ASD-STAN PREN 4008-003-2015 Aerospace series Elements of electrical and optical connection Crimping tools and associated accessories Part 003 Positioner for crimping tool M22520 2-.pdf

1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM prEN 4008-003 Edition P 1 July 2015 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Rue Montoyer 10 - 1000 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.org ICS: 49.060 Descriptors: Aerospace

2、 industry, aerospace equipment, element of electrical connection, electrical contact, characteristics, test, quality assurance, marking ENGLISH VERSION Aerospace series Elements of electrical and optical connection Crimping tools and associated accessories Part 003: Positioner for crimping tool M225

3、20/2-01 Product standard Srie arospatiale Organes de connexion lectrique et optique Outils de sertissage et accessoires associs Partie 003 : Positionneur pour pince sertir M22520/2-01 Norme de produit Luft- und Raumfahrt Elektrische und optische Verbindungselemente Crimpwerkzeuge und zugehriges Zube

4、hr Teil 003: Positionierer fr Crimpzange M22520/2-01 Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry

5、. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification o

6、f the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to im

7、plement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 1er July 2015 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain

8、Copyright 2015 by ASD-STAN prEN 4008-003:2015 (E) 2 Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Terms and definitions .3 4 Required characteristics .3 5 Designation 5 6 Marking .5 7 Technical specification .5 Foreword This standard was reviewed by the Domain Technical Coordinator o

9、f ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 4008-003:2015 (E) 3 1 Scope This standard specifies the characteristics for the positio

10、ner used with the M22520/2-01 crimping tool to crimp electrical contacts according to EN 4008-002. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited

11、applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2591-100, Aerospace series Elements of electrical and optical connection Test methods Part 100: General EN 3155-024, Aerospace series Electrical contacts used in elements of connecti

12、on Part 024: Contacts, electrical, triaxial, size 8, male, type D, crimp, class S Product standard EN 3155-025, Aerospace series Electrical contacts used in elements of connection Part 025: Contacts, electrical, triaxial, size 8, female, type D, crimp, class S Product standard EN 4008-001, Aerospace

13、 series Elements of electrical and optical connection Crimping tools and associated accessories Part 001: Technical specification EN 4008-002, Aerospace series Elements of electrical and optical connection Crimping tools and associated accessories Part 002: List of product standards SAE AS 22520/2-0

14、1, Crimping Tools, Terminal, Hand, Wire Termination for Wire Barrel Sizes 20 through 28 1) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 2591-100 apply. 4 Required characteristics 4.1 Description Securing the positioner on the crimping tool is provi

15、ded by the combined action of the two bayonets and the pressure from the internal spring on the central moving part (locator). The appropriate longitudinal positioning of the contact with respect to the crimping tool indenters is performed by the contact butting against a shoulder on the central par

16、t bore. 1) Published by: SAE National (US) Society of Automotive Engineers http:/www.sae.org/ prEN 4008-003:2015 (E) 4 4.2 Dimensions Dimensions of positioner are given in Figure 1. Dimensions are given in millimetres. General tolerances: 0,127 mm Key 1 Data plate 2 2 places 3 Locator in extended po

17、sition, see Figure 2. 4 Bayonet lock pins 1,07 1,12 5 Mark on this surface: Manufacturers name and Part Number 6 Mark on this surface: EN 4008-003 “use with M22520/2-01 basic tool“ (conform to SAE AS 22520/2-01) Figure 1 Locator assembly Key 1 0,127 45 chamfer Figure 2 Detail A prEN 4008-003:2015 (E) 5 5 Designation EXAMPLE Description block POSITIONER Identity block EN4008-003 Number of this standard NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 6 Marking See Figure 1. 7 Technical specification See EN 4008-001.