ASD-STAN PREN 2591-D6-1992 Aerospace Series Elements of Electrical and Optical Connection Test Methods Part D6 - Mechanical Endurance (Issue P 1)《航空航天系列 电气和光学连接部件 试验方法 第D6部分 机械耐久性 .pdf

1、Edition approved for publication 1992-06-05 Comments should be sent within six months. C2 Chairman after the date of publication decision Technopolis - 175, rue Jean-Jacques Rousseau 921 38 Issy-les-Moulineaux Cdex - FRANCE A.E.C.M.A. M. J. LE CUNFF ENGLISH VERSION CEN PREN82591 (PART*Db) 92 3404589

2、 0027049 4 Q prEN 2591-D6 Page 3 1 Scope and field of application This standard specifies a method of assessing the operating mechanical endurance of a set of elements of connection without electrical load. It shall be used together with EN 2591. 2 . References EN 2591 EN 2591-A1 EN 2591-81 EN 2591-

3、B2 EN 2591-85 EN 2591-86 EN 2591-87 EN 2591-C12 EN 2591-C13 EN 2591-C14 EN 2591-D8 Aerospace series - Elements of electrical and optical connection - Test methods - General Aerospace series - Elements of electrical and optical connection - Test methods - Part Al - Visual examination 1) Aerospace ser

4、ies - Elements of electrical and optical connection - Test methods - Part B1 - Contact resistance - Low level 1) Aerospace series - Elements of electrical and optical connection - Test methods - Part B2 - Contact resistance at rated current 1) . . Aerospace series - Elements of electrical and optica

5、l connection - Test methods - Part B5 - Housing (shell) electrical continuity 1) Aerospace series - Elements of electrical and optical connection - Test methods - Part 86 - Measurement of insulation resistance 1) Aerospace series - Elements of electrical and optical connection - Test methods - Part

6、B7 - Voltage proof test 1) Aerospace series - Elements of electricai and optical connection - Test methods - Part Cl 2 - Air leakage 2) Aerospace series - Elements of electrical and optical connection - Test methods - Part Cl3 - Driving rain (artificial) 2) Aerospace series - Elements of eiectrical

7、and optical connection - Test methods - Part C14 - Immersion at low air pressure 2) Aerospace series - Elements of electrical and optical connection - Test methods - Part O8 - Mating and unmating forces 2) 1) In preparation at the date of publication of the present standard. 2) Published as AECMA pr

8、e-standard at the date of publication of the present standard. - 7 Previous page is blank CEN PREN*2561L (PAF?T*Db) 92 = 3404589 0027050 O E prEN 2591-D6 Page 4 3 . Preparation of specimens 3.1 Elements of connection shall be fitted with wired contacts. The bundle of wires shall be maintained by the

9、 accessory specified by the technical specification. 3.2 Unless indicated in the technical specification, the following details shall be specified : - type of elements of connection, - type of cable and cross-section, - test is to be carried out manually, - test is to be carried out inechanically, w

10、ith rate of operation, - number of operations, - rate, - method and requirement for final measurements. 4 Method 4.1 Procedure The specimens shall be submitted without electrical load, to the number of mating- unmating operations and at the rate specified by the technical specification. The specimen

11、 shall be mated, locked and unmated so that plug and receptacle are completely separated, which constitutes one cycle. Mating and unmating may be carried out manually or unless otherwise specified by the technical specification with a mechanical device simulating manual operations provided the latte

12、r does not induce any excessive stresses. A counter shall record the number of mating-unmating operations. The specimen shall be operated at the rate specified and for the number of cycles specified by the technical specification. 4.2 Final measurements (if applicable) - EN 2591-A1 - Visual examinat

13、ion - EN 2591-81 or EN 2591-B2 - Contact resistance - EN 2591-B5 - Housing (shell) electrical continuity - EN 259 1 -B6 - Measurement of insulating resistance - EN 259 1 -B7 - Voltage-proof test - EN 2591-D8 - Mating and unmating forces - EN 2591-CI2 or EN 2591-CI3 or EN 2591-CI4 - Sealing, if applicable.