ASD-STAN PREN 3682-003-2011 Aerospace series Connectors plug and receptacle electrical rectangular interchangeable insert type rack to panel operating temperature 150 continuous Pa.pdf

1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM prEN 3682-003 Edition P 2 July 2011 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONAvenue de Tervuren, 270 - B-1150 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 775 8131 - www.asd-stan.orgICS: Supersedes editio

2、n P 1 of September 2002 and will supersede EN 3682-003:2006 Descriptors: ENGLISH VERSION Aerospace series Connectors, plug and receptacle, electrical, rectangular, interchangeable insert type, rack to panel, operating temperature 150 C continuous Part 003: Inserts Product standard Srie arospatiale C

3、onnecteurs lectriques rectangulaires rackables, fiches et embases, inserts interchangeables, temprature dutilisation 150 C continu Partie 003 : Inserts Norme de produit Luft- und Raumfahrt Elektrischer Rechtecksteckverbinder, freie und feste Bauform, auswechselbare Isolierkrper, Gestell-Einschubstec

4、kverbinder, Betriebstemperatur 150 C konstant Teil 003: Einstze Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospa

5、ce Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-ident

6、ification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have

7、 then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 1 July 2011 Comments should be sent within six months after the date of publication to ASD-STAN Electrica

8、l Domain Copyright 2011 by ASD-STAN prEN 3682-003:2010 (E) 2 Contents Page Foreword2 1 Scope 3 2 Normative references 3 3 Terms and definitions .3 4 Required characteristics.4 5 Designation 7 6 Marking .9 7 Technical specification .9 Foreword This standard was reviewed by the Domain Technical Coordi

9、nator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 3682-003:2010 (E) 3 1 Scope This standard defines the inserts used in EN 3682 co

10、nnectors. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3682 (all par

11、ts), Aerospace series Connectors, plug and receptacle, electrical, rectangular, interchangeable insert type, rack to panel, operating temperature 150 C continuous 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 3682-001 apply. prEN 3682-003:2010 (E) 4

12、 4 Required characteristics 4.1 Insert interface dimensions for insert with size 22 contact cavities arrangements See Figure 1 and Table 1. Dimensions in millimetres Key 1 Manufacturer name and part number on this side or opposite 2 Interfacial seal 3 Grommet a Interfacial seal applies to socket ins

13、ert only.Figure 1 Table 1 G Housing Cavity A B C D E F cord inside Plug A, C, E 13,13 13,03 12,19 11,56 Receptacle A, C, E 3,55 3,45 2,67 2,03 22,1021,59 39,04 39,002 38,8938,66 40,1839,95 1,50 35,00 Plug B, D, F 13,13 13,03 12,19 11,56 Receptacle B, D, F 3,55 3,45 2,67 2,03 9,40 8,89 27,86427,826 2

14、7,7127,48 29,0128,78 1,50 27,81 prEN 3682-003:2010 (E) 5 4.2 Insert interface dimensions for insert without size 22 contact cavities arrangements See Figure 2 and Table 2. Dimensions in millimetres Key 1 Manufacturer name and part number on this side or opposite 2 Interfacial seal 3 Grommet a Interf

15、acial seal applies to pin insert only.Figure 2 Table 2 G Housing Cavity A B C D E F cord inside Plug A, C, E 15,59 15,49 12,1911,56 Receptacle A, C, E 1,09 0,99 1,14 0,94 22,1021,59 39,0439,002 38,8938,66 40,18 39,95 1,50 35,00 Plug B, D, F 15,59 15,49 12,1911,56 Receptacle B, D, F 1,09 0,99 1,14 0,

16、94 9,40 8,89 27,8627,76 27,7127,48 29,01 28,78 1,50 27,81 prEN 3682-003:2010 (E) 6 4.3 Dimensions of metallic inserts See Figure 3 and Table 3. Dimensions in millimetres Key 1 Manufacturer name and part number on this side or opposite 2 Interfacial seal 3 Grommet a Interfacial seal applies to pin in

17、sert only. b Geometry optional.Figure 3 Table 3 D Housing Cavity A B C cord inside Plug A, C, E 15,59 15,49 Receptacle A, C, E 1,09 0,99 38,89 38,86 40,18 39,95 1,50 35,00 Plug B, D, F 15,59 15,49 Receptacle B, D, F 1,09 0,99 27,81 27,68 29,01 28,78 1,50 35,00 prEN 3682-003:2010 (E) 7 4.4 Design for

18、 insert with two levels front face 62Q2 68Q2 Figure 4 Figure 5 118Q2 68Q4 Figure 6 Figure 7 prEN 3682-003:2010 (E)EN 3682-003:2010 (E) 8 5 Designation 5 EXAMPLE Description block ELECTRICAL CONNECTOR, INSERT Identity block EN 3682 1 P 70 C1 G L Standard reference Type of insert (see Table 4) Housing

19、 Type (R Receptacle, P Plug) Number of signal and power contacts Number of: contacts: Coaxial: Cx (x = quantity) Triaxial: Tx (x = quantity) Quadrax: Qx (x = quantity) Connection to the ground G: coaxial, triaxial and quadrax contacts connected to the ground A: coaxial, triaxial and quadrax contacts

20、 not connected to the ground Contact delivery: if left blank: insert delivered with contacts except coaxial, triaxial and quadrax contacts; L: insert delivered without contacts. Table 4 Type of insert Description 1 For cavities A, C, E 2 For cavities B, D, F prEN 3682-003:2010 (E) 9 6 Marking Insert identification marking, as specified in Clause 5, should be applied in the position shown on the corresponding drawing. In addition, marking shall show: date of manufacture (year week); manufacturer name or trademark. 7 Technical specification See EN 3682-001.