQUIREMENTS 3.1 Material. Materiais shall be

12、 in accordance with Drawings (Dwgs.) 5175649, 6006881, 8426438, 8426556, 12002898 and 12002899, as applicable, all associated drawings, and all requirements specified in applicable specifications and standards. 3.2 Targets. The targets shall comply with all requirements specified in Dwgs. 5175649, 6

13、006881, 8426438, 8426556, 12002898 and 12002899, as applicable, all associated drawings, and all requirements specified in applicable specifications and standards. 3.3 Pasteboard targets . 3.3.1 Water absorption. The water absorption of the targets shall be a maximum of ten (10) percent when determi

14、ned as specified in 4.3.1.2. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - MIL-T-135bOD 67 W 7779706 037851L L . MIL-T-13560D 3.3.2 Blocking. The targets sall show no evidence of blocking (adhesion) when tested as specified in 4.3.1.3. 3.3.3 D

15、elamination. The target shall show no evidence of delamination, (separation of plies) exceeding one-eighth (i /8) inch from the edge of the target when tested as specified 4.3.1.4. 3.3.4 Stiffness (modulus of elasticity). The target shall have a minhum stiffness in the machine direction of 184,000 p

16、ounds per square inch (psi) when subjected to the stiffness test specified in 4.3.1.5. 3.3.5 Puncture resistance. The target shall have a minimum puncture resistance of forty (40) pounds when subjected to the water hersion test specified in 4.3.1.6. 3.3.6 Colorfastness to light. The color side of th

17、e target shall evidence acceptable colorfastness to light rating when tested as specified in 4.3.1.7. 3.3.7 - Gloss. 3.4 Workmanship. Pasteboard targets shall be free from foreign Targets shall be trimmed and The target shall have a maximum gloss value of twenty (20) units when tested as specified i

18、n 4.3.1.8. or undigested matter , discoloration, dirt or oil spots, holes, tears, wrinkles, chaff or scuff marks. shall have no ragged, torn, uneven, or crushed edges. All targets shall be clean and free of defects affecting serviceability including rough or broken edges, warpage, distortion, or mut

19、ilated areas. All required markings shall be neat and sharply defined. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection and standard quality assurance provisions. Unless otherwise specified herein or in the contract, the provisions of MU-W-63150 shall apply and are hereby made a par

20、t of this specificatson. _. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-: MIL-T-13560D 4.2 Lot formation. Unless otherwise specified in the contract, the lots shall be characterized by homogeneity and be in accordance with the lot formation req

21、uirements specified in MIL-STIE-105. Lots shall consist of unit packs of one type or kind of pasteboard or polyethylene target, as applicable. Each lot shall have been manufactured and packaged under one contract using essentially the same conditions during the same identifiable production period, a

22、nd submitted for acceptance by one supplier at one time. 4.2.1 Sampling for inspection and acceptance. Sampling for inspection and acceptance shall be performed in accordance with the provisions set forth in MIL-STD-105 except where otherwise indicated. 4.2.2 Inspection to be performed. Unless other

23、wise specified, inspection of the targets and packing shall be performed in accordance with the folldng tables (4.2.2.1 to 4.2.2.71, as applicable . /- =-y 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-E Y rl t5 t rl : 4 . h( * - -7 MIL-T-L35bOD

24、67 W 7777706 0378513 5 W aa 8: .- alal a* i .;i mm nLi Li *rl E Ba m *rl 8” a al E *rl w al a z a *rl YI lu a al E O 2; 2 I n O o Ln m N N 8 . s 8 . .:- -7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-V al 4 VI .d a W al 5 5 *rl 3 E Y FI O a In ri

25、 rl I &4 I 12 - i I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-135bOD b7 S. 7977706 0378520 2 - MIL-T-13560D 4.2.3 Inspection Equipment. The inspection equipment required to perform the examinations and tests prescribed herein is described

26、 in the Paragraph Re- ference/Inspection Method column in the tables starting with Paragraph 4.2.2.1. The contractor shall submit for approval inspection equipment designs in accord- ance with the terms of the contract, shall be satisfactory to the Contracting Officer. ment or procedures shall have

27、prior written approval of the Contracting Officer. Ail inspection equipment and procedures Any change in inspection equip- 4.3 Test methods and procedures. 4.3.1 Pasteboard targets. 4.3.1.1 Conditioning. The targets to be subjected to the following tests shall be conditioned for not less than forty-

28、eight.(48) hours at 73O - $. 2O F. and 50 - + 4% relative humidity. 4.3.1.2 Water absorption. Three (3) boxes of targets shall be selected from each lot. accordance with 4.3.1.1. water immersion test specified in Technical Association of the Pulp and Paper Industry standard (TAPPI), Method T491-SU.

29、percent. If the average in- crease in weight exceeds the requirement specified in 3.3.1, the lot shall be rejected. One (i) target shall be taken from each box and conditioned in The three (3) targets shall then be subjected to the Results shall be to the nearest 1.0 Immersion time shall be not less

30、 than 24 hours. 4.3.1.3 Blocking. Three (3) boxes of targets shall be selected from each lot. Three (3) targets shall be taken from each box and conditioned in accord- ance with 4.3.1.1. specified in TAPPI standard, Method T477-TS. - + 2O F, Relative humidity 75 + 2%, Pressure 2.0 p.s.i. If any set

31、of targets fails to comply with the requirement specified in 3.3.2, the lot shall be re- jected. The targets shall then be subjected to the blocking test Dry bulb temperature shall be 140 4.3.1.4 Delamination. Two (2) boxes of targets shall be selected from each lot. Two (2) targets shall be taken f

32、rom each box and conditioned in accordance with 4.3.1.1. The targets shall than be tested as follows: -_ 13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-L35bOD 67 777770b 03785211 4 W MIL-T- 13560D 4.3.1.4.1 Cold Temperature. The bottom four

33、 inches shall be cut from each target and conditioned at Oo F. for not less than 2 hours along with a 12-inch radius mandrel. After conditioning, and at the test temperature, the specimens shall be slowly bent around the mandrel and observed. for any signs of delamination or separation of plies. spe

34、cified in 3.3.3, the lot shall be rejected. If any specimen fails to comply with the requirement 4.3.1.4.2 Ambient temperature. Sample targets shall be selected as specified in 4.3.1.4. Specimens, as specified in 43.1.4.1,sha11 be immersed in water at 75O-+ 5O-F. for 24 hours. After removal from the

35、 water, the speTGuens shall be bent around the test mandrel at room temperature (730 F.) and observed for delamination (separation of contiguous layers of plies). specimen fails to comply with the requirement specified in 3.3.3, the lot shall be rejected. If any 4.3.1.5 Stiffness (modulus of elastic

36、ity). Three (3) boxes of Five (5) targets shall be targets shall be selected from each lot. taken from each box and conditioned in accordance with 4.3.1.1. Each set of five targets shall be subjected to the stiffness test in accordance with ASTM D 747 with the following exceptions: size shall be 2-b

37、y 6-inches, the span length shall be four inches, angular deflection shall be 5O and moment weight shall be 20 in.-lbs. for 24 hours. After immersion, excess water shall be carefully blotted from specimens, exercising care that the specimens are not flexed or compressed. be as follows: specimen The

38、specimens shall be measured and then immersed in water “he equation for determining stiffness shall 4L x s3 Stiffness (M.E.) psi - O “ DXWXT3 Where L = Load-scale reading X moment (in-lbs.) 100 x s 14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-f

39、lIL-T-13560D 69 7979906 0378522 b m MIL-T-lSTGOD S = span length (inches) D = angular deflection = 2s SIN. 4 W - width of specimen (inches) T = thickness of specimen (inches) O (inches) Results shall be to the nearest 100 psi. If the average stiffness of any set of five (5) targets fails to comply w

40、ith the requirement specified in 3.3.4, the lot shall be rejected. 4.3.1.6 Puncture resistance. Three (3) boxes of targets shall be selected from each lot. Five (5) targets shall be taken from each box and conditioned in accordance with 4,3.11, (4) inches square, shall be cut from each target. The s

41、pecimens shall be immersed for 24 hours in water at 750 + 50 F. After removal from the water, the specimen shall be blotted lighFly and tested. Any device ca- pable of applying a known amount of weight to a perpendfcularly mounted penetrator shall be satisfactory. rod tapered to a sharp point in 3/4

42、 inch. on a wooden or metal block (approx. 3 inches square and :i inch thick) with a 1/2 to 1 inch diameter hole through the 1 inch thickness. sistance to puncture shall be measured by applying the load in 5-pound increments to the penetrator centered over the hole. Complete penetra- tion should tak

43、e place in less than 5 seconds. f the specimen is not penetrated fully in 5 seconds, the penetrator shall be moved to another section of the specimen and an additional 5-pound weight added. imum amount of weight that penetrates each specimen in 5 seconds or less shall be recorded. specimens. One (i)

44、 specimen each four The penetrator shall be a 0,30-inch The specimens shall be placed The re- The min- This procedure shall be repeated on-all remaining Results shall be to the nearest pound. If the average puncture resfstance of any set of five (5) specimens fails to comply with the requirement cpe

45、- cified in 3.3.5, the lot shall be rejected. 4.3.1.7 Colorfastness to light. Three (3) boxes of targets shall be selected from each lot. One (i) target shall be taken from each box and and conditioned in accordance with 4.3.1.1. The three (3) targets shall then be tested in accordance with FED TEST

46、 METHOD STD-191, Method 5660. Results shall be interpreted as described in, FED TEST METHOD STD-191, Method 5662, the “No standard sample“ evaluation procedure. (See 6.4). If any target fails to comply with the requirement specified in 3.3.6, thelot shall be rejected. of twenty (20) hours. The expos

47、ure to light tbe shall be a minhum 15 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-L3560D 67 W 7777906 0378523 8 W MIL-T- 13560D 4.3.1.8 Gloss. Three (3) boxes of targets shall be selected Five (5) targets shall be taken from each box and -

48、from each lot. conditioned ia accordance with 4.3.1.1. subjected to the gloss determination specified in TAPPI standard Method T480-S. to comply with the requirement specified in 3.3.7, the lot shall be rejected. Results shall be to the nearest 0.1 unit. The targets shall then be If the average of a

49、ny set of five (5) targets fails _ . -z=:.e2.c - 4.3.1.9 Thickness. Ten (10) boxes of targets shall be selected from each lot. conditioned in accordance with 4.3.1.1. The thickness of each target shall then be determined in accordance with TAPPI standard Method T4114S. Measurements shall be to the nearest 0.001 inch. If the average thickness of the ten (1