ASD-STAN PREN 4008-004-2015 Aerospace series Elements of electrical and optical connection Crimping tools and associated accessories Part 004 Die for crimping tool M22520 5-01 Prod.pdf

1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM prEN 4008-004 Edition P 1 July 2015 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Rue Montoyer 10 - 1000 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.org ICS: 49.060 Descriptors: Aerospace

2、 industry, aerospace equipment, element of electrical connection, electrical contact, characteristics, test, quality assurance, marking ENGLISH VERSION Aerospace series Elements of electrical and optical connection Crimping tools and associated accessories Part 004: Die for crimping tool M22520/5-01

3、 Product standard Srie arospatiale Organes de connexion lectrique et optique Outils de sertissage et accessoires associs Partie 004 : Positionneur pour pince sertir M22520/5-01 Norme de produit Luft- und Raumfahrt Elektrische und optische Verbindungselemente Crimpwerkzeuge und zugehriges Zubehr Teil

4、 004: Positionierer fr Crimpzange M22520/5-01 Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It ha

5、s been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the s

6、tandard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement

7、 the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 1er July 2015 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyrig

8、ht 2015 by ASD-STAN prEN 4008-004:2015 (E) 2 Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Terms and definitions .3 4 Required characteristics .3 5 Designation 6 6 Marking .6 7 Technical specification .6 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-S

9、TANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 4008-004:2015 (E) 3 1 Scope This standard specifies the characteristics for the crimp dies use

10、d with the M22520/5-01 crimping tool to crimp electrical contacts according to EN 4008-002. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies

11、. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2591-100, Aerospace series Elements of electrical and optical connection Test methods Part 100: General EN 4008-001, Aerospace series Elements of electrical and optical connection Crimping

12、tools and associated accessories Part 001: Technical specification EN 4008-002, Aerospace series Elements of electrical and optical connection Crimping tools and associated accessories Part 002: List of product standards SAE AS 22520/5-01, Crimping Tools, Terminal, Hand, Wire Termination. Large for

13、Coaxial, Shielded Contacts and Ferrules, Terminal Lugs, Splices and End Caps 1) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 2591-100 apply. 4 Required characteristics 4.1 Description Securing the dies on the crimping tool is provided by the locati

14、on of the undercut on the die lug into the spring retention mechanism of the crimp tool. The appropriate longitudinal positioning of the contacts with respect to the crimp dies is provided by correct location of the contact into fixed positions on the crimp dies. 1) Published by: SAE National (US) S

15、ociety of Automotive Engineers http:/www.sae.org/ prEN 4008-004:2015 (E) 4 4.2 Dimensions See Figures 1 to 3. Key 1 M10 Cap HD bolt 2 Guide plate 3 Type 2 places Figure 1 Locator assembly prEN 4008-004:2015 (E) 5 Detail A Pin position when jaws are closed Figure 2 Dimensions jaws closed Key 1 Spheri

16、cal radius to blend Figure 3 Indenter prEN 4008-004:2015 (E) 6 5 Designation EXAMPLE Description block CRIMP DIE Identity block EN4008-004 Number of this standard NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 6 Marking See Figure 1. 7 Technical specification See EN 4008-001.