ARMY UFGS-06 41 16 00 10-2010 LAMINATE CLAD ARCHITECTURAL CASEWORK.pdf

1、*USACE / NAVFAC / AFCESA / NASA UFGS-06 41 16.00 10 (August 2010)-Preparing Activity: USACE SupersedingUFGS-06 41 16.00 10 (August 2009)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated July 2010*SECTION TABLE OF CONTENTSDIVISION 06 - WOOD, PLASTICS, AND COMPOSITESSE

2、CTION 06 41 16.00 10LAMINATE CLAD ARCHITECTURAL CASEWORK08/10PART 1 GENERAL1.1 REFERENCES1.2 SYSTEM DESCRIPTION1.3 SUBMITTALS1.4 QUALITY ASSURANCE1.4.1 General Requirements1.4.2 Mock-ups1.4.3 Sustainable Design Certification1.5 DELIVERY, STORAGE, AND HANDLING1.6 SEQUENCING AND SCHEDULINGPART 2 PRODU

3、CTS2.1 WOOD MATERIALS2.1.1 Lumber2.1.2 Panel Products2.1.2.1 Plywood2.1.2.2 Particleboard2.1.2.3 Medium Density Fiberboard2.2 SOLID POLYMER MATERIAL2.3 HIGH PRESSURE DECORATIVE LAMINATE (HPDL)2.3.1 Horizontal General Purpose Standard (HGS) Grade2.3.2 Vertical General Purpose Standard (VGS) Grade2.3.

4、3 Horizontal General Purpose Postformable (HGP) Grade2.3.4 Vertical General Purpose Postformable (VGP) Grade2.3.5 Horizontal General Purpose Fire Rated (HGF) Grade2.3.6 Vertical General Purpose Fire Rated (VGF) Grade2.3.7 Cabinet Liner Standard (CLS) Grade2.3.8 Backing Sheet (BK) Grade2.4 THERMOSET

5、DECORATIVE OVERLAYS (MELAMINE)2.5 EDGE BANDING2.6 VINYL COUNTERTOP EDGE2.7 CABINET HARDWARE2.8 FASTENERS2.9 ADHESIVES, CAULKS, AND SEALANTSSECTION 06 41 16.00 10 Page 1Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2.9.1 Adhesives2.9.1.1 Wood Joiner

6、y2.9.1.2 Laminate Adhesive2.9.2 Caulk2.9.3 Sealant2.10 WOOD FINISHES2.11 ACCESSORIES2.11.1 Glass and Glazing2.11.2 Grommets2.12 FABRICATION2.12.1 Base and Wall Cabinet Case Body2.12.1.1 Cabinet Components2.12.1.2 Joinery Method for Case Body Members2.12.2 Cabinet Floor Base2.12.3 Cabinet Door and Dr

7、awer Fronts2.12.4 Drawer Assembly2.12.4.1 Drawer Components2.12.4.2 Drawer Assembly Joinery Method2.12.5 Shelving2.12.5.1 General Requirements2.12.5.2 Shelf Support System2.12.6 Laminate Clad Countertops2.12.6.1 Edge Style2.12.6.2 Laminate Clad Splashes2.12.7 Laminate Application2.12.8 Finishing2.12

8、.8.1 Filling2.12.8.2 Sanding2.12.8.3 CoatingsPART 3 EXECUTION3.1 INSTALLATION3.1.1 Anchoring Systems3.1.1.1 Floor3.1.1.2 Wall3.1.2 Countertops3.1.3 Hardware3.1.4 Doors, Drawers and Removable Panels3.1.5 Plumbing Fixtures3.1.6 Glass- End of Section Table of Contents -SECTION 06 41 16.00 10 Page 2Prov

9、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-*USACE / NAVFAC / AFCESA / NASA UFGS-06 41 16.00 10 (August 2010)-Preparing Activity: USACE SupersedingUFGS-06 41 16.00 10 (August 2009)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement wit

10、h UMRL dated July 2010*SECTION 06 41 16.00 10LAMINATE CLAD ARCHITECTURAL CASEWORK08/10*NOTE: This guide specification covers the requirements for laminate clad architectural casework.Edit this guide specification for project specific requirements by adding, deleting, or revising text. For bracketed

11、items, choose applicable items(s) or insert appropriate information.Remove information and requirements not required in respective project, whether or not brackets are present.Comments and suggestions on this guide specification are welcome and should be directed to the technical proponent of the sp

12、ecification. A listing of technical proponents, including their organization designation and telephone number, is on the Internet.Recommended changes to a UFGS should be submitted as a Criteria Change Request (CCR).*PART 1 GENERAL*NOTE: Designer should require materials, products, and innovative con

13、struction methods and techniques which are environmentally sensitive, take advantage of recycling and conserve natural resources.Executive Order No. 12873, dated 20 October 1993, requires that Federal Agencies use environmentally preferable products and services and implement cost-effective procurem

14、ent preference programs favoring purchase of these products and services. “Environmentally preferable“ products and services are those that have a lesser or reduced effect on human health and the environment when compared with competing products or services that serve the same purpose. This comparis

15、on may consider raw SECTION 06 41 16.00 10 Page 3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-materials, components, acquisition, production, manufacturing, packaging, distribution, reuse, operation, maintenance, or disposal of the product or serv

16、ice.Factors to consider include, but are not limited to:1) Ease of repairability and high durability. A lesser frequency of replacement reduces landfill (i.e., need for more natural resources and energy) costs.2) Manufacturer/fabricator programs in place that reduce energy required or re-cycle energ

17、y, water, by-products, or waste materials in production methods.3) Low VOCs and off-gassing in the production, fabrication, assembly, and installation of materials and components.Evaluation of the sustainable efforts of a manufacturer is subjective. There are no current measurable aspects of a susta

18、inable program for casework materials which easily qualifies or disqualifies a manufacturer or fabricator. The submittal reviewer should use the information provided in the Department of Army ETL 1110-3-491 in conjunction with a common sense approach in making the evaluation.*1.1 REFERENCES*NOTE: Th

19、is paragraph is used to list the publications cited in the text of the guide specification. The publications are referred to in the text by basic designation only and listed in this paragraph by organization, designation, date, and title.Use the Reference Wizards Check Reference feature when you add

20、 a RID outside of the Sections Reference Article to automatically place the reference in the Reference Article. Also use the Reference Wizards Check Reference feature to update the issue dates.References not used in the text will automatically be deleted from this section of the project specificatio

21、n when you choose to reconcile references in the publish print process.*The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text by the basic designation only.SECTION 06 41 16.00 10 Page 4Provided by IHSNot for ResaleN

22、o reproduction or networking permitted without license from IHS-,-,-AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI)ANSI A161.2 (1998) Decorative Laminate Countertops, Performance Standards for Fabricated High PressureARCHITECTURAL WOODWORK INSTITUTE (AWI)AWI Qual Stds (8th Edition) AWI Quality Standard

23、sASTM INTERNATIONAL (ASTM)ASTM D 1037 (2006a) Evaluating Properties of Wood-Base Fiber and Particle Panel MaterialsASTM E 84 (2010) Standard Test Method for Surface Burning Characteristics of Building MaterialsASTM F 547 (2006) Nails for Use with Wood and Wood-Base MaterialsBUILDERS HARDWARE MANUFAC

24、TURERS ASSOCIATION (BHMA)ANSI/BHMA A156.9 (2003) Cabinet HardwareCOMPOSITE PANEL ASSOCIATION (CPA)CPA A208.1 (2009) Medium Density Fiberboard (MDF) For Interior ApplicationsCPA A208.2 (2009) Medium Density Fiberboard (MDF) for Interior ApplicationsGREENGUARD ENVIRONMENTAL INSTITUTE (GEI)GEI Greengua

25、rd Standards for Low Emitting ProductsNATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION (NEMA)ANSI/NEMA LD 3 (2005) Standard for High-Pressure Decorative LaminatesSCIENTIFIC CERTIFICATION SYSTEMS (SCS)SCS Scientific Certification Systems (SCS)Indoor AdvantageWINDOW AND DOOR MANUFACTURERS ASSOCIATION (WD

26、MA)WDMA I.S. 1-A (1997) Architectural Wood Flush Doors1.2 SYSTEM DESCRIPTION*NOTE: The term “laminate clad architectural casework“ as used herein includes all wood assembly components and specially designed and fabricated SECTION 06 41 16.00 10 Page 5Provided by IHSNot for ResaleNo reproduction or n

27、etworking permitted without license from IHS-,-,-custom casework that requires a high pressure decorative laminate finish. This should include such items as restroom vanities, cabinets, and built-in shelving as detailed and located on the drawings. Items such as running trim, moldings, wood railings

28、,and other wood decorative components should be specified in Section 06 20 00 FINISH CARPENTRY. Prefabricated, modular casework and cabinetry should be specified in Section 12 32 00 MANUFACTURED WOOD CASEWORK.Solid polymer (solid surfacing) components of laminate architectural casework, such as coun

29、tertops, will be constructed in accordance with Section 06 61 16 SOLID POLYMER (SOLID SURFACING) FABRICATIONS.*Work in this section includes laminate clad custom casework cabinets vanities _ as shown on the drawings and as described in this specification. This Section includes high-pressure laminate

30、 surfacing and cabinet hardware. Comply with EPA requirements in accordance with Section 01 62 35 RECYCLED / RECOVERED MATERIALS. All exposed and semi-exposed surfaces, whose finish is not otherwise noted on the drawings or finish schedule, shall be sanded smooth and shall receive a clear finish of

31、polyurethane. Wood finish may be shop finished or field applied in accordance with Section 09 90 00 PAINTS AND COATINGS.1.3 SUBMITTALS*NOTE: Review submittal description (SD) definitions in Section 01 33 00 SUBMITTAL PROCEDURES and edit the following list to reflect only the submittals required for

32、the project. Submittals should be kept to the minimum required for adequate quality control.A “G” following a submittal item indicates that the submittal requires Government approval. Some submittals are already marked with a “G”. Only delete an existing “G” if the submittal item is not complex and

33、can be reviewed through the Contractors Quality Control system. Only add a “G” if the submittal is sufficiently important or complex in context of the project.For submittals requiring Government approval on Army projects, a code of up to three characters within the submittal tags may be used followi

34、ng the “G“ designation to indicate the approving authority. Codes for Army projects using the Resident Management System (RMS) are: “AE“ for Architect-Engineer; “DO“ for District Office (Engineering Division or other organization in the District Office); “AO“ for Area Office; “RO“ for Resident Offic

35、e; and “PO“ for Project Office. Codes following the “G“ typically are not used for Navy, Air Force, and NASA projects.SECTION 06 41 16.00 10 Page 6Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Choose the first bracketed item for Navy, Air Force and

36、 NASA projects, or choose the second bracketed item for Army projects.*Government approval is required for submittals with a “G“ designation; submittals not having a “G“ designation are for Contractor Quality Control approval. information only. When used, a designation following the “G“ designation

37、identifies the office that will review the submittal for the Government. Submit the following in accordance with Section 01 33 00 SUBMITTAL PROCEDURES:SD-02 Shop DrawingsShop DrawingsInstallationSD-03 Product DataWood MaterialsWood FinishesFinish ScheduleCertificationSD-04 SamplesPlastic LaminatesCa

38、binet HardwareSD-07 CertificatesQuality AssuranceLaminate Clad Casework1.4 QUALITY ASSURANCE*NOTE: This specification relies heavily on standards developed by the Architectural Woodwork Institute (AWI), a national not-for-profit organization of manufacturers of architectural woodwork, suppliers to t

39、he industry, and design professionals to provide specifications which accurately describe and quantify minimum standards for architectural woodwork.AWI architectural woodwork quality standards for casework materials and fabrication lists three quality categories: premium, custom, and economy grade.

40、The specifier must judge the level of quality required for the specific end use conditions. The specifier should become familiar with the differences between custom and premium grade quality differences before editing this specification.To insure suitable durability and appearance it is recommended

41、that either the custom or premium grade quality be selected. Economy grade should only be SECTION 06 41 16.00 10 Page 7Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-considered where severe funding limitations dictate this lesser quality be specifie

42、d. AWI Sections 400G and 400B indicate the differences between grades regarding acceptable materials for substrates and components, fabrication methods, joinery, tolerances, and other factors.*1.4.1 General RequirementsUnless otherwise noted on the drawings, all materials, construction methods, and

43、fabrication shall conform to and comply with the premium custom grade quality standards as outlined in AWI Qual Stds, Section 400G and Section 400B for laminate clad cabinets. These standards shall apply in lieu of omissions or specific requirements in this specification. Contractors and their perso

44、nnel engaged in the work shall be able to demonstrate successful experience with work of comparable extent, complexity and quality to that shown and specified. Submit a quality control statement which illustrates compliance with and understanding of AWI Qual Stds requirements, in general, and the specific AWI Qual Stds requirements provided in this specification. The quality control statement shall also certify a minimum of ten years Contractors experience in laminate clad casework fabrication and construction. The quality control