ASD-STAN PREN 3773-006-2015 Aerospace series Circuit breakers single-pole temperature compensated rated currents 1 A to 25 A Part 006 6 3 mm blade terminal Product standard (Editio.pdf

1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM prEN 3773-006 Edition P 1 December 2015 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Rue Montoyer 10 - 1000 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.org ICS: 49.060 Descriptors: ENGLI

2、SH VERSION Aerospace series Circuit breakers, single-pole, temperature compensated, rated currents 1 A to 25 A Part 006: 6,3 mm blade terminal Product standard Luft- und Raumfahrt Schutzschalter, einpolig, temperaturkompensiert, Nennstrme von 1 A bis 25 A Teil 006: Flachsteckverbinder 6,3 mm Produkt

3、norm Srie arospatiale Disjoncteurs unipolaires compenss en temprature, intensits nominales 1 A 25 A Partie 006 : Raccordement par lame 6,3 mm Norme de produit This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association

4、of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an exten

5、t that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vo

6、te and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 1st December 2015 Comm

7、ents should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2015 by ASD-STAN prEN 3773-006:2015 (E) 2 Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Dimensions and mass . 3 4 Characteristics . 6 5 Designation 10 6 Rated current code 10 7

8、 Delivery hardware codes 11 8 Marking .11 9 Technical specification .11 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual,

9、this standard has received approval for Publication. prEN 3773-006:2015 (E) 3 1 Scope This standard specifies the characteristics of single-pole circuit breakers, temperature compensated with a rated current from 1 A to 25 A, used in aircraft on-board circuits at a temperature between 55 C and 125 C

10、 and at an altitude of 15 000 m max. These circuit breakers are operated by a push-pull type single push button (actuator), with delayed action “trip-free“ tripping. They will continue to function up to the short-circuit current. 2 Normative references The following documents, in whole or in part, a

11、re normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2282, Aerospace series Characteristics of aircraft

12、electrical supplies EN 3773-001, Aerospace series Circuit breakers, single-pole, temperature compensated, rated current 1 A to 25 A Part 001: Technical specification EN 3841-100, Aerospace series Circuit breakers Test Methods Part 100: General EN 3841-505, Aerospace series Circuit breakers Test meth

13、ods Part 505: Strength of main terminals EN 6113, Aerospace series Circuit breakers Connecting and attachment hardware EN 9133, Aerospace series Quality management systems Qualification Procedure for aerospace standard parts TR 6083, Aerospace series Cut-outs for installation of electrical component

14、s 1) FED-STD-595B, Colours used in government procurement 2) IEC 60934, Circuit Breakers for equipment 3) 3 Dimensions and mass 3.1 Dimensional characteristics The circuit breakers do not have to correspond to the pictorial illustration, only the dimensions given shall be adhered to. The mounting su

15、rface is the contact surface with the circuit breaker panel. See Figure 1. 1) Published as ASD-STAN Technical Report at the date of publication of this standard (http:/www.asd-stan.org/). 2) Published by: DoD National (US) Mil. Department of Defense (http:/www.defenselink.mil/). 3) Published by: IEC

16、 International Electrotechnical Commission (http:/www.iec.ch/). prEN 3773-006:2015 (E) 4 Standard push button (S): Dimensions are in millimetres prEN 3773-006:2015 (E) 5 Extra length push button (L): Dimensions are in millimetres Key 1 Push button released 7 Mounting surface 2 Push button pressed 8

17、Marking, see Clause 8 9 Optional hole compliant to IEC 60934 Annex E 3 Black conical barrel (C version) 4 Push button released 10 Silver plated blade according to IEC 60934 Annex E 11 Rated current marking (white on black) 12 Positioning lug in accordance with the panel cut-out, as per TR 6083C202 5

18、 Black colour according to FED-STD-595B 6 White Figure 1 Circuit breaker prEN 3773-006:2015 (E) 6 3.2 Electrical diagram See Figure 2. Push button released: CB open. Push button pressed: CB closed. Key 1 Supply 2 Load Load and supply can be inverted. Figure 2 Electrical diagram 3.2.1 Mass Mass shall

19、 not exceed 20 g. 3.3 Panel Mounting Thickness: 1,5 mm to 3 mm. 4 Characteristics 4.1 Material, surface treatment See EN 3773-001. 4.2 Mechanical characteristics 4.2.1 Fasteners None 4.2.2 Recommended tightening torque of attaching nut for installation (4,00 0,25) Nm (for version with threaded barre

20、l and if nut is needed). 4.2.3 Recommended tightening torque of connection hardware for installation With 6,3 mm terminal blades, test EN 3841-505 is not applicable. prEN 3773-006:2015 (E) 7 4.2.4 Resistance to vibrations 4.2.4.1 Combined test: ambient temperature at 70 C and vibrations Sinusoidal :

21、 10 g-PK, see EN 3773-001. Random : 5,8 g-PK, see EN 3773-001. Low frequencies : 10 g-PK, see EN 3773-001. 4.2.4.2 Combined test: ambient temperature at 85 C, altitude and vibrations Sinusoidal: 3 g-PK, see EN 3773-001. 4.2.5 Resistance to shocks 50 g-PK, see EN 3773-001. 4.2.6 Mechanical endurance

22、See Table 6. 4.3 Environment characteristics 4.3.1 Humidity See EN 3773-001. 4.3.2 Corrosion See EN 3773-001. 4.3.3 Contaminating liquids See EN 3773-001. 4.3.4 Overvoltage caused by lightning See EN 3773-001. 4.3.5 Electrical characteristics 4.3.6 Nominal voltage of operational circuits See Table 1

23、. Table 1 Nominal voltage 28 V d.c. 26 V a.c., frequency 400 Hz, single-phase 115 V a.c., frequency 400 Hz, single-phase When using on a variable frequency aircraft power supply, according to EN 2282, limit values (for voltage and frequency) shall be specified. prEN 3773-006:2015 (E) 8 4.3.7 Voltage

24、 drop at n and low current See Table 2. Table 2 Ratings A 1 2 2,5 3 4 5 6 7,5 10 15 20 25 U max. at n V 1,10 0,75 0,70 0,55 0,45 0,35 0,35 0,30 0,30 0,25 0,25 0,20 U max. at 100 mA mV 110 40 30 18 12 8 8 4 3 2,5 2,5 2,5 NOTE The test shall be performed when the contact is established (no switching).

25、 4.3.8 Minimum and maximum tripping thresholds See Table 3. Table 3 Overload (in % of n) Temperatures C Ratings Minimum thresholds value 1 h Maximum thresholds value 1 h On ground At 15 000 m On ground 23 5 All 115 105 140 55 5 115 105 160 70 5 105 100 140 125 5 100 80 140 4.3.9 Overload trip See Ta

26、ble 4. Table 4 Overload (in % of n) 200 500 1 000 Temperatures C Ratings A Trip time s 23 5 1 to 3 2 to 13 0,15 to 2,50 0,035 to 0,600 4 to 15 4 to 18 20 to 25 6 to 20 55 5 All 40 125 5 1,5 prEN 3773-006:2015 (E) 9 4.3.10 Short-circuit values See Table 5. Table 5 Nominal voltage 28 V d.c. 115 V a.c.

27、, 400 Hz c Prospective currents 65 n L/R 1 ms 0,8 cos 1 65 n or 1 000 A r.m.s. (value the most favourable) Test altitudes On the ground and at maximum altitude 15 000 m Number of operations 1 CO a 2 OCO b 1 CO 2 OCO a Removal of short-circuit b Application of a short-circuit c 115 V a.c. covers 26 V

28、 a.c. 4.3.11 No-Load and load endurance See Table 6. Table 6 Number of operations to be provided No-load Load 5 000 2 500 2 500 2 500 2 500 All ratings Main contacts Applicable Resistive Low current 100 mA, 28 V d.c. (rating 3 A) Resistive n, 28 V d.c. Inductive L/R 5 ms n, 28 V d.c. Inductive 0,6 c

29、os 0,7 n, 115 V a.c. - 400 Hz NOTE 1 One operation corresponds to one closing and one opening. NOTE 2 Tolerances 5 % on current, voltage and frequency values. 4.3.12 Dielectric rigidity See Table 7. Voltage at 15 000 m Table 7 Closed position Z = 0 m Z = 15 000 m 1 and 2 with attachment 1 500 V d.c.

30、 400 V d.c. Open position Z = 0 m Z = 15 000 m 1 with 2 1 and 2 with attachment 1 500 V d.c. 400 V d.c. prEN 3773-006:2015 (E) 10 4.3.13 Insulation resistance 100 M (measurement points identical to dielectric rigidity points). 4.3.14 Overload endurance Not applicable. 5 Designation 5.1 Product desig

31、nation EXAMPLE Description block CIRCUIT BREAKER Identity block EN3773-00610ACS Number of EN standard Rated current code (see Table 8) M = Metric threading C = Conical barrel with no threading S = Standard push button L = Extra length push button NOTE If necessary, the code I9005 shall be placed bet

32、ween the description block and the identity block. 5.2 Procurement designation Description block CIRCUIT BREAKER Identity block EN3773-00610ACSC Number of EN standard Hardware delivery code NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 6 Rate

33、d current code See Table 8. Table 8 Ratings n 1 2 2,5 3 4 5 6 7,5 10 15 20 25 Marking on actuator 1 2 2 3 4 5 6 7 10 15 20 25 Rated current code 01A 02A 2A5 03A 04A 05A 06A 7A5 10A 15A 20A 25A prEN 3773-006:2015 (E) 11 7 Hardware delivery codes See Table 9. Table 9 Hardware delivery code Connection

34、and attachment hardware kits EN 6113 Delivery conditions Kit part-No. a Fitted Supplied separately A EN 6113B1 X B EN 6113B1 X C Without connection and attachment hardware kits a Spare parts could be ordered separately, for information see EN 6113. 8 Marking As defined on the drawing and unless othe

35、rwise specified by contract, marking shall include: Preferably on one side: the manufacturers part number the designation defined in 5.1 (without hardware delivery code) the manufacture date (year, week): YYWW Preferably on the other side: the manufacturers name or trademark the terminal identification“1“ and “2“, see 3.2. 9 Technical specification See EN 3773-001.