ARMY UFGS-10 10 00-2009 VISUAL COMMUNICATIONS SPECIALTIES《可视化通讯特殊设备》.pdf

1、*USACE / NAVFAC / AFCESA / NASA UFGS-10 10 00 (February 2009)-Preparing Activity: USACE SupersedingUFGS-10 10 00 (April 2006)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated October 2008*SECTION TABLE OF CONTENTSDIVISION 10 - SPECIALTIESSECTION 10 10 00VISUAL COMMUN

2、ICATIONS SPECIALTIES02/09PART 1 GENERAL1.1 REFERENCES1.2 SYSTEM DESCRIPTION1.3 SUBMITTALS1.4 DELIVERY, STORAGE, AND HANDLING1.5 WARRANTYPART 2 PRODUCTS2.1 MATERIALS2.1.1 Porcelain Enamel2.1.2 Cork2.1.2.1 Colored Cork2.1.2.2 Natural Cork2.1.3 Woven Fabric2.1.4 Non-Woven Fabric2.1.5 Vinyl Wall Coverin

3、g2.1.6 Aluminum2.1.7 Hardwood2.1.8 Glass2.2 PRESENTATION BOARD2.3 MARKERBOARD2.4 TACKBOARDS2.4.1 Cork2.4.2 Vinyl Covered2.4.3 Fabric Covered2.5 CASE FOR BOARD UNIT2.6 DISPLAY TRACK SYSTEM2.7 HORIZONTAL SLIDING UNITS2.8 COPYBOARD2.9 PROJECTION SCREEN2.10 COLORPART 3 EXECUTIONSECTION 10 10 00 Page 1Pr

4、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.1 PLACEMENT SCHEDULE3.2 INSTALLATION3.3 CLEANING- End of Section Table of Contents -SECTION 10 10 00 Page 2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,

5、-,-*USACE / NAVFAC / AFCESA / NASA UFGS-10 10 00 (February 2009)-Preparing Activity: USACE SupersedingUFGS-10 10 00 (April 2006)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated October 2008*SECTION 10 10 00VISUAL COMMUNICATIONS SPECIALTIES02/09*NOTE: This guide spec

6、ification covers the requirements for visual communications specialties.Edit this guide specification for project specific requirements by adding, deleting, or revising text. For bracketed items, choose applicable items(s) or insert appropriate information.Remove information and requirements not req

7、uired in respective project, whether or not brackets are present.Comments and suggestions on this guide specification are welcome and should be directed to the technical proponent of the specification. A listing of technical proponents, including their organization designation and telephone number,

8、is on the Internet.Recommended changes to a UFGS should be submitted as a Criteria Change Request (CCR).*PART 1 GENERAL1.1 REFERENCES*NOTE: This paragraph is used to list the publications cited in the text of the guide specification. The publications are referred to in the text by basic designation

9、only and listed in this paragraph by organization, designation, date, and title.Use the Reference Wizards Check Reference feature when you add a RID outside of the Sections Reference Article to automatically place the reference in the Reference Article. Also use the Reference Wizards Check Reference

10、 feature to update the issue dates.SECTION 10 10 00 Page 3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-References not used in the text will automatically be deleted from this section of the project specification when you choose to reconcile refere

11、nces in the publish print process.*The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text by the basic designation only.AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI)ANSI Z97.1 (2004) Safety Glazing Materials Used in B

12、uildingsASTM INTERNATIONAL (ASTM)ASTM B 221 (2008) Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and TubesASTM B 221M (2007) Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes (Metric)ASTM C 1048 (2004)

13、Standard Specification for Heat-Treated Flat Glass - Kind HS, Kind FT Coated and Uncoated GlassASTM E 84 (2008a) Standard Test Method for Surface Burning Characteristics of Building MaterialsASTM F 148 (2002; r 2007) Binder Durability of Cork Composition Gasket MaterialsASTM F 152 (1995; R 2002) Ten

14、sion Testing of Nonmetallic Gasket MaterialsASTM F 793 (2007) Wallcovering by Durability Characteristics1.2 SYSTEM DESCRIPTION*NOTE: The designer has the option to require that visual display boards for a project be provided by one manufacturer when appropriate. It is the designers responsibility to

15、 determine if all products being specified for a project are available from a minimum of three manufacturers. Not all manufacturers produce the variety of visual display boards offered in this specification.Alternate frame methods such as: self-edge for fabric or vinyl covered tackboards, vinyl edge

16、 on tackboards, and markerboards are options but are not available from all manufacturers. Designer must SECTION 10 10 00 Page 4Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-research available sources.*The term visual display board when used herein

17、 includes presentation boards, marker boards, tackboards, board cases, display track system and horizontal sliding units. Visual display boards shall be from manufacturers standard product line.1.3 SUBMITTALS*NOTE: Review submittal description (SD) definitions in Section 01 33 00 SUBMITTAL PROCEDURE

18、S and edit the following list to reflect only the submittals required for the project. Submittals should be kept to the minimum required for adequate quality control.A “G” following a submittal item indicates that the submittal requires Government approval. Some submittals are already marked with a

19、“G”. Only delete an existing “G” if the submittal item is not complex and can be reviewed through the Contractors Quality Control system. Only add a “G” if the submittal is sufficiently important or complex in context of the project.For submittals requiring Government approval on Army projects, a co

20、de of up to three characters within the submittal tags may be used following the “G“ designation to indicate the approving authority. Codes for Army projects using the Resident Management System (RMS) are: “AE“ for Architect-Engineer; “DO“ for District Office (Engineering Division or other organizat

21、ion in the District Office); “AO“ for Area Office; “RO“ for Resident Office; and “PO“ for Project Office. Codes following the “G“ typically are not used for Navy, Air Force, and NASA projects.Choose the first bracketed item for Navy, Air Force and NASA projects, or choose the second bracketed item f

22、or Army projects.*Government approval is required for submittals with a “G“ designation; submittals not having a “G“ designation are for Contractor Quality Control approval. information only. When used, a designation following the “G“ designation identifies the office that will review the submittal

23、for the Government. Submit the following in accordance with Section 01 33 00 SUBMITTAL PROCEDURES:SD-03 Product DataVisual Display Board; G; G, _Manufacturers descriptive data and catalog cuts. Manufacturers installation instructions, and cleaning and maintenance instructions.SECTION 10 10 00 Page 5

24、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SD-04 SamplesAluminum; G; G, _Sections of frame, map rail, and chalktray, and two _ map hooks.Porcelain Enamel; G; G, _Section showing porcelain enamel coating, steel, core material and backing.Material

25、s; G; G, _Section of core material showing the lamination of colored cork, natural cork, woven fabric, non-woven fabric, and vinyl wall covering. Sample of hardwood and plastic laminate finish, and glass type. Samples shall be minimum 100 by 100 mm 4 by 4 inches and show range of color.SD-07 Certifi

26、catesVisual Display BoardCertificate of compliance signed by Contractor attesting that visual display board conform to the requirements specified.1.4 DELIVERY, STORAGE, AND HANDLINGDeliver Materials to the building site in the manufacturers original unopened containers and store them in a clean dry

27、area with temperature maintained above 10 degrees C 50 degrees F. Stach materials according to manufacturers recommendations. Visual display boards shall be allowed to acclimate to the building temperature for 24 hours prior to installation.1.5 WARRANTYProvide manufacturers standard performance guar

28、antees or warranties that extend beyond a one year period.PART 2 PRODUCTS2.1 MATERIALS2.1.1 Porcelain EnamelProvide marker board writing surface composed of porcelain enamel fused to a nominal 0.378 mm 28 gauge thick steel, laminated to a minimum 6 mm 1/4 inch thick core material with a steel or foi

29、l backing sheet. Writing surface shall be capable of supporting paper by means of magnets. Marker board surface for display track system may be a powder paint dry erase surface adhered to a nominal 1.214 mm 18 gauge thick steel.2.1.2 CorkCork shall be a continuous resilient sheet made from soft, cle

30、an, granulated cork relatively free from hardback and dust and bonded with a binder suitable for the purpose intended. The wearing surface shall be free from streaks, spots, cracks or other imperfections that would impair SECTION 10 10 00 Page 6Provided by IHSNot for ResaleNo reproduction or network

31、ing permitted without license from IHS-,-,-its usefulness or appearance. The material shall be seasoned, and a clean cut made not less than 13 mm 1/2 inch from the edge shall show no evidence of soft sticky binder.2.1.2.1 Colored CorkProvide colored cork composed of pure cork and natural color pigme

32、nts that are combined under heat and pressure with linseed oil. Colored cork shall be colored throughout and shall be washable. The burlap backing shall be deeply imbedded and keyed to the work sheet being partially concealed in it and meeting the requirements of ASTM F 148.2.1.2.2 Natural CorkMater

33、ial shall be a single layer of pure grain natural cork without backing or facing. The color shall be light tan. The cork sheet shall have a tensile strength of not less than 275 kPa 40 psi when tested in accordance with ASTM F 152.2.1.3 Woven Fabric*NOTE: A multi-colored, patterned, textured fabric

34、will aid in hiding pin and tack holes.Fabric other than manufacturers standard may be used; however there may be an upcharge cost and minimum quantity requirements. Provide minimum generic specifications to obtain fabric required.*Provide plain weave fabric. Fiber content shall be 100 percent polyes

35、ter _. Minimum total weight shall be 496 grams plus or minus 14 grams per linear meter 16 oz. plus or minus 0.5 oz. per lineal yard _. Fabric shall have a Class A flame spread rating of 0-50 and smoke development rating of 0-450 in accordance with ASTM E 84.2.1.4 Non-Woven FabricFabric shall be non-

36、woven and hooktape compatible. Fiber content shall be 100 percent polyester, 100 percent polyolefin or 100 percent nylon _, backed. Minimum total weight shall be 340 grams plus or minus 14 grams per linear meter 11 oz. plus or minus 0.5 oz. per lineal yard for 1524 mm 60 inch wide fabric _. Fabric s

37、hall have a Class A flame spread rating of 0-50 and smoke development rating of 0-450 in accordance with ASTM E 84.2.1.5 Vinyl Wall Covering*NOTE: A multi-colored, textured, vinyl wall covering will aid in hiding pin and tack holes.Vinyl wall covering other than manufacturers standard may be used; h

38、owever there may be an upcharge cost and minimum quantity requirements. Provide minimum generic specifications to obtain fabric required.*SECTION 10 10 00 Page 7Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provide vinyl wall covering conforming to

39、 ASTM F 793, Category V. Vinyl wall covering shall have a Class A flame spread rating of 0-50 and smoke development rating of 0-450 in accordance with ASTM E 84.2.1.6 AluminumAluminum frame extrusions shall be alloy 6063-T5 or 6063-T6, conform to ASTM B 221M ASTM B 221, and be a minimum 1.5 mm 0.06

40、inches thick. Exposed aluminum shall have an anodized, satin finish. Straight, single lengths shall be used wherever possible. Joints shall be kept to a minimum. Corners shall be mitered and shall have a hairline closure.2.1.7 HardwoodExposed hardwood for frames, cabinets, and cases shall be oak, wa

41、lnut or mahogany. Provide hardwood with a durable factory-applied stain and lacquer finish of a type standard with the manufacturer.2.1.8 GlassGlass shall be comprised of tempered glass in accordance with ANSI Z97.1 and shall conform to ASTM C 1048, Kind FT (fully tempered), Condition A (uncoated),

42、Type I, Class I (clear), thickness as specified.2.2 PRESENTATION BOARD*NOTE: A presentation board with an integral pull down projection screen is recommended if projection surface is required. Some units are not available with projection screens. Hot spots may occur if writing surface is used as a p

43、rojection surface.The type of doors, double or single, is dependent on the size of the presentation board.*The presentation board shall be a wall hung cabinet with lockable double doors single door and shall shall not have a projection screen that pulls down over the marker board writing surface in

44、the cabinet interior. The doors shall be attached to cabinet with piano hinges and have a catch or closure to keep doors closed when not in use. The interior of the cabinet shall contain a porcelain enamel markerboard writing surface with chalktray, a flip chart that can be hung on an interior door panel, and fabric covered tacksur