ASD-STAN PREN 3545-007-2013 Aerospace series Connectors electrical rectangular with sealed and non-sealed rear plastic housing locking device operating temperatures - 55 to 175 Par.pdf

1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM prEN 3545-007 Edition P 4 November 2013 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONRue Montoyer 10 - 1000 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.orgICS: Supersedes edition P 3 of A

2、ugust 2004 and will supersede EN 3545-007:2005Descriptors: ENGLISH VERSION Aerospace series Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures 55 C to 175 C Part 007: Cable clamp Product standard Srie arospatiale Connecteurs

3、lectriques, rectangulaires, tanches et non tanches larrire, botier en plastique, verrouillage, tempratures dutilisation 55 C 175 C Partie 007 : Serre-cble Norme de produit Luft- und Raumfahrt Elektrische Rechtecksteckverbinder mit und ohne hintere Abdichtung, Plastikgehuse, Verriegelunssystem, Betri

4、ebstemperaturen von 55 C bis 175 C Teil 007: Zugentlastungsklemme Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aeros

5、pace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-ide

6、ntification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members ha

7、ve then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 1stNovember 2013 Comments should be sent within six months after the date of publication to ASD-STAN El

8、ectrical Domain Copyright 2013 by ASD-STAN prEN 3545-007:2013 (E) 2 Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Terms and definitions . 3 4 Required characteristics . 3 4.1 Dimensions, mass . 3 4.2 Material . 7 4.3 Main general characteristics 7 5 Designation 8 6 Marking . 8 7 Tech

9、nical specification . 8 Figures Figure 1 Dimensions of model Code D 4 Figure 2 Dimensions of model Code E 5 Figure 3 Dimensions of model Code G 6 Figure 4 Dimensions of model Code H 7 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquir

10、ies and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 3545-007:2013 (E) 3 1 Scope This standard specifies cable clamp in the family of rectangular electrical connectors with sealed and

11、 non-sealed rear, plastic housing, locking device, for operating temperatures from 55 C to 175 C. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited a

12、pplies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2591-100, Aerospace series Elements of electrical and optical connection Test methods Part 100: General EN 3545-001, Aerospace series Connectors, electrical, rectangular, with sealed

13、and non-sealed rear, plastic housing, locking device, operating temperatures 55 C to 175 C Part 001: Technical specification EN 3545-002, Aerospace series Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures 55 C to 175 C Part

14、002: Specification of performance and contact arrangements 3 Terms and definitions For the purposes of this standard, the terms and definitions given in EN 2591-100 apply. 4 Required characteristics 4.1 Dimensions, mass The dimensions of attachment system are given in Figure 1, Figure 2 or Figure 3.

15、 Dimensions and tolerances are in millimetres. Mass: 06 g max. for model Code D 09 g max. for model Code E 12 g max. for model Code G 16,5 g max. for model Code H prEN 3545-007:2013 (E) 4 Model Code D General tolerance: 0,2 Figure 1 Dimensions of model Code D prEN 3545-007:2013 (E) 5 Model Code E Ge

16、neral tolerance: 0,2 Figure 2 Dimensions of model Code E prEN 3545-007:2013 (E) 6 Model code G General tolerance: 0,2 NOTE This backshell can be used only with cable gauge 26 to 12. Figure 3 Dimensions of model Code G prEN 3545-007:2013 (E) 7 Model code H General tolerance: 0,2 Figure 4 Dimensions o

17、f model Code H 4.2 Material Material: thermoplastic resin 4.3 Main general characteristics See EN 3545-002. prEN 3545-007:2013 (E) 8 5 Designation EXAMPLE Description block CABLE CLAMP Identity block EN3545-007SCD Number of this standard Cable clamp: SC Model code NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 6 Marking Unless there are other specific contractual requirements, the marking shall include: the identity block as defined in Clause 5; the manufacturers name or trademark. 7 Technical specification See EN 3545-001.