ASD-STAN PREN 3645-009-2017 Aerospace series Connectors electrical circular scoop-proof triple start threaded coupling operating temperature 175 or 200 continuous Part 009 Receptac.pdf

1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM ASD-STAN prEN 3645-009 Edition P 3 September 2017 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Rue Montoyer 10 - 1000 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.org ICS: Supersedes edit

2、ion P 1 of November 2005 and will supersede EN 3645-009:2006 Descriptors: ENGLISH VERSION Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 009: Receptacle, round flange, jam nut mounting Product stand

3、ard Luft- und Raumfahrt Elektrische Rundsteckverbinder, kontaktgeschtzt, drei-gngige Gewinde Schnellkupplung, Dauerbetriebstemperaturen 175 C oder 200 C Teil 009: Fester Steckverbinder mit Mutternbefestigung Produktnorm Srie arospatiale Connecteurs lectriques circulaires contacts protgs, accouplemen

4、t par filetage pas rapide trois filets, tempratures dutilisation 175 C ou 200 C continu Partie 009 : Embase collerette ronde fixation par crou Norme de produit This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association

5、 of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an exte

6、nt that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, the ASD-STAN prEN will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardizatio

7、n) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. ASD-STAN Technical Committee approves t

8、hat: “This document is published by ASD-STAN for the needs of the European Aerospace Industry. The use of this standard is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” A

9、SD-STAN reviews each standard and technical report at least every five years at which time it may be revised, reaffirmed, stabilized or cancelled. ASD-STAN invites you to send your written comments or any suggestions that may arise. All rights reserved. No parts of this publication may be reproduced

10、, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of ASD-STAN. Order details: E-mail: salesasd-stan.org Web address: http:/www.asd-stan.org/ Edition approved for publication 1st

11、September 2017 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2017 ASD-STAN prEN 3645-009:2017 (E) 2 Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Terms and definitions . 3 4 Required characteristics 3 5 Designation . 7

12、 6 Marking . 8 7 Technical specification . 8 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received

13、approval for Publication. prEN 3645-009:2017 (E) 3 1 Scope This standard specifies the characteristics of jam nut mounting receptacles in the family of circular, electrical connectors, with triple start threaded coupling. It applies to models in Table 3. For plugs and protective covers, see EN 3645-

14、006, EN 3645-008, EN 3645-011 and EN 3645-012 respectively. For filler plugs and rear accessories associated with this receptacle, see EN 3645-002. These connectors are derived from and interchangeable with models W, F, J, M, Z, T and K in specification MIL-DTL-38999/24. 2 Normative references The f

15、ollowing documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3645-001,

16、 Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 001: Technical specification EN 3645-002, Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating te

17、mperature 175 C or 200 C continuous Part 002: Specification of performance and contact arrangements EN 3645-006, Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 006: Protective cover for receptacle P

18、roduct standard EN 3645-008, Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 008: Non release plug with grounding ring Product standard EN 3645-011, Aerospace series Connectors, electrical, circular,

19、 scoop-proof, triple start threaded coupling, operating temperature 175 C or 200 C continuous Part 011: Lanyard release plug with grounding fingers Type 1 Product standard EN 3645-012, Aerospace series Connectors, electrical, circular, scoop-proof, triple start threaded coupling, operating temperatu

20、re 175 C or 200 C continuous Part 012: Lanyard release plug with grounding fingers Type 2 Product standard MIL-DTL-38999/24, Connectors, electrical, circular, receptacle, jam-nut mounting, removable crimp contacts, series III, metric 1) 3 Terms and definitions For the purposes of this document, the

21、terms and definitions given in EN 3645-001 apply. 4 Required characteristics 4.1 Dimensions and mass See Figure 1 and Table 1. Dimensions and tolerances are in millimetres. 1) Published by: Department of Defense (DOD), The Pentagon, Washington D.C. 20301 USA. prEN 3645-009:2017 (E) 4 C (without seal

22、) Seal Option D (seal slot with close edges) Key 1 Red strip 4 Blue strip 5 Seal 6 B on flat 2 3 holes 1,5 min. for brake wire (see option according to Detail D) 3 Models J and M: 4,54 00,29 , other models: 3,17 00,45 a Clearance is permissible to accept the accessory mounting. Figure 1 Jam nut rece

23、ptacle prEN 3645-009:2017 (E) 5 Table 1 Jam nut receptacle Dimensions Shell size A B Flat C a D E F b G Thread H 0,3 0,10 0,15 0,10 0,20 0,13 0,03 0,13 max. 09 30,2 16,53 17,40 2,39 1,14 15,9 M171 6g 0,1 R 24,00 21,82 11 34,9 19,07 20,60 18,8 M201 6g 0,1 R 27,00 24,99 13 38,1 23,82 25,40 23,8 M251 6

24、g 0,1 R 32,00 29,77 15 41,3 26,97 28,50 26,8 M281 6g 0,1 R 36,00 32,91 17 44,5 30,15 31,85 30,8 M321 6g 0,1 R c 37,00 36,12 19 49,2 33,32 34,90 3,58 1,91 33,8 M351 6g 0,1 R 41,00 39,25 21 52,4 36,50 37,90 36,8 M381 6g 0,1 R 46,00 42,47 23 55,6 39,67 41,20 39,8, M411 6g 0,1 R 50,00 45,61 25 58,7 42,8

25、5 44,40 42,8 M441 6g 0,1 R 51,23 49,25 P S W Y Z Mass g max. 0,6 0 0,4 0,9 0,1 Aluminium Stainless steel Composite 14,1 27,0 2,2 20,50 20,19 1,85 1,70 15 35 12 31,8 25,27 24,97 21 45 16 34,9 28,45 28,14 27 60 21 38,1 31,62 31,32 32 70 27 41,3 34,80 34,49 40 90 31 46,0 3,0 37,92 37,62 2,69 2,54 49 10

26、4 43 49,2 41,20 40,69 54 117 50 52,4 44,37 43,86 65 132 55 55,6 47,55 47,04 73 158 65 a Dimensions C and 1,5 mm shall be compatible with the panel hole. b Diameter F corresponds to the start of the thread. c Upper diameter modified as follow: 31,95 max. 31,80 min. prEN 3645-009:2017 (E) 6 4.2 Materi

27、als and surface treatment See Table 3. 4.3 Recommended panel cut-out See Figure 2 and Table 2. Dimensions and tolerances are in millimetres. Figure 2 Panel cut-out Panel thickness: 3,20 max. 1,60 min. Table 2 Panel cut-out Dimensions Shell size A B a C 0,25 0 0 0,25 min. 09 17,60 16,70 31,80 11 20,9

28、6 19,59 35,00 13 25,65 24,26 39,40 15 28,83 27,56 42,50 17 32,01 30,73 45,70 19 35,18 33,91 48,50 21 38,35 37,08 51,70 23 41,53 40,26 54,90 25 44,70 43,43 58,00 a Shell size 9, tolerance is 0,060,10 mm. 4.4 Electrical, mechanical and climatic characteristics See EN 3645-002. prEN 3645-009:2017 (E) 7

29、 5 Designation EXAMPLE Description block ELECTRICAL CONNECTOR Identity block EN3645-F7GN16AA Number of the basic standard Model (see Table 3) Shell code for jam nut mounting receptacle (see EN 3645-002) Shell size code (see Table 4) Letter indicating if: N: no grounded cavities G: grounded cavities

30、K: no grounded cavities - specific fluid immersion (Fuel resistance, see EN 3645-001) H: grounded cavities - specific fluid immersion (Fuel resistance, see EN 3645-001) Q: quadrax cavities, grounded L: quadrax cavities, no grounded R: reinforced insert for power contact size 8 Contact arrangement (s

31、ee EN 3645-002) Contact code (see Table 5) Polarization: N, A, B, C, D, E NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. Table 3 Model coding Models Description J Sealed receptacles, with shell in cadmium-plated composite material, olive green

32、 Salt spray resistance 2 000 h Crimped contacts 1 500 operations Maximum operating temperature 175 C continuous. W Sealed receptacles, with shell in cadmium-plated aluminium alloy, olive green Salt spray resistance 500 h Crimped contacts Maximum operating temperature 175 C continuous. Z Sealed recep

33、tacles, zinc-nickel plated aluminium alloy, non-reflective black Salt spray resistance 500 h Crimped contacts Maximum operating temperature 175 C continuous F Sealed receptacles, with shell in nickel-plated aluminium alloy Crimped contacts Maximum operating temperature 200 C continuous. M Sealed rec

34、eptacles, with shell in nickel-plated composite material Salt spray resistance 2 000 h Crimped contacts 1 500 operations Maximum operating temperature 200 C continuous. K Sealed receptacle, with shell in passivated stainless steel Salt spray resistance 500 h Maximum operating temperature 200 C conti

35、nuous. T Sealed receptacle, nickel fluorocarbon polymer plated aluminium alloy Non reflective 500 h salt spray Crimp contacts Maximum operating temperature 175 C continuous. prEN 3645-009:2017 (E) 8 Table 4 Shell size code Shell size Code 09 A 11 B 13 C 15 D 17 E 19 F 21 G 23 H 25 J Table 5 Contact code Contacts Product marking Order coding Supplied without contacts Supplied with contacts EN3155-xxxx2222 EN3155-xxxx2020 EN3155-xxxx1616 EN3155-xxxx1212 EN3155-xxxx1010 Male M A M Female F B F 6 Marking According to EN 3645-001. 7 Technical specification According to EN 3645-001.