ARMY MS51835 REV A-1970 INSERTS AND STUDS LOCKED IN - KEY LOCKED HOLE DIMENSIONS FOR AND ASSEMBLY OF《上锁禁闭嵌件和螺栓的孔眼尺寸和组装》.pdf

1、US53835 REV A 53 U 7777732 000b233 b U D or T FIGURE I -CONFIGURATION FOR TABLES I, II AND 111 NOTES 1. 2. 3. 4. 5. 6. 7. 8. INSERTS AND STUDS, LOCKED IN - KEY LOCKED, HOLE DIMENSIONS FOR AND ASSEMBLY OF AXIS OF HOLE TO BE NORMAL TO ENTRY SURFACE OR PROVIDE SPOTFACE WHEN REQUIRED. UNIFIED NATIONAL C

2、LASS 28 OR 38 THREADS. SURFACE ROUGHNESS: UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES IN ACCORDANCE WITH NfSI B46.1 NOMINAL USE: FOR INSTALLATION OF KEY-LOCKED INSERTS AND STUDS CONFORMING TO MS51830, MS51831, MS51832, MS51833, AND MS51834, AS APPLICABLE. MS51835, FIGURE II.

3、INSTALLATION: PROCEDURE AND INSTALLATION OF KEY-LOCKED INSERTS AND STUDS, SEE REMOVE ALL BURRS AND SHARP EDGES. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES, LINEAR DIMENSIONS i .O05 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-r -

4、 .A. WC TITLE bGdClll As INSERTS AND STUDS, LOCKED IN - MILITARY STANDARD 82 KEY LOCKED, HOLE DIMENSIONS FOR AND ASSEMBLY OF IMS 51835 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FED. SUP CLASS TABLE 111 - INSTALLATION HOLE DlMENSlONS FOR MS 5183

5、2 53GP NOMINAL THREAD SIZE NUMBER FOR INSERT (REF) I l .4375-14 -101 -201 .401 .396 CSlNK DIAMETER +.o10 NATIONAL THREAD UNIFIED CLASS 28 MIN FULL THREAD I I .447 .4375-14UNC .370 .625-1 l -104 383 -204 ,577 -105 -205 .&6 .&O .635 .625-llUNC .560 ,6875-11 .7w .6875-1 INS .680 .8125-16 -106 .771 -206

6、 .765 -107 -207 333 .827 322 .8125-16UN .750 ,875-14 .885 .875-14UNC .940 I 1.250-12 I :109(L) I I 1.270 I 1.250-12UNF I (L) .440 1.310 209(L) 1.186 I I 1.375-12 I I I 1.395 I 1.375-12UNF I (L) .5M) -210(L) 1.311 T- l i I , I j , I c l 4 I ,A. WC TITLE MILITARY STANDARD Lw Cul AS INSERTS AND STUDS,

7、LOCKED IN - 82 KEY LOCKED, HOLE DIMENSIONS FOR AND ASSEMBLY OF MS 5 I 8 3 5 $OCUREWNT SPECIFICATIO( SUPERSEDES SHEET OF 2 - I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I IMPORTANT DO NOT SPECIFY STUD PROJECTION r SEE NOTE 1 AND 2 M551832 FIGURE

8、 II -ASSEMBLY OF INSERTS AND STUDS HOLE PREPARATION IN ACCORDANCE WITH TABLES I, II AND 111 PER APPLICABLE EXTERNAL THREAD SIZE OF PART AND CORRESPONDING DASH NUMPR. 1. INSTALL INSERT OR STUD AS SHOWN. (KEYS LOCATE CORRECT DEPTH.) 2. DRIVE KEYS AS SHOWN. 3. TYPICAL DRAWING CALLOUT TO E LOCATED IN VI

9、CINITY OF PART IDENTIFICATDN. FOR INSERT FOR STUD INSTML INSERT IN ACCORDANCE INSTAU STUD IN ACCORDANCE WITH MS51835 WITH M51835 i INSERT VKW I STUD VIEW 4. REPLACEMENT OF INSERTS AND STUDS IS MADE WITH SAME SIZE PARTS AS THOSE REMOVED AND IN SAME MANNER AS ORIGINALLY INSTALLED, 5. IN MATERIALS HARD

10、ER THAN 150 BRINNELL, KEY SLOTS, BROACHED PRIOR TO INSERT INSTALLATION, MAY L REQUIRED. 6. ILLUSTRATION IS FOR IDKfilWEATIMI AM) IS m)T IhiED TO RESTRICT DESIONS AND SWEB Op IXSHITS AM) SNE WKICH OIXEWISE COHFOAM To “B. THIS IS A DESIGN STANDARD AND SHALL NOT BE USED AS A PART NUMER .L WC TITLE kcd As INSERTS AND STUDS, LOCKED IN - MILITARY STAWDARI 82 KEY LOCKED, HOLE DIMENSIONS FOR AND ASSEMBLY OF MS 5 I 8 3 fs Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-