ARMY MIL-T-62531-1986 TRUCKS MILITARY UP TO 5 METRIC TON PAYLOAD GENERAL SPECIFICATION FOR《大于5公制吨的有效荷载能力军用车的一般规定》.pdf

1、_ C43-dc3 MIL-T-62531 23 W 7777906 0203878 = a MIL-T-62531(AT) 18 September 1986 MILITARY SPECIFICATION TRUCKS, MILITARY, UP TO 5 METRIC TON PAYLOAD, GENERAL SPECIFICATION FOR This specification is approved for use by US Army Tank-Automotive .Command, Department of the Army, and is available for use

2、 by all Departments and Agencies of the Department of Defense. 1. SCOPE i 1.1 Scope. This specification covers general and special purpose diesel Trucks may have single front and single rear powered truck chassis, trucks, and truck tractors of all sizes up to and including 5 metric ton payload. axle

3、s, or single front and dual rear axles. 1.2 Applicability. The requirements and verification contained in this specification applies to military design and non-development item (NDI) trucks. The vehicles shall be capable of performing ground transport tasks in selected combat support and service mis

4、sions. 1.3 Use. This specification cannot be used without supplemental information. this specification. Blanks not applicable should be marked “/A“. The rational for the requiremenJs in section 3 and the inspections in section 4 are provided in the appendix. The appendix of this specification parall

5、els sections 3 and 4 of the general specification including corresponding numbers and titles. Each requirement and inspection verification is supported by a rationale, guidance, and lessons learned statement. The need for this information is identified by blanks within Beneficial comments (recommend

6、ations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: US Army Tank-Automotive Command, ATTN: AMSTA-GDS, Warren, MI 48397-5000, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at t

7、he end of this document, or by letter. AMSC N/A FSC 2320 DISTRIBUTION STATEMENT A. Approved for, public release; distributin is unlimited. THIS DOCUMENT CONTAINS /o5 PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-This document provides basic

8、and fundamental information characteristics and requirements, personnel concerned with the preparation of specifications. It will provide valuable information and guidance to The overall concept of this document is not necessarily to restrict or limit requirements, but rather to summarize what the G

9、overnment expects in a military truck with respect to the function, material, manufacturing quality and workmanship and the special characteristics of that vehicle, The requirements cited in this document, although not all inclusive, represents those which are selectively provided on existing milita

10、ry vehicles and most likely will be required on vehicle configurations for future procurements. This document is not intended to be referenced in purchase specification requirements. 1.4 Deviation. result in improvement of system performance, reduced life cycle cost or reduced development cost throu

11、gh deviation from this specification or where the requirements of this specification result in compromise in operational capability, shall be brought to the attention of the acquisitioning activity for consideration of change. Any projected design for a given application which will 1.5 Supplemental

12、information required. Appendix D will provide a quick reference to the paragraphs that require supplementary engineering data to complete this specification for the specific vehicle, model, and type required. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 specificat the extent Specification

13、s, standards, and handbooks. The following Sons, standards, and handbooks form a part of this specification to specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) an

14、d supplement thereto, cited in the solicitation, SPECIFICATIONS FEDERAL 0-1-00490 P-c-437 PPP-C-96 PPP-P-704 VV-P-800 - Inhibitor, Corrosion, Liquid Cooling - Cleaning Compound, High Pressure (steam) - Cans, Metal, 28 Gauge and Lighter. - Pails, Metal: (Shipping, Steel, 1 through - Fuel Oil, Diesel.

15、 System. Cleaner. 12 Gallons). 2 * t Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-T-b$531 23 m 999990b 0203880 2 W MILITARY MIL-P-5 14 MIL-L-2104 MIL-A-8421 MIL-A-11755 MIL-R-46164 MIL-L-46167 MIL-C-46168 MIL-E-52798 MIL-E-52835 MIL-T-62314 S

16、TANDARDS MILITARY MIL-STD-105 MIL-STD-193 MIL-STD-209 MIL-STD-210 MIL-STD-461 MIL-STD-462 MIL-STD-642 MIL-STD-810 MIL-STD-1179 MIL-STD-1180 MIL-STD-1472 MIL-STD-1474 MIL-STD-45662 HANDBOOKS MIL-HDBK- 75 9 - Plates Identification, Instruction and - Lubricating Oil, Internal Combustion - Air Transport

17、ability Requirements, General - Antifreeze, Arctic Type. - Rustproofing for Military Vehicles and - Lubricating Oil, Internal Combustion - Coating, Aliphatic Polyurethane, Chemical - Enamel, Alkyd, Camouflage - Enamel, Modified, Alkyd, Camouflage, - Test Equipment (Simplified) for Interior Marking,

18、Blank. Engine, Tactical Service. Specifications for. Trailers. Engine, Arctic. Agent Resistant. Lusterless. Combustion Engines (STE/ICE). - Sampling Procedures and Tables for Inspection by Attributes. - Painting Procedures and Marking for Vehicles Construction Equipment and Material Handling Equipme

19、nt. and Tying Down Military Equipment. - Slinging and Tiedown Provisions for Lifting - Climatic Extremes for Military Equipment. - Electromagnetic Emission and Susceptibility Requirements for the Control of Electromagnetic Interference. - Electromagnetic Interference Characteristics Measurement of.

20、- Identification Marking of Combat and Tactical Transport Vehicles. - Environmental Test Methods and Engineering Guidelines. - Lamps, Reflectors and Associated Signaling Equipment for Military Vehicles. - Safety Standards for Military Ground Vehicles. - Human Engineering Design Criteria for Military

21、 Systems, Equipment and Facilities. - Noise Limits for Army Materiel. - Calibration System Requirements. - Human Factors Engineering Design For Amry Materiel. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2.1.2 Other Government documents, drawing

22、s, and publications. The following other Government documents, drawings, and publications form a part of this specification to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on the date of the solicitation. DEPARTMENT OF TRANSPORTATION (DOT) Federal Moto

23、r Carrier Safety Regulations. Federal Motor Vehicle Safety Standards. (Application for copies should be addressed to the Department of Transportation, Federal Highway Administration, Washington, D.C. 20591,) (Copies of specifications, standards, handbooks, drawings, publications, and other Governmen

24、t documents required by the contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.2 Other publications. The following document(s) form a part of this specification to the extent specified herein.

25、Unless otherwise specified, the issues of the documents which are DoD adopted shall be those listed in the issue of the DODISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS shall be the issue of the nongovernment documents which is curren

26、t on the date of the solicitation. SOCIETY OF AUTOMOTIVE ENGINEERS (SAE) SAE 5198 SAE 58 16 SAE 5903 - Windshield Wiper System - Trucks, Buses, - Engine Test Code - Spark Ignition and - Passenger Car Windshield Wiper Systems. and Multi-Purpose Vehicles. Diesel. (Information as to the availability of

27、 the above standards may be obtained from the Society of Automotive Engineers, 400 Commonwealth Drive, Warrendale, PA 15096.) AMERICAN CONFERENCE OF GOVERNMENTAL INDUSTRIAL HYGENISTS (ACGIH) ACGIH ISBN: - TLVs Threshold Limit Values for Chemical 093712-54-6 Substance in the Work Environment Adapted

28、by ACGIH. (Information as to the availability of the above document may be obtained from ACGIH, 6500 Glenway Avenue, Building D-7, Cincinnati, Ohio 45211.) (Nongovernment standards and other publications are normally available from the organizations which prepare or which distribute the documents. T

29、hese documents also may be available in or through libraries or other informational services.) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2.3 Order of precedence. In the event of a conflict between the text of this specification and the refere

30、nces cited herein (except for associated detail specifications, specification sheets or MS standards), the text of this specification shall take precedence. Nothing in this specification, however,-shall supersede applicable laws and regulations unless a specific exemption has been obtained. 2.3.1 Sa

31、fety precedence. Nothing in this specification shall supercede the requirements of MIL-STD-1180 unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. Unless otherwise specified (see 6.2), the contractor shall furnish which shall be subjected to first article inspection (s

32、ee 4.1.7). First article inspection vehicle, properly marked with identifying information shall be representative of the unit to be furnished to the Government. Government shall conform to these samples in all of their pertinent physical and performance attributes. All subsequent vehicle(s) delivere

33、d to the 3.2 Materials. Materials shall be as specified herein and in referenced specifications, standards and drawings. Material shall be free of defects which affect performance or serviceability of the finished product (see 4.3). 3.3 Qualified products. The contractor shall be responsible for usi

34、ng parts and assemblies from Qualified Products List (QPLs) whenever applicable. Contractors inspection records shall specifically list all QPL items by number and date of the QPL, name of supplier and part or drawing number(s). When parts and assemblies are approved as qualified products, but not y

35、et listed on the QPL, the contractor shall list the products by number and date of the approved document and name of supplier(s) (see 4.3).- 3.4 Kits. 3.4.1 Special kits. Provisions shall be made for installation of special kits including winterization equipment. special kits shall be furnished as e

36、quipment. shall fit properly without interference or misalignment and meet applicable environmental and performance requirements specified herein. When specified (see 6-21, Special kits, when installed, 3.4.1.1 Arctic kit. Arctic kits 3.4.1.1.1 through 3.4.1.1.7 shall assure engine starting, operati

37、onal performance-, and provide protection for personnel in ambient temperatures from a minus 32C measured 1.2 to 1.8 meters above ground, to a minus 54“C, measured at ground level. 3.4.1.1.1 Engine coolant heater kit. The engine coolant heater kit furnished shall be in accordance wth drawing . When

38、installed, the engine coolant heater kit shall assure engine starting and operation in ambient temperatures fromminus 32C to minus 54C. 3.4.1.1.2 Radiator and hood cover kit. The radiator and hood cover kit furnished shall be in accordance with drawing . This kit shall be used in conjunction with th

39、e engine coolant heater kit. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.4.1.1.3 Personnel heater kit. The personnel heater kit furnished shall be in accordance with drawing When installed, the personnel heater kit shall supplement the cab pe

40、rsonnel heater and windshield defrosting during ambient temperatures from minus 32OC to minus 54C. dressed in arctic clothing. The heater shall provide a comfortable temperature for personnel 3.4.1.1,4 Soft top kit. The insulated soft top kit furnished shall be in accordance with drawing . When inst

41、alled in accordance with applicable drawings, the insulated top shall provide maximum protection for personnel when the vehicle is operating in adverse climatic conditions. 3.4.1.1.5 Insulated cargo area cover kit. The cargo body kit furnished shall be in accordance with drawing . When installed, th

42、e cargo area cover kit shall completely enclose the cargo area to provide maximum protection for personnel and cargo when operating-in adverse conditions. 3.4.1.1.6 Cargo area personnel heater kit. The cargo area personnel heater kit shall be in accordance with drawing . When installed, the cargo ar

43、ea personnel heater kit shall provide sufficient heat for personnel comfort (when dressed in arctic clothing) and materiel protection (i.e. perishable food) when operating in ambient tempertures to minus 54“C, 3.4.1.1.7 Hard top kit, The hard top kit furnished shall be in accordance with drawing . T

44、he hard top insulation shall afford protection from ambient air temperatures to minus 54OC for personnel dressed in arctic clothing. 3.4.1.2 Deep water fording kit, The deep water fording kit furnished shall be in accordance with drawing . When installed, the kit shall permit the vehicles to be oper

45、ated in water (salt or fresh) to the depth specified in 3.7.3.1 without damage to the vehicle. 3.4.1,3 A-frame kit. The A-frame kit furnished shall be in accordance with drawing , The kit includes an A-frame or derrick mounted at the front of the vehicle for use as a general utility lifting device,

46、and as a derrick in conjunction with the vehicle winch. 3.4.1.4 Vehicle rear lifting kit. The vehicle rear lifting kit furnished shall be in accordance with drawing . When installed, the rear lifting kit shall be capable of loading material weighing UP to kg into the cargo area. 3.4.1.5 Vehicle fron

47、t lifting kit. The vehicle front lifting kit furnished shall be in accordance with drawing , When installed, the front lifting kit shall be capable of lifting material weighing up to kilogram (kg). 3.4,1,6 Bow and tarp kit (long cargo body). The bow and tarp kit (long cargo body) furnished shall be

48、in accordance with drawing . 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.4.1.7 Bow and tarp kit (drop side cargo body). The bow and tarp kit (drop side cargo body) furnished shall be in accordance with drawing 3.4.1.8 Bow and tarp kit (short

49、cargo body). The bow and tarp kit (short cargo body) furnished shall be in accordance with drawing . 3.4.1.9 Tarpaulin extension kit. The tarpaulin extension kit furnished shall be in accordance with drawing . 3.4.1.10 Gun-ring mounting kit. The gun-ring mounting kit conforming to degree rotation of the drawing , when installed, shall permit a - machine gun without interference or binding. 3.4.1.11 Automotive alarm kit. The automotive alarm kit furnished shall