ASD-STAN PREN 3879-2002 Aerospace Series Metallic Materials Filler Metal for Welding Technical Specification (Edition P2)《航空航天系列 焊接用金属材料填料金属 技术规范 第P2版》.pdf

1、AECMA STANDARDNORME AECMAAECMA NORMprEN 3879Edition P 2April 2002PUBLISHED BY THE EUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES - STANDARDIZATION (AECMA-STAN)Gulledelle 94 B-1200 BRUXELLES Tel. (+32) 2 775 8110 Fax. (+32) 2 775 8111Supersedes edition P 1January 1996ENGLISH VERSIONAerospace seriesMeta

2、llic materialsFiller metal for weldingTechnical specificationSrie arospatialeMatriaux mtalliquesMtaux dapport de soudageSpcification techniqueLuft- und RaumfahrtMetallische WerkstoffeSchweisszusatzTechnische LieferbedingungenThis “Aerospace Series“ Prestandard has been drawn up under the responsibil

3、ity of AECMA-STAN (TheEuropean Association of Aerospace Industries - Standardization). It is published on green paper for theneeds of the European Aerospace Industry. It has been technically approved by the experts of theconcerned Domain following member comments.Subsequent to the publication of thi

4、s Prestandard, the technical content shall not be changed to anextent that interchangeability is affected, physically or functionally, without re-identification of thestandard.After examination and review by users and formal agreement of AECMA-STAN it will be submitted as adraft European Standard to

5、 CEN (European Committee for Standardization) for formal vote.Nota - Extra copies can be supplied by B.N.A.E. Technopolis 54 - 199, rue Jean-Jacques Rousseau 92138 ISSY-LES-MOULINEAUX CEDEXEdition approved for publication2002-04-30Comments should be sent within six monthsafter the date of publicatio

6、n toAECMA-STANGulledelle 94B-1200 BRUXELLESMaterial DomainMr Evetts aecma 2002Page 2prEN 3879: 2002ContentsPage0 Introduction. 31 Scope 32 Normative references. 33 Terms and definitions 44 Wording of order . 45 Health and safety 46 Technical requirements. 4Table 1 Technical requirements for lines 1

7、to 29, where appropriate. 7Table 2 Technical requirements for lines 30 onwards, where appropriate . 13Page 3prEN 3879: 20020 IntroductionThis standard is part of the series of EN metallic material standards for aerospace applications. The generalorganization of this series is described in EN 4258.1

8、ScopeThis standard defines the requirements for the ordering, manufacture, testing, inspection and delivery of allforms of filler metal. It shall be applied when referred to and in conjunction with the EN material standardunless otherwise specified on the drawing, order or inspection schedule.2 Norm

9、ative referencesThis European Standard incorporates by dated or undated reference provisions from other publications.These normative references are cited at the appropriate places in the text and the publications are listedhereafter. For dated references, subsequent amendments to or revisions of any

10、 of these publications applyto this European Standard only when incorporated in it by amendment or revision. For undated referencesthe latest edition of the publication referred to applies.EN 759 Welding consumables Technical delivery conditions for welding filler metals Type ofproduct Dimensions To

11、lerances and markingEN 2000 Aerospace series Quality assurance EN aerospace products Approval of the qualitysystem of manufacturersEN 2032-1 Aerospace series Metallic materials Part 1: Conventional designationEN 2032-2 Aerospace series Metallic materials Part 2: Coding of metallurgical condition in

12、deliveryconditionEN 2078 Aerospace series Metallic materials Manufacturing schedule, inspection schedule,inspection and test report Definition, general principles, preparation and approvalEN 3042 Aerospace series Quality assurance EN aerospace products Qualification procedureEN 4058 Aerospace series

13、 Filler rods and filler wires for welding in titanium and titanium alloys Diameter 0,5 mm D 5,0 mm DimensionsEN 4059 Aerospace series Filler rods and filler wires for welding in steel Diameter 0,5 mm D 5,0 mm DimensionsEN 4060 Aerospace series Filler rods and filler wires for welding in heat resisti

14、ng alloys -Diameter 0,5 mm D 5,0 mm DimensionsEN 4258 Aerospace series Metallic materials General organization of standardization Linksbetween types of EN standards and their useEN 4259 Aerospace series Metallic materials Definition of general terms 1)EN 4268 Aerospace series Metallic materials Heat

15、 treatment facilities General requirements 2)TR 4607 Aerospace series Weldability test for weld filler metal wire 3)1) Published as AECMA Prestandard at the date of publication of this standard2) In preparation at the date of publication of this standard3) In preparation as an AECMA Technical Report

16、 at the date of this standardPage 4prEN 3879: 20023 Terms and definitionsFor the purposes of this standard, the following terms and definitions apply:Definition of general terms, see EN 4259.3.1filler metal for weldingis supplied in the form of: WireWrought product of uniform solid section supplied

17、in coil or on spools. RodWire supplied in straight cut lengths.4 Wording of orderThe order shall clearly indicate: quantities to be supplied; dates of delivery; material standard number; marking method; delivery condition; dimensions and tolerances or reference to an appropriate dimensional standard

18、; forwarding address; nature and type of packing, if required; definition and frequency of any special tests and their retest procedures, if required.5 Health and safetyThe product in the delivery condition shall fulfil the health and safety laws of the area of the country whenand where it is to be

19、delivered.A product safety data sheet shall be available.6 Technical requirements6.1 GeneralThe product shall be manufactured in accordance with the requirements of the relevant material standardand the applicable requirements of this specification. A manufacturing schedule shall be established anda

20、pplied in accordance with EN 2078.Product shall satisfy the requirements of the material standard and/or order and shall be free fromirregularities prejudicial to the subsequent manufacture or use of this product.Not withstanding previous acceptance complying with this material standard, any product

21、 that is found, at alater stage, to contain such defects shall be rejected. Instructions for the use of the material standard arecontained in EN 4258.Unless otherwise specified, the requirements in tables 1 and 2 shall apply in conjunction with those of therelevant material standard. Table 1 relates

22、 to lines 1 to 29 (inclusive) of the material standard and table 2relates to lines 30 onwards in which the sub-line format is also used. Lines 2 to 98 may also be opened inline 100 if the material standard details specific qualification requirements. If a specific line number is notshown in tables 1

23、 and 2, the requirement is stated in the material standard and/or order.Page 5prEN 3879: 20026.2 Qualification requirementsQualification requirements when invoked by the material standard and/or order are detailed in tables 1 and 2.Unless otherwise agreed between the manufacturer and purchaser the q

24、ualification phase shall be run onthe first 3 batches.6.3 Release requirements6.3.1 Release testsRelease testing shall be the responsibility of the manufacturer.The purchaser reserves the right to perform any of the inspections and/or tests required by the materialstandard and/or order.The test samp

25、les shall be representative of the product.When required the manufacturer shall inform the purchaser of the planned dates for extraction of samplesand release testing in order that these operations may be witnessed.Tables 1 and 2 detail the requirements for each line of the material standard. Unless

26、 otherwise specificallyrequested by the purchaser, a particular inspection and/or test for release shall be carried out ifcorresponding acceptance criteria and/or values are stated in the applicable material standard, but see also6.3.5 “Capability clause“.6.3.2 RetestsIf the test procedure or test p

27、iece preparation is faulty, testing shall be re-applied at the original frequencyafter rectification of the original cause of failure.When failure cannot be attributed to faulty testing, or test piece preparation, further test samples shall beselected at twice the original frequency from the product

28、, one of which shall be that on which the originalresults were obtained unless already withdrawn by the manufacturer after suitable identification of the causeof failure. If all retest results are satisfactory, the batch shall be accepted. If one or more tests areunsatisfactory, the batch shall be:

29、rejected, or 100 % retested and the conforming lengths accepted, or partially or fully re-heat treated if heat treatment can rectify the cause of the failure and tested as acompletely new batch except for chemical composition. No product or test sample shall be re-heattreated more than twice.6.3.3 R

30、ejectionAny failure to meet the requirements of the material standard shall be cause for rejection.6.3.4 Special testsSpecial tests may be required by the purchaser. In such cases, the nature of the test, method, frequency andtechnical requirements shall be specified on the order or inspection sched

31、ule and shall be mutually agreedby the manufacturer and the purchaser.6.3.5 Capability clauseWhere the capability clause is invoked and where sufficient statistical evidence exists, the test need not becarried out (unless specifically requested by the purchaser). however, this in no way reduces the

32、obligationsof the manufacturer to fulfil the requirements. If subsequent testing indicates that the product does notcomply with the requirements, the batch shall be rejected.If sufficient statistical evidence does not exist, the test shall be carried out at a frequency agreed betweenthe manufacturer

33、 and purchaser.Page 6prEN 3879: 20026.3.6 Statistical process controlReduction in the extent of release testing, other than that defined in 6.3.5 above may be negotiated with thepurchaser on the basis of appropriate statistical process control and/or statistical data.6.3.7 Inspection and test report

34、The manufacturer shall furnish, with each delivery, a report conforming to the requirements of EN 2078stating the following: manufacturers name and address and, if appropriate, identification of the plant; order number; material standard number; delivery condition and metallurgical code of the produ

35、ct; description of supplies; quantity and dimensions; cast and batch number; results of the mandatory tests, re-tests and chemical analysis; inspection stamp.6.4 TraceabilityEach product shall be traceable to the cast production batch and/or heat treatment batch at all stages ofmanufacture and deliv

36、ery.Page 7prEN 3879: 2002Table 1 Technical requirements for lines 1 to 29, where appropriateFrequency of testingMaterial standard linereferenceNo TitleRequirementsQualification Release1 Material designation See EN 2032-1. 2 Chemical composition The chemical composition shall comply with the requirem

37、ents of the relevant material standard.The chemical composition of each cast shall be determined.Additionally for titanium and titanium alloy filler metal the hydrogen (H2) content shall be determined.Samples for analytical purposes shall be representative of the cast.The method of analysis shall be

38、 at the option of the manufacturer. In cases of dispute the method set out inthe relevant ISO standard shall be used. If no ISO standard exists, an analytical method, that can becalibrated to an agreed reference standard, shall be used.Elements that are not specified in the material standards shall

39、not be intentionally added to the alloy.2 per cast 1 per cast3 Method of melting As stated in the material standard. 4.1 Form Wire and rod 4.2 Method of production Drawing, extrusionIf required by the material standard, filler metal in ferritic steel shall be provided with a copper coating,uniformly

40、 and evenly deposited. The surface shall be cleaned before coating to obtain a good bond.Wire shall be wound on spools in individual layers in such a way that kinks, waves and sharp bends areavoided. The start and end of a wire shall be secured in place. Wire should readily unwind withoutoverlapping

41、 or wedging. Wire on each spool shall be of continuous length and from the same cast. 4.3 Limit dimension(s) Minimum and/or maximum size of the product expressed as a nominal diameter, D, of wire or rod. 5 Technical specification Reference to this technical specification EN 3879. In cases of conflic

42、t, the requirements of the materialstandard shall take precedence over those of this technical specification. continuedPage 8prEN 3879: 2002Table 1 Technical requirements for lines 1 to 29, where appropriate (continued)Frequency of testingMaterial standard linereferenceNo TitleRequirementsQualificat

43、ion Release6.1 Delivery condition The product shall be supplied in the delivery condition specified in this line in the material standard and/oras stated on the order.Marking:The marking shall be durable under the normal conditions of use, storage, handling and shipment.Each rod package shall bear a

44、n adhesive label, bearing the following identification marking: material standard number; delivery condition code; batch number; manufacturers name and, when appropriate, identification of the plant; diameter of the wire rod; weight; inspectors stamp; marking of rods.Rods shall be individually marke

45、d with the material standard number by one of the following methods asdescribed below:a) adhesive labels;b) shrink sleeves;c) impression stamps.Unless otherwise specified on the order, the marking method shall be by :a) adhesive labelsThe method used shall not cause corrosion, crack initiation, cont

46、amination or deformation. continuedPage 9prEN 3879: 2002Table 1 Technical requirements for lines 1 to 29, where appropriate (continued)Frequency of testingMaterial standard linereferenceNo TitleRequirementsQualification Release6.1 Delivery condition(continued)a) Adhesive labelAdhesive labels shall m

47、eet the following requirements: the adhesive type shall provide good adhesion of the label to the product; size approx. 18 mm 18 mm; colour white.The material standard number shall be printed in black with a letter height of 2,5 mm to 3,5 mm(see figure 1). Figure 1 Typical printed labelThe labels sh

48、all be firmly attached to the rods, to prevent lengthwise slip-off, by one of the followingmethods:Method 1:Fold the label in parallel with the imprint, around the rod such that its ends fully overlap (see figure 2)Figure 2 Preferred attachmentMethod 2:Attach two labels to each other over the rod (s

49、ee figure 3)Figure 3 Other types of attachmentcontinuedPage 10prEN 3879: 2002Table 1 Technical requirements for lines 1 to 29, where appropriate (continued)Frequency of testingMaterial standard linereferenceNo TitleRequirementsQualification Release6.1 Delivery condition(continued)b) Shrink sleeves:Shrink sleeves shall meet the following requirements: length (18 1) mm colour whiteThe material standard number sha