ASD-STAN PREN 4165-004-2001 Aerospace Series Connectors Electrical Rectangular Modular Operating Temperature 175 Degrees C Continuous Part 004 Stackable Mounting Receptacle 2 and 4.pdf

1、AECMA STANDARD NORME AECMA AECMA NORM prEN 41 65-004 Edition P 1 December 2001 PUBLISHED BY THE EUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES - STANDARDIZATION (AECMA-STAN) Gulledelle 94 - 8-1200 BRUXELLES - Tel. (+32) 2 775 81 10 - Fax. (+32) 2 775 81 11 ICs: Descriptors: ENGLISH VERSION Aerospace s

2、eries Connectors, electrical, rectangular, modular Operating temperature 175 OC continuous Part 004: Stackable mounting receptacle 2 and 4 modules series 2 Srie arospatiale Luft- und Raumfahrt :onnecteurs lectriques rectangulaires, modulaires Temprature dutilisation 175 “C continu Partie 004 : Embas

3、e empilable 2 et 4 modules srie 2 Elektrische Rundsteckverbinder Dauebetriebstemperaturen 175 “C konstant Teil 004: Plutton steckverbinder 2 und 4 module serie 2 This “Aerospace Series“ Prestandard has been drawn up under the responsibility of AECMA-STAN (The European Association of Aerospace Indust

4、ries - Standardization). It is published on green paper for the needs of the European Aerospace Industry. It has been technically approved by fhe experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed t

5、o an extent that inferchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of AECMA-STAN it will be submitted as a draft European Standard to CEN (European Committee for Standardization) for forma

6、l vofe. Nota - Extra copies can be supplied by B.N.A.E. - Technopolis 54 - 199, rue Jean-Jacques Rousseau - 92138 ISSY-LES-MOULINEAUX CEDEX Edition approved for publication 2001 -1 2-28 Comments should be sent within six months after the date of publication to Gulledelle 94 AECMA-STAN 6-1200 BRUXELL

7、ES Electrical Domain Mr Peuetta I aecma 20 Page 2 prEN 4165-004: 2001 Blank page e Page 3 prEN 4165-004: 2001 1 Scope This standard defines the stackable mounting receptacle series 2, for 2 or 4 modules used in the family of rectangular electrical modular connectors, operating temperature 175 “C con

8、tinuous. The plug corresponding to those receptacle are defined in EN 4165-002. The protective cover corresponding to those receptacle are defined in EN 41 65-018. 2 Normative references This European standard incorporates by dated or undated reference provisions from other publications. These norma

9、tive references are cited at the appropriate places in the text and the of these publications apply to this European standard only when incorporated in it by amendment or revision. For undated references the lasted edition of the publication refereed to apply. EN 2424 EN 41 65-001 Aerospace series -

10、 Marking of aerospace product Aerospace series - Connectors, electrical, rectangular, modular - Operating temperature 175 “C continuous - Part 001: Technical specification - Product standard 1) EN 41 65-002 Aerospace series Connectors, electrical, rectangular, modular - Operating temperature 175 “C

11、continuous - Part 002: Specification of performance and contact arrangements 1) EN 41 65-003 Aerospace series - Connectors, electrical, rectangular, modular - Operating temperature 175 “C continuous - Part 003: Modules series 2 and series 3 - Product standard 1) EN 41 65-01 8 Aerospace series - Conn

12、ectors, electrical, rectangular, modular - Operating temperature 175 “C continuous - Part 018: Protective cover for receptacle 2 or 4 modules, series 2 and series 3 - Product standard 2) EN 41 65-020 Aerospace series - Connectors, electrical, rectangular, modular - Operating temperature 175 “C conti

13、nuous - Part 020: Coupling system Keway for receptacle - Product standard 2) 3 Terminology See EN 4165-001. 4 Required characteristics See figures I and 2. 1) Published as AECMA Prestandard at the date of publication of this standard. 2) In preparation at the date of publication of this standard. Pa

14、ge 4 prEN 4165-004: 2001 J and M 5 Stackable mounting receptacle, male or female modules 16,OO - 5.1 For 2 modules See EN 4165-003. Dimensions are in millimetres. O0 -o t Figure 1 Table 1 Classes Page 5 prEN 4165-004: 2001 Classes FI W and A 5.2 For 4 modules A Masses max. 9 1520 20,60 See EN 41 65-

15、003. Dimensions are in millimetres. J and M O0 O0 -o t 16,OO 12,50 Figure 2 4 Receptacle with housing (shell) olive drab cadmium plated, aluminium alloy, conducting finish, 500 h resistance to salt mist, maximum operating temperature 175 “C continuous Receptacle with housing (shell) black nickel pla

16、ted, aluminium alloy, 96 h resistance to salt mist, maximum operating temperature 175 “C continuous Receptacle with housing (shell) olive drab cadmium plated, composite material, conducting finish. 500 h resistance to salt mist, maximum operating temperature 175 “C continuous Table 2 A Receptacle wi

17、th housing (shell) nickel plated, composite material, conducting finish, 500 h resistance to salt mist, maximum operating temperature 175 “C continuous Receptacle with housing (shell) black anodised plated, aluminium alloy, no conducting finish, 48 h resistance to salt mist, maximum operating temper

18、ature 175 “C continuous Table 3 - Receptacle classes I I Classes I Description W F J I I - I Page 6 prEN 4165-004: 2001 6 DESIGNATION EXAMPLE: Description block Identity block ELECTRICAL CONNECTOR RECEPTACLE EN41 65FOA4 Number of the basic standard Classes type (see table 3) Type O = Receptacle (see

19、 EN 41 65-002) Type A = Series 2 (see EN 4165-002) Shells type 4 = Stackable mounting receptacle 4 modules 2 = Stackable mounting receptacle 2 modules Receptacle keying coupling (not marked on the connector) Nothing = Not delivered O = Standard Special coding 4 5 6 State of delivery receptacle keying coupling (see EN 41 65-020) (not marked on the connector) O = Delivered: not mounted Mounting in the receptacle 4 5 6 7 Marking Unless there are other specific contractual requirements, the marking shall be in accordance with EN 2424, category P. a Technical specification See EN 4165-001.