ARMY PPP-T-680 E-1975 TAPE PRESSURE-SENSITIVE ADHESIVE PACKAGING AND PACKING OF [Use In Lieu Of ARMY PPP-T-00680 B (1)]《压敏胶带的封装与包装[代替 ARMY PPP-T-00680 B(1)]》.pdf

1、I PPP-T-68IJE PA M 7774774 0055480 L PPP“F680E NOVSbW 17, 1975 -m Fed. Spec. PPJ?“F680D April 16 I 1971 . . . - FEDERAL SPECIFICATION TAPE, PRESSURE-SENSITIVE ADHESIVE: PACKAGING AND PACKING OF This specification was approved by the Commissioner, Federal Supply service, General Services Administrati

2、on, for the use of all Federal agencies. 1.1 This specification covers the requirements for the packaging, packing, and marking of pressure-sensitive adhesive tapes, except electrical and foam . type tapes. 2. APPLICABLE DOCUMENTS 2.1 The following documents, of the issue in effect on date of invita

3、tion for bids or request for proposal, form a part of this specification to the extent specified herein: Federal Specifications: UU-P-134 - Paper, Wrapping, Wet-Waxed UU-P-268 - Paper, Kraft, Wrapping uu-P-270 - Paper, Wrapping, Waxed (Dry) PPP-B-566 - Boxes, Folding, Paperboard PPP-B-63 6 - Boxes,

4、Shipping, Fiberboard PPP-B-676 - Boxes, Setup Federal Standard FED-STD-123 - Marking for skiprvant (civil Agencies) . (Activities outside the Federal Government may obtain copies of Federal Specifications, Standards, and Handbooks as outlined under General Information in the Index of Federal Specifi

5、cations and Standards and at the prices -indicated in the Index. The Index, which includes cumulative monthly supplements as issued, is for sale on a subscription basis by the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402. FSC PACK - Licensed by Information Handl

6、ing ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-PPP-T-hdOE PA M 7777774 0055481 3 r PPP-T-680E (single copies of this SpeCificWd and othq F- specifications required by activities outside tlie Fkderal and the wrapper heat sealed. Alternati

7、vely, a laminate of aluminum foil to paperr laminated with wax or polyethylene, may be used in lieu of the material complying with MIL-B-131. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-PP-T-680E 3.1.1.2 Single and double coated cloth and paper

8、 tape. Each roll of tape shall be packaged in a paperboard box conforming to variety 2, classification optional of PPP-By566 or variety 2, classification optionl Individual roll. Each roll of tape, not: more than 3 inches wide, and not mote than 72 yards long, shall be individually packaged in accor

9、dance with the requirements Qf 3.1b2 ,1,1 through 3.1.2.1.3 88 applicable. Alternatively, rolls of tape narrower than 314 inch my be packaged in quantities as specified (see 6.1) with a waxed paper separator conforming to UU-P-270 or UU-P-134, or othermaterial haviqg at least equal non-blocking-prop

10、erties, placed between the rolls, -“. 3.1.2.1.1 Cellophane tape. Cellophane tape shall be packaged as specified in 3.1.1.1. 3.1.2.1.2 Single and double coated cloth and paper tape. The tape shall be packaged in a paperbwrd box conforming to variety 1, classification optional of PPP-B-566 or variety

11、1, classification optional of PPP-B-676. A centering device shall be providedrin ea$widths, and Packing Not packed in quantities as specified Not the kind of shipping container specified Centering device missing, a applicable Markings not as specified 4.2.2.2 Examination of shipping containers. When

12、 shipping containers are required to be in accordance with PPP-B-636, examination for defects in closure, waterproofing, and reinforcing shall be in accordance with the appendix of PPP-B-636. When consolidstion boxes are required, examination for defects in assembly, closure, and reinforcing shall b

13、e in accordance with the appendix of MIL-B-43666. 4.2.2.3 Examination for palletization. An examination shall be made to determine that palletization complies with 3.3 requirements. Defects shall be scored in accordance with table IV. The sample unit for this examination shall be one palletized unit

14、 load fully prepared for delivery. The lot shall be the number of palletized unit loads in the end item inspection lot. The inspection level shall be S-1 with an AQL of 6-5 expressed in tema of defects per hundred units. TABLE IV. Examination for palletization Examinat ion Defect Finished dimension

15、Length, width, or height exceeds specified dmm requirement Palletization Not 88 speclfied Pallet pattern not as specified Interlocking of loads not m specified Load not bonded with required straps specified Weight Exceeds maximum load limits Marking Omitted; incorrect; illegible; of improper size, l

16、ocation, sequence or method of application Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Q - PPP-T-b8OE PA = 7777774 0055484 7 PPP-T-680E B 5. PREPARATION FOR DELIVERY 5.1 Not applicable. 6. NOTES . “ 6.1 Ordering deta. Purchasers should select the

17、 preferred options permitted herein and include the following information in procureusnt documents: Title, number, and date of this specification. Selection of the applicable levels of packaging and packing When a quantity of rolls narrower than 3/4 inch are desired to be When water vaporproof prote

18、ction is required for single and double Whether tape shall be individual roll package or multiple roll When consolidation boxes are required for level A packing (see 3.2.1.1). When weather-resistant grade fiberboard shipping containers are When palletization is required by the military (see 3.3). (s

19、ee 3.1 and 3.2). packaged together (see 3.1.1 and 3.1.2.1). coated cloth and paper tapes (see 3.1.1.2). package (see 3.1.2). required for level B packing (see 3.2.2.1.1) . . 6.2 Storage. The tape should be stored in the original container in a cool location. It should not be stored in close proximit

20、y to steam pipes, radiators, or other sources of heat. Temperature of approximately 70 F with 40 to 50 percent relative humidity is most desirable. 6.3 Utility style rolls. A utility style roll shall, forthe purpose of this specification, be defined as a roll of tape on a one inch core, not more tha

21、n- one inch in width, complete with its own integral dispenser. Custodians : Preparing activity : Army - GL Navy - SA Air Force - 84 Review activities : Army -MI, SM Navy - AS Air Force - 69 User activities: Am - MIT, AT Navy - OS, MC, SH Amy - GL Civil Agency Coordinating Activities: GSA-FSS AGR-AP

22、S Project No. PACK-O380 U. S. GOVERNMENT PRINTING OFFICE : 1975 - 210-814/1051 Orders for this- publication are to be placed with General Services Administration, acting as an agent for the Superintendent of Documents See section 2 of this specification to obtain extra copies. and other documents referenced herein. 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-