ARMY MIL-T-46748 H-1991 TRUCKS REFUSE COLLECTION WITH FRONT CONTAINER HOIST 20 200 TO 25 400 KILOGRAMS (44 500 T 56 000 POUNDS) GVW 6X4 WITH TILT CAB MODIFIED COMMERCIAL《GVW(总重量)为2.pdf

1、 MIL-T-46748H 23 W 999990b 0495469 T I- NOT MEASUREMENT SENSITIVE MIL-T-46748H - SUPERSEDING MIL-T-46748G 8 December 1989 MILITARY SPECIFICATION * TRUCKS, REFUSE COLLECTION: WITH FRONT CONTAINER HOIST; 20 200 TO 25 400 KILOGMS (44,500 TO 56,000 POUNDS) GVW, 6x4, WITH TILT CAB, MODIFIED COMMERCIAL Th

2、is specification is approved for use by all Departments and Agencies of the Department of Defense. .i- l. SCOPE 1.1 SCODR This specification covers diesel engine driven, 6-wheel, $-wheel drive, tilt cab, commercial, compaction type, refuse collection trucks, equipped with a front loading container h

3、oist. Vehicles procured under this specification are commercial items which are warranted by the manufacturer as specified in acquisition documents, . 1.2 Yehicle classificatiqn The truck shall be one of the following I1 types and classes, as specified (see 6.2 and 6.4): Type II - 20 200 kg (44,500)

4、 GVW - 18.4 cubic metera (m3) (24 cubic Type III - 23 100 kg (51,000) GW - 22.8 ms (30 cubic yards) Type IV - 25 400 (56,000) GVW - 25.9 m3 (34 cubic yards) Class B - 2040 kg (4,500 pound) hoist Class C - 2720 kg (6,000 pound) hoist Class D - 3630 kg (8,000 pound) hoist Class E - 4540 kg (10,000 pou

5、nd) hoist yards) Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: US Army Tank-Automotive Command, AT“: AMSTA-UED, Warren, MI 48397-5000, by using the self-addressed Standardization Document Impr

6、ovement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A IFCC23201 i. i. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-4b74H i13 M 9999906 0495470 b M

7、 MIL-T-46748H 2 APPLICABLE I30CIJMENTS 2.1.1 SpecifiCaAions. standards and hanhxh . The folowing specifications, standards and handbooks form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the De

8、partment of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL A-A-393 - Extinguisher, Fire, Dry-Chemical (Hand- w-E(-131 - Battery, Storage: Vehicular, Ignition, W-F-800 - Fuel Oil, Diesel. Portable). Lighting a

9、nd Starting. MILITARY MIL-T-704 MIL-T-5624 - Turbine Fuel, Aviation, Grades JP-4 and MIL-R-22827 Hoisting Units. MIL-R-23954 - Refuse Containers, Hoisting Unit; Tilt- over, for Front Loading Compaction Type Trucks - - Treatment and Painting of Materiel. JP-5 - - Refuse Containers and Modification Ki

10、ts, MIL-T-83133 - Turbine Fuel, Aviation, Kerosene Type, Grade MIL-H-83282 - Hydraulic Fluid, Fire-Resi-stant , Synthetic JP-R . Hydrocarbon Base, Aircraft, NATO Code Number H-537 - STANDARDS FEDERAL PED-STD-297 - Rustproofing of Commercial (Nontactical) FEU-STD-595 - Colors. Vehic.les. MI LI TARY M

11、IL-STD-1223 - Nontactical Wheeled Vehicles Treatment, Painting, Identification Marking and Data Plate Standards. * (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Naval Publications and Forms Center, Military Specifications

12、and Standards, 131dg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094-) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MInT4bLl8H 23 = 9999906 0495471 8 MIL-T-46748H 2.1.2 Z5 drus. and mritians - The fallawing other Government documents, drawi

13、ngs, and publications form a part of this document to the extent specified herein. the issues shall be those cited in the solicitation. Unless otherwise specified, DEPARTMENT OF DEFENSE Department of Defense Index af Specifications and Standards (DODIEX)- (Copies of the DODISS are available on a yea

14、rly subscription basis either from the Government Printing Office for hard copy, or microfiche copies are available from the Director, Navy Publication and Printing Service Office, 700 Robbins Avenue, Philadelphia, PA 19111-5093.) DEPARTMENT OF TRANSPORTATION (DOT) Federal Motor Carrier Safety Regul

15、ations. Federal Motor Vehicle Safety Standards. i (Application for copies of DOT publications should reference the code of Federal Regulations, 49 CFR, and the Federal Register and should be addressed tu the. superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402.) ENVI

16、RONMENTAL PROTECTION AGENCY (EPA) Control of Air Pollution from New Motor Vehicles and New Motor Vehicle Noise Emission Standards for Transportation Equipment - Medium and Engines. Heavy Trucks. .(Application for copies of EPA publications should reference the Code of Federal Regulations, 40 CFR, an

17、d the Federal Register and should be addressed to the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402.) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION (OSHA) Occupational Safety and Health Standards. (Application for copies of OSHA publications should reference th

18、e Code of Federal Regulations 29 CFR Part 1910 and the Federal Register and should be addressed to the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402.) 2.2 h - Gnverwt mbl- - this document to the extent specified herein. the issues of the documents which are DoD

19、 adopted are those listed in the issue of the DODISS specified in the solicitation. specified, the issues of the documents not liated in the WDISC are the issues of the documents cited in the solicitation (see 6.2). The following documents form a part of Unless otherwise specified, Unless otherwise

20、3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIbnT46748H 23 9 999990b 0495472 T 9 MIL-T-46748H AMERICAN NATIONAL STANDARDS INSTITUTE, INC. (ANSI) ANSI Standards. 2245 - 1-84 - Refuse Collecting and Compacting Equipment - Safety Requirements. (A

21、pplication for copies of ANSI publications should be addressed to the American National Standards Institute, Inc., 1430 Broadway, New York, NY 10018. ) AMERICAN SOCIETY OF MECHANICAL ENGINEERS (ASME) Boiler and Pressure Vessel Code, Section VIII. (Application for copies of ACME publications should b

22、e addressed to the American Society of Mechanical Engineers, United Engineering Center, 345 East 47th Street, New York, NY 10017.) AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM B 117 - Method of Salt Spray (Fog) Testing. * ASTM D 4985 - Standard Specification for Low Silicate Ethylene Glyco

23、l Base Engine Coolant for Heavy Duty Engines Requiring an Initial Charge of Supplemental Coolant Additive. (Application for copies of ASTM publications should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) THE EUROPEAN TIRE AND RIM TECHNICA

24、L ORGANISATION (ETRTO) Standards Manual (Application for copies of the ETRTO publications should be addressed to the European Tyre and Rim Technical Organisation, 32, Avenue Brumm, 1060 Brussels, Belgium.) SAE, INC. SAE Standards and Recommended Practices 5537 - Storage Batteries. 5551 - Performance

25、 Levels and Methods of Measurement of Electromagnetic Radiation from Vehicles and Devices (30-1000 MHz). J588 - Turn Signal Lamps. 5589 - Turn Signal Switch. 5682 5688 - Truck Ability Prediction Procedure (DoD 51349 - Rear Wheel Splash and Stone Throw Protection (DoD adopted). adopted). Diesel - - E

26、ngine Power Test Code - Spark Ignition and 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-46748H (Application for copies of SAE publications should be addressed to SAE, Inc-, 400 Commonwealth Drive, Warrendale, PA 15096.) THE TIRE AND RIM AS

27、SOCIATION, INC. Year Book * be addressed to the Tire and Rim Association, Inc., 175 Montrose West Avenue, Copley OH 44321.) (Application for copies af Tire and Rim Association publications should (Non-Government standards and other publications are normally available from the organizations that prep

28、are or distribute the documents- documents also may be available in or through libraries or other inf ormatlional services. ) These 2.3 Order of mecedea. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing

29、in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Standard vehicle ad accessorieB . Except as specified in 3.1.1 through 3-1.1.6, the vehicle, components, assemblies, and accessories to be delivered under the cont

30、ract shall be standard or optional items, which meet or exceed the requirements of this specification. 3.1.1 through 3.1.1.6, no removal, substitution or alteration of the chassis manufacturers standard or optional chassis model components shall be made. All chassis items shall be as represented in

31、the chassis manufacturers technical data book. represented in the body and equipment manufacturers technical data, Technical data shall be limited to specifications and technical material, identical to that furnished to the authorized company representatives for selection of vehicle models and compo

32、nents, and shall be available to the engineering offices of the procuring activity, prior to delivery of the items. The chassis model furnished shall be not older than the chassis manufacturers current model on the date of invitation for bids. Except as specified in Special bodies or mounted equipme

33、nt shall be as 3.1.1 -cial reaaements . In addition to the standard vehicle and components specified in 3.1, the vehicle shall be furnished with special equipment as specified herein. . Treatment, painting, marking and data 3.1.1.1 andl markine: plates shall be in accordance with MIL-STD-1223. ident

34、ification markings shall be in accordance with MIL-STD-1223 for the military service identified by the procuring activity (see 6.2), except for the following: The exterior color and the 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIkaTv4b74H 23

35、 = 9999906 0495474 3 = MIL-T-46748H (a) The exterior of the complete body unit (see 3.5 through 3-5-71 shall be cleaned in accordance with the manufacturers standard commercial practice and treated and painted in accordance with type A of MIL-T-704; % (b) The interior of the body shall be painted wi

36、th rust inhibiting * primer, grey or beige in color; The color of the exterior of the vehicle shall match color chip No. 13538, gloss yellow, of FED-STD-595 for the Navy; color chip No. 16081, gloss grey, for the Air Force; and color chip No. 17875, gloss white, for all other services; (d) The color

37、 of vehicle identification markings shall be gloss black matching color chip No. 17038 for the Navy; reflective white numerals and letters on a red background for the Air Force; and gloss black matching color chip No. 17038 numerals and letters on a reflective white background on the vehicle and fro

38、nt and rear marker plates for all other services; (c) (e) Rubber seals and hydraulic hoses shall not be painted. 3-1-1.2 -roofin$ - When scified (see G-L), the cab, chassis and complete underside of the refuse collection body including fenders, skirts and wheelwells shall be rustproofed in accordanc

39、e with FEU-STU-297 - When specified (see 6 2) FED-STD-297 shall be furnished. tropical rustproof ing of these areas in accordance with 3.1.1.3 . Drain plugs installed in the rear axle shall be of the permanent magnet; type. 3.1.1 - 4 Towirie. 4. devices . Towing devices consisting of two hooks, loop

40、s, eyes, or pins or the chassis manufacturers standard single center mounted eye or pin shall be momted on the front of the vehicle. All towing devices shall be frame rail mounted or reinforced back to each frame rail. 3.1.1.5 stone throw srotectiola . Rear wheel splash and stone throw protection in

41、 accordance with SAE J682 shall be furnished. Rubber mud flaps or fenders shall be provided to the rear of the front wheels and shall extend down to at least the centerline of the front axle. A metal strip, not less than 3.2 millimeters (mm) (0.125 inch) thick and not less than 25 mm (1 inch) wide,

42、extending the entire width of the mud flap, shall be installed to prevent bolt heads or bolt nuts from damaging the mud flap. alternate method of attaching the mud flaps, tabs or clips with minimum surface contact dimensions of 25 mm (i inch) high by 32 min (1.250 inch) wide by 24 mm (0.094 inch) th

43、ick shall be furnished at each bolt. All tilt cabs shall have rubber mud flaps to the rear of the front wheels. As an 2: 3.1.1.6 k least one pair of brake lights shall override the four-way emergency flasher or the two systems shall be independent of each other. Modifications to the manufacturers st

44、andard product to 6 1 I I I 1 1 *- I I l I I , Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-4b4H 23 M 999990b 0495475 5 Type II III IV MIL-T-46748H Minimum GW kg (pounds) Minimum payload kg (pounds) 20 200 (44,500) 6350 ( 14,000) 23 100 (51,

45、000) 8150 ( 18,000) 25 400 (56,000) 9980 (22,000) accommodate this requirement shall not compromise conformance to any Federal Motor Carrier Safety Regulation referenced herein or to any Federal Motor Vel-iicle Safety Standard. If additional lights are added to the vehicle, the lghta shall te select

46、ed from the chassis or body manufacturers standard matching hardware. 3.2 Genera1 design- 3-2-1 Eadaral Plptnr Vehicle Safetv yr ,t.- - The vehicle and furnished accessories shall comply with all Federal Motor Vehicle Safety Standards in effect on date of manufacture. 3.2.2 Air mllutian cnntzd - The

47、 vehicle shall comply with EPA Regulations governing Control of Air Pollution from New Motor Vehicles and New Motor Vehicle Engines in effect on the date of manufacture. vehicles destined for California shall comply with State of California regulations governing air pollution control in effect on th

48、e date of manufacture- In addition, * 3.2.3 Sound level. The cab interior sound level shall not exceed 84 db(A) when measured in accordance with Federal Motor Carrier Safety Regulation 393.94. container hoisting cycles shall be within the permissible noise exposure levels of Occupational Safety and

49、Health Standard 1910.95, based on an exposure duration of 8 hours per day. conform to the Environmental Protection Agency Noise Emission Standards for Transportation Equipment, Medium and Heavy Trucks. The cab interior noise level during the packing and The vehicle exterior sound level shall 3.2.4 Curb we- . The curb weight shall include the weight of the chassis and cab, with all attachments, accessories, and equipment; the body and hoist; an