ARMY MIL-T-62110 G-1990 TRUCKS MAINTENANCE WITH ROTATING HYDRAULIC DERRICK 32 000 TO 44 500 GVW 4X2 4X4 6X4 AND 6X6 COMMERCIAL《GVW为32 000 至 440 500磅 规格为4X2 4X4 6X4及6X6 装有旋转液压井架的维修车.pdf

1、MIL-T-62LlOG 23 9999906 Oq32787 6 I MILT-6211OG 16 Amil 1990 SUPERSEDING 14 December 1987 MILT-62110F MILITARY SPECIFICATION TRUCKS, MAINTENANCE: WITH ROTATING 4x2, 4x4, 6x4 AND 6x6, COMMERCIAL HYDRAULIC DERRICK, 32,000 TO 44,500 GVW, This specification is approved for use by all Departments and Age

2、ncies of the Department of Defense. 1. SCOPE 1.1 Scow. This specification covers maintenance trucks with a rotating and telescoping hydraulic derrick. specification are commercial items which are warranted by the manufacturer as specified in acquisition documents. Vehicles procured under this - The

3、vehicle shall be one of the types, models, 1.2 classes, and sizes shown in table I, as specified (see 6.2). The model of the vehicle shall be determined by the number of wheels and number of driving wheels- derrick shall be capable of setting. The size of the vehicle shall be the length of the pole

4、that the Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: US Army Tank-Automotive Command, ATTN: AMSTA-UED, Warren, MI 48397-5000, by using the self-addressed Standardization Dociunent Improvemen

5、t Proposal (DD Form 1426) appearing at the end of s dowent nr bv letter. AMSC N/A Jl3xdzd DISTRIBUTION STATWDT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- NIL-T-6211OG 23 W 997990b Oq327

6、f f I MIL-T-62110G e. TABLE I. vehicle classification. Derrick location cabinets, no roof racks above 1.2.1 Class. gross vehicle weight (GVW) rating as specified in table II: The class of a vehicle shall be determined by the minimum t * TABLE II. CVW r-. * 2. APPLICABLE DOCUMENTS . The following * 2

7、.1.1 Siecsications. steda an- specifications, standards and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS), and

8、supplement thereto, cited in the solicitation (see 6.2). * SPECIFICATIONS FEDERAL W-B-131 W-F-800 - Battery, Storage: Vehicular, Ignition, - Fuel Oil, Diesel Lighting and Starting, 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MILITARY MIL-P-514

9、* MIL-T-5624 * MIL-T-83133 MIL-H-83282 STANDARDS FEDERAL FED-STD-297 FED-STD-595 MIL-T-62LLOG 23 777770b 0432787 T I MIL-T-62110G - Plates, Identification, Instruction and - Turbine Fuel, Aviation, Grades JP-4 and - Turbine Fuel, Aviation, Kerosene Type, Grade - Hydraulic Fluid, Fire-Resistant, Synt

10、hetic Marking, Blank. JP-5 - JP-8. Hydrocarbon Base, Aircraft, NATO Code Number H-537. - Rustproofing of Commercial (Nontactical) - 010r8. Vehicles. MILITARY MI L-STD-1223 - Nontactical Wheeled Vehicles Treatment, Painting, Identification Marking and Data Plate Standards. Capacity, Manual Release. M

11、S51118 - Pintle Assembly, Towing - 40,000 Lbs. MS51317 - Light, Warning, Vehicular, Rotating, D.C. * specifications, standards, and handbooks are available from the Naval Publications and Forms Center, Military Specifications and Standards, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.)

12、 (Unless otherwise indicated, copies of federal and military * 2.1.2 OthPLAxudocuments. drwinas. and mb- . The following other Government documents form a part of this specification to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on the date of the sol

13、icitation. * DEPARTMENT OP DEFENSE Department of Defense Index of Specifications and Standards (WDISS). (Copies of the DODISS are available on a yearly subscription basis either form the Government Printing Office for hard copy, or microfiche copies are available from the Director, Navy Publication

14、and Printing Service Office, 700 Robbins Avenue, Philadelphia, PA 19111-5093.) DEPARTMENT OF TRANSPORTATION (DOT) Federal Motor Carrier Safety Regulations. Federal Motor Vehicle Safety Standards. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-

15、T-62110G 23 W 79777Ob 0432790 b I MIL-T-621 iOG (Application for copies of DOT publications should reference the Code of Federal Regulations, 49 CFR, and the Federal Register and should be addressed to the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402.) ENVIRON

16、MENTAL PROTECTION AGENCY (EPA) Control of Air Pollution from New Motor Vehicles and New Motor Vehicle Noise Emission Standards for Transportation Equipment - Medium and Engine8 (. Heavy Trucks. (Application for copies of EPA publications should reference the Code of Federal Regulations, 40 CFR, and

17、the Federal Register and should be addressed to the Superintendent of Documenta, U.S. Government Printing Office, Washington, D.C. 20402.) OCCUPATIONAL SAFETY AND HISALTH ADMINISTRATION (OSHA) Occupational Safety and Health Standards. 1926.556 - Aerial Lifts. (Application for copies of OSHA publicat

18、ions should reference the Code of Federal Regulations, Title 29, and should be addressed to the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402.) * 2.2 2 - . The following documents form a part of this document to the extent specified herein. the issues of the do

19、cuments which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). Unless otherwise specified, Unless otherwise specified, AMERICAN NATIONAL, STANDA

20、RDS INSTITUTE (ANSI) ANSI A92.2 - American National Standard for Vehicle-Mounted Elevating and Rotating Aerial Devices. (Application for copies of ANSI publications should be addressed to the American National Standards Institute, Inc., 1430 Broadway, New York, NY 10018 - ) AMERICAN SOCIETY FOR TEST

21、ING AND MATERIALS (ASTM) ASTM Standards. A120 - Pipe, Steel, Black and Hot-Dipped Zinc-Coated (Galvanized) Welded and Seamless, for Ordinary Uses (DoD adopted). BU7 - Standard Method of Salt Spray (Fog) Testing. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license f

22、rom IHS-,-,- MIL-T-62LLOG 23 779970b 0432773 B I MIL-T-62110G (Application for copies of ASTM publications should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) si: THE EUROPEAN TYRE AND RIM TECHNICAL ORGANISATION (ETRTO) Standards Manual (

23、Application for copies of the ETRTO publications should be addressed to the European Tyre and Rim Technical Organisation, 32, Avenue Brugmann, 1060 Brussels, Belgium.) NATIONAL FIRE PROTECTION ASSOCIATION (NPPA) NFPA-70 - National Electrical Code. * NORTH ATLANTIC TREAIY ORGANIZATION (NATO) Allied E

24、ngineering Publication (AEP-5) Part II - NATO Standard Diesel and Spark Ignition Engines Laboratory Test, dated January 1984. (Application for copies of NATO publications should be addressed to North Atlantic Treaty Organization, Military Agency for Standardization, 1110 Brussels, Belgium.) CAE, INC

25、. 5318 SAE Standards 5350 5537 555 i 5560 5588 5589 5682 5683 5688 5704 and Recommended Practice. - Air Brake Gladhand Service (Control) and Emergency (Supply) Line Couplers - Trucks, Truck-Tractors, and Trailers (DoD adopted). Size Engines (DoD adopted)- - Spark Arreater Test Procedure for Medium -

26、 Storage Batteries. - Performance Levels and Methods of Measure- ment of Electromagnetic Radiation from Vehicles and Devices (30-1000 MHz)- - Seven-Conductor Electrical Connector for Truck-Trailer Jumper Cable. - Turn Signal Lamps. - Turn Signal Switch. - Rear Wheel Splash and Stone Throw Protection

27、 (DoD adopted)- - Tire Chain Clearance - Trucks, Buses, and Combinations of Vehicles- - Truck Ability Prediction Procedure (DoD adopted). - Openings for Six- and Eight-Bolt Truck Trmsmission Mounted Power Take-offs. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without licen

28、se from IHS-,-,-MIL-T-62LLOG 23 7477706 01132772 T W MIL-T-62110G 5706 5844 51067 51292 51349 - Rating of Winches, - Nonmetallic Air Brake System Tubing (DoD - Seven-Conductor Jacketed Cable for - Automobile, Truck, Truck-Tractor, Trailer - Engine Power Test Code - Spark Ignition and adopted). Truck

29、-Trailer Connections. and Motor Coach Wiring. Diesel. (Application for copies of SAE publications should be addressed to CAE, Inc., 400 Commonwealth Drive, Warrendale, PA 15096.) THE TIRE AND RIM ASSOCIATION, INC. Year Book. (Application for copies of Tire and Rim Association publications should be

30、addressed to The Tire and Rim Association, Inc., 3200 W. Market Street, Akron, OH 44313.) 2.3 Sk-recscaence. In the event of a conlict between the text of this document and the references cited herein, the text of this document shall take precedence. Nothing in this document, however, shall supersed

31、e applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS * 3.1 Ctandard vhng . When specified (see 6.2), the vehicle shall be rustproofed in accordance with FED-STD-297. tropical rustproofing in accordance with FED-STD-297 ahdl be furnished. When specified (se

32、e 6.2), Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-62LLOG 23 m 7777906 0432774 3 m MIL-T-62110 3.1.1.4 . Drain plugs installed in the manual transmission, transfer case, and axle(s) for draining lubricants shall be of the permanent magnet

33、type. * 3.1.1.5 Towine: devu . Not less than two hooks, loops, or pins, or a single center mounted towing eye for towing the vehicle, shall be furnished on the front of the vehicle. or reinforced back to each frame rail. All towing devices shall be frame rail mounted * 3.1.1.6 Trailer te wnu - A tra

34、iler towing package consisting of a pintle, safety chain attachment devices, a lighting receptacle, and associated reinforcements and wiring shall be installed on the rear of the vehicle. The pintle shall be installed on the chassis frame with reinforcements to transfer a vertical tongue load of not

35、 less than 4,000 pounds and a horizontal drawbar load of not less than 40,000 pounds directly to the chassis rails. more than four inche8 forward, of the rearmost part of the vehicle. trailer safety chain attachment devices, one adjacent to each side of the pintle, shall be provided. strength at lea

36、st equal to the GVW of the truck furnished. devices shall be capable of accommodating a standard grab hook (4-9/16 inches wide, 1-3/16 inches thick, 25/32 inch throat width) for a 5/8-inch chain. The lighting receptacle, conforming to SAE 5560 with its conductors connected and color-coded or number-

37、coded as specified therein, shall be mounted in a readily accessible location near the pintle. The pintle shall be of the rotating type conforming to MS51118-i. The rearmost portion of the pintle shall be forward, but not Each attachment device shall provide an ultimate Two The attachment 3.1.1.7 Tr

38、ailere cabh . A trailer lighting cable, conforming to Both ends of the cable shall be SAE 51067, shall be furnished. edended length of not less than 110 inches. equipped with a seven-circuit round plug conforming to CAE 5560. shall be equipped with a grip for withrawing from the connector sockets. T

39、he cable shall be packaged and stowed in the vehicle tool compartment. The cable shall be coiled and shall have an The plugs 3.1.1.8 . When specified (see 6.2), the vehicle shall be provided with an electric trailer brake controller. The controller shall be installed in the truck cab and wired throu

40、gh the CAE 5560 lighting receptacle. system of the vehicle and shall include load control, hand lever and accessories. The controller shall operate on the 12-volt electrical 3.1.1.9 or a payload of not less than 2,500 pounds, whichever provides the greater GVW. 3.2.6.1 k except that when equippd wit

41、h interaxle compensating devices, the vehicle shall meet the performance requirements with the front wheel drive engaged. For model 4x4 and model 6x6 vehicles, . The vehicle shall ascend a 1.0 percent * 3.3.1.1 Hi,ii;ers and fiid wamw When specified (see 6.2), a coolant heater, an engine oil heater,

42、 and a fuel warmer (for diesel engine driven vehicles only) shall be provided. Unless otherwise specified (see 6,2), a battery heater shall be provided when power plant heaters are specified. .Heaters shall operate on 110-volt alternating current (ac), and shall be wired through a junction block, in

43、cluding a fuse or circuit breaker? to a single three-pronged (male), weatherproof, slave receptacle for receiving external power and grounding the vehicle. A three-wire connecting cable, 25 feet long and of adequate line capacity to supply power for all heater units simultaneously, shall be furnishe

44、d. The connecting cable shall 14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-62LLOG 23 = 7977706 0432801 7 MIL-T-621lOG include a matching female connector at the vehicle end and a standard, weatherproof, three-pronged (two power plus one g

45、round) male connector at the other end. Safety Regulation 393.77()(7). Electrical insulation of the connecting cable shall withstand normal operating stresses in low ambient air temperatures (down to minus 60oP) without cracking or loss of dielectric capacity. vehicle component operation and without

46、 loose excess wire. stowing the cable shall be provided inside the vehicle cab. furnished as follows: Electrical apparatus shall conform to Federal Motor Carrier All heater lead wires shall be installed without interfering with Provision for Heaters shall be A coolant heater, 1500-watt minimum ratin

47、g, shall be installed in the engine block or lower coolant inlet hose. Engine coolant thermostat with an operating range of 170F to 195OF shall be ins tal led An immersion type engine oil heater, 300-watt minimum rating, with 1700F to 1950F thermostat, shall be installed in the oil pan through any c

48、onvenient opening The battery heater shall have a capacity adequate to maintain the battery electrolyte at a temprature of not leas than IOOF during vehicle exposure in ambient air temperatures as low as minus 60oF, and shall embody a thermostat to limit the temperature of the electrolyte to not mor

49、e than 8OoF When an auxiliary gasoline engine (see 3.15) is provided, a 300-watt immersion type heater with 170oF to 1950F thermostat shall be installed in the oil pan through any convenient opening A fuel warmer or preheater shall be provided on diesel engine driven vehicles to prevent clogging of fuel filters due to wax crystallization in the fuel. coolant to transfer sufficient heat to the diesel fuel to heat it from an inlet temper