ImageVerifierCode 换一换
格式:PDF , 页数:39 ,大小:1.27MB ,
资源ID:448517      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-448517.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ARMY MIL-T-3901E-1981 TROUSERS FIREMEN'S.pdf)为本站会员(sofeeling205)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

ARMY MIL-T-3901E-1981 TROUSERS FIREMEN'S.pdf

1、MIL-T-3901E 30 December 1981 SUPERSEDING MIL-T-390lD 9 September 1977 MILITARY SPECIFICATION TROUSERS, FIREMANS This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers firemans trouser with liner. 1.2 Classiic

2、ation+ The trousers shall be of one type in the following sizes as specified (see 6.2): Schedule of sizes 32 x 31 34 x 33 32 x 32 36 x 31 32 x 33 36 x 32 34 x 31 36 x 33 34 x 32 38 x 31 38 x 32 42 x 31 38 x 33 42 x 32 40 x 31 42 x 33 40 x 32 44 x 31 40 x 33 2. APPLICABLE DOCUMENTS * 2.1 Issues of do

3、cuments. The following documents, of the issue-in effect on date of invitation for bids or request for proposal, form a part of this specification to the extent specified herein. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this

4、document should be addressed to: US Army Naticlc Research and Development Laboratories, Natick, MA 01760 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this docu- ment or by letter. FSC 8415 G Provided by IHSNot for ResaleNo reproduct

5、ion or networking permitted without license from IHS-,-,-MIL-T-3 901E SPECIFICATIONS FEDERAL V-T-276 FF-R-5 56 Thread, Cotton Rivet, Solid, Small; Rivet, Split, Small; Rivet Tubular, Small; Burr; and Cap, Rivet; General Purpose Washers, Flat (Plain) Leather, Cattlehide, Strap, Vegetable Tanned Paper

6、, Kraft, Wrapping Label: For Clothing, Equipage, and Tentage Boxes, Shipping, Fiberboard (General Use) FF-W-92 JM-L-2 7 1 UU-P-268 DDD-L-20 PPP-B-636 MIL ITAY MIL-B-286 MIL-F-495 MIL-B-543 MIL-T-3530 Buttons, Tack; and Tack, Button Finish, Chemical, Black, for Copper Alloys Buckles, Tongueless and W

7、eb Strap Thread and Twine; Mildew Resistant or Water Suspenders, Trousers (Suspenders, Flying Suit) Fasteners, Snap Phosphate Coating, Heavy Maganese or Zinc Base Cloth, Sateen, Cotton, Flame Resistant Treated Cloth, Coated: Polyester/Cotton, Polyesterhayon; Polyvinyl Chloride or Polychloroprene Coa

8、ted Cloth, Plain or Pajama Check Weave, Aramid Thread, Aramid Cloth, Coated or Bonded, Reflective Batting, Aramid or Nonvoloid Fiber, Quilted Repellent Treated (For Ferrous Metals) MIL-S-6790 MIL-F-10884 DOD-P-16232 MIL-C-43122 MIL-C-43410 MIL-C-43774 MIL-T-43636 MIL-C-43 708 MIL-B-81813 STANDARDS F

9、EDERAL FED-STD-751 MILITARY MIL-STD-105 MIL-STD-129 Stitches, Seams and Stitchings Sampling Procedures and Tables for Inspection by Attributes - Marking for Shipment and Storage MIL-STD-1188 - Commercial Packaging of Supplies and Equipment 2 Provided by IHSNot for ResaleNo reproduction or networking

10、 permitted without license from IHS-,-,-MIL-T-3901E (Copies of specifications, standards, drawings and publications required by contractors in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer.) 3. REQUIREMENTS 3.1

11、 Guide sample. Samples, when furnished, are solely for guidance and information to the contractor (see 6.3). appear in. the sample, in which case, the specification shall govern. Variations from the specification may * 3.2 Materials (see 6.4). 3.2.1 Basic material. The material for the outer shell s

12、hall be flame resistant , treated cotton sateen cloth conforming to class 2 of MIL-C-43122. * * 3.2.2 Liner material. The material for the outer liner shall be a coated cloth conforming to MIL-C-43410. The color of the outer liner shall be natural or white. * 3.2.3 Liner. The material for the liner

13、shall be quilted batting conforming to MIL-B-818rThe color of the outer covering cloth shall be Olive Green 106 with the needle stitching thread of the dumbbell pattern (side facing wearer) being of an Olive Drab color and the bobbin thread (facing trouser) being a natural color thread. The minimum

14、width of the batting shall be 24 inches. * 3.2.4 Binding. The aramid cloth for binding waist, fly opening and leg bottoms shall be dyed OG-106, conforming to MIL-C-43774. Je 3.2.5 Reflectorized/fluorescent cloth. The reflectorizedlfluorescent cloth shall conform to type I, class 3 or type II, class

15、2 of MIL-C-43708. * 3.2.6 Thread. The thread for seaming and stitching, where required, shall be aramid, size E and B conforming to type I of MIL-T-43636. * 3.2.6.1 Color, * * 3.2.6.1.1 Outer shell. The thread color for the outer shell shall be Olive Drab S-1 (C.A. 66022). . * 3.2.6.1.2 Liner. The t

16、hread color for the liner shall be Olive Drab S-1 (C.A. 66022), or be natural color. * 3.2.6.1.3 Reflectorized/fluorescent strips. The thread color for the strips shall be natural. * 3.2.6.2 Colorfastness. The Olive Drab S-1 (C.A. 66022) thread shall show fastness to laundering (after three cycles)

17、equal to or better than the standard sample. fastness to laundering. fien no standard sample is available, the colored thread shall show -“good“ 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- -I - MIL-T-370LE BY = 9777706 0374Li72 3 MIL-T-3901E *

18、 3.2.7 Labels. Each trouser liner shall have a personal identification, size, identification and instruction label. All labels shall conform to DDD-L-20. The fastness ta laundering requirements of DDD-L-20 shall apply * 3.2.7.1 Identification label. The identification label shall conform to type VI,

19、 class 1. * 3.2.7.2 Size label. The size label shall conform to type VI, class 2. 3.2.7.3 Combination label. The identification label and the size label may be combined for the trouser liner. * * 3.2.7.4 Personal identification label. The personal identification label shall conform to type VI, class

20、 10. * 3.2.7.5 Instruction label. The instruction label shall conform to type VI, clase * 3, except that the contract number shall be included directly under the item description. The body of the instruction label shall be as follows: TROUSERS, FIREMAN s For maximum wearing comfort, type 1 Suspender

21、s, Trousers (Suspenders, Flying Suit) canfbrming to MIL-S-6790 be worn with trousers. DO NOT REMOVE THIS LABEL (FSN 8440-00-275-5764) should Launder using Formula 1 of TM-10-280 Warning: In laundering, do not use acid sour rinse. The rinse bleaches out the flame proofing agent in the garment . 3.2.8

22、 Leather. The leather for the straps and strap reinforcement pieces shall be vegetable-tanned cattlehide, type I, II, III or IV, class 2, 4/64 to 5/64 inch thick, conforming to KK-L-271. leather may be finished on the grain side with a light application of finish and dye, containing only sufficient

23、pigment to assist in making the color uniform. The color shall be either black or russet. The 32.9 Snap fastener. The snap fastener for attachment of the outer shell to the trouser liner shall be a complete snap fastener (male and female), and shall consist of button, 24-line, size 1, and socket for

24、 the female half; and a size 1 eyelet with stud for the male half, conforming to style 2, finish 2 of MIL-F-10884. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-3901E 3.2.10 Rivets, tubular with caps or washers. The rivets shall be 1/8 inch

25、 nominal size, 3/16 and 3/8 inch minimal length, conforming to type XII, class 1, grade F of FF-R-556 except that they shall be drilled to the head and the inside of the rivet shank shall be chamfered. The caps shall conform to type II, grade F of FF-R-556. When washers are used in lieu of caps for

26、securing the rivets, they shall fit the rivets and conform to type A, grade 11, class E, of FF-W-92, The rivets, caps, and washers shall have a black chemical finish conforming to MIL-F-495. The 3/16 inch length rivet shall be used to attach the loop to the waistband and the clasp to the adjusting s

27、trap. The 3/8 inch length shall be used to attach the buckle strap and the adjusting strap to the waistband. 3.2.11 Buckle. The buckle shall be tongueless, two-bar, steel, conforming to type II, style 4, construction B, class 3, size 3/4 inch, of MIL-B-543. t 3.2.12 Buttons. The buttons shall be typ

28、e I, size 27-line with type IX tack, size 14-line by 0.406 inch prong length, conforming to MIL-B-285. * 3.2.13 Clasp and take-up loop. The clasp and take-up loop shall be either brass conforming to figure 3, or steel conforming to figure 4 of this specification. * 3.2.13.1 Finish-. * 3.2.13.1.1 Bra

29、ss. The brass clasp and take-up loop shall have a black chemical finish conforming to MIL-F-495. * 3.2.13.1.2 Steel. The steel clasp and take-up ldop shall have a phosphate coat- ing conforming to type pi or 2, class 1 or 2 of DOD-P-16232. * 3.3 Design. The trousers consist of an outer shell with a

30、quilted aramid batting liner covered with a vapor barrier of rubber coated fabric. The outer trouser has a wide fly with snap fastener closure, waist adjustment strap with clasp and loop, two hip patch pockets with flaps and snap fasteners, and metal suspender ,buttons. liner is attached permanently

31、 to the inside of the outer shell at the waistband and with snap fasteners at inseams and outseams of legs (figures 1 and 2). There are horizontal reflectorized/fluor-escent cloth strips permanently stitched around the bottoms of the legs. O The 3.4 Figures. Figures 1 and 2 are furnished for informa

32、tion purposes only. To the extent of any inconsistencies between the written specification and the figures, the written specification shall control. * 3.5 Patterns. Standard patterns which provide an allowance of 3/8 inch for single needle and safety-st3tch seams and 1/2 inch for double needle seams

33、 will be furnished by the Government. The Government patterns, which show directional lines and markings for proper assembly, shall not be altered in anyway and are to be used for a guide for cutting the working patterns. identical to the Government patterns. The working patterns shall be 5 Provided

34、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-3901E 3.5.1 List of pattern parts. The trouser shall be cut from the materials speci- fied in accordance with the number of parts indicated in table I. TABLE I. List of pattern parts Mat er ia1 Pattern no

35、menclature Cut: Darts Flame resistant cotton sateen Coated cloth Aramid batting Leather OUTER SHELL Front Back Right fly Left fly Pocket Pocket flap Waistband lining LINING Front Back 2 2 Front Back Buckle strap Adjusting strap 3.6 Construction. * 3.6.1 Stitches, seams and stitching. All stitches, s

36、eams and stitching shall conform to FED-STD-751. as specified in table I. that no raw edges, run-Offs, twists, pleats, puckers or open seams will result. Where two or more methods for seams or stitch types are given for the same part of an operation, any one of them may be used. Where stitch type 40

37、1, 504 or 505 are used, the looper thread shall be on the inside of the trousers. start and finish evenly. Unless otherwise indicated, the gage of stitching for the double-lapped, double-stitched seams shall be 3/16 to 5/16 inch. indicated in table II, double-lapped, double-stitched seams may be lap

38、ped in either direction. The type of seam, stitching and stitches per inch shall be Seam allowances shall be maintained with seams sewn so All seams shall Unless otherwise I * 3.6.1.1 Type 301 stitching. Ends of all stitchings shall be backstitched or overstitched not less than 1/4 inch except where

39、 ends are turned under or caught in other seams or stitching. Ends of a continuous line of stitching shall overlap not less than 1/2 inch. Thread tensions shall be maintained so that there will be no loose or top thread, or excessively tight stitching resulting in puckering of the materials sewn. Th

40、e lock shall be imbedded in the materials sewed. 6 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-a * 3.6.1.1.1 Repairs of type 301 stitching. MIL-T-3901E * 3.6.1.1.1.1 Quilted batting stitching. Broken stitches of the quilting pattern may be repa

41、ired by stitching back of each end of break not less than 1 inch. * 3.6.1.1.1.2 Trouser and liner fabrication stitching. a. When thread breaks or bobbin run-outs occur during stitching, the Stitching shall be repaired by restarting the stitching a minimum of 1/2 inchln back of the stitching. - i/ b.

42、 Thread breaks, or two or more consecutive skipped or run-off stitches noted during inspection of the item shall be repaired by overstitching. ing shall start a minimum of 1/2 inch in back of the defective area, continue over the defective area, and continue a minimum of 1/2 inch beyond the defectiv

43、e area onto the existing stitching. by removing the defective stitching without damaging the materials, and restitching in the required manner. - l/ The stitch- . 5 Loose or excessively tight stitching shall be repaired - l/ When making the above repairs, the ends of the stitching are not required t

44、o be backstitched. * 3.6.1.2 Type 401, 504 and 505 stitching. Thread tension shall be maintained so that there will be no loose or excessively tight stitching resulting in puckering of the materials sewn. All repairs shall be in accordance with 3.6.1.1.la. and. 3.6.1.1.lb. Type 301 stitching may be

45、used in repairing type 401 stitching. * 3.6.1.3 Thread ends. All thread ends shall be trimmed to 1/4 inch maximum length. * 3.6.2 Bartacking. Bartacking shall be 1/2 - + 1/16 inch in length and 1/8 + 1/32 Bartacking shall be free from thread inch in width and shall contain 28 stitches. breaks and lo

46、ose or tight stitching. - * 3.6.3 Setting of snap fasteners. A hole shall be prepunched to receive the button and eyelet components of the snap fasteners. the outside diameter of the button and eyelet barrels so that the barrel must be with the button or eyelet barrel. cutting the adjacent materials

47、 and no more than three splits shall occur in the button or eyelet barrels. The hole shall be smaller than I I forced through the hole. The hole shall not be punched in the setting operation The fasteners shall be securely clinched without 3.6.4 Repairs. trouser assembly. Repairs such as mends, darn

48、s or patches shall not be made to the * 3.7 Manufacturing operations requirements. The trousers shall be manufactured in accordance with operation requirements specified in table II. The contractor is not required to follow the exact sequence of operations. holding stitching used to facilitate manuf

49、acture is permissible, provided the thread Any additional basting or is removed, or does not show on the finished garment. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - -I_- _ -_I- MIL-T-390LE L1 - 9999906 037q49b O - MIL-T-3901E 3.7.1 Shade and size marking. The cut parts of the trousers shall be marked to Any method of marking may insure a uniform shade and size throughout t

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1