ASD-STAN PREN 4165-026-2014 Aerospace series Connector electrical rectangular modular Operating temperature 175 °C continuous Part 026 Accessories for single module connector Produ.pdf

1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM prEN 4165-026 Edition P 2 May 2014 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Rue Montoyer 10 - 1000 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.org ICS: Supersedes edition P 1 of May

2、2010 and will supersede EN 4165-026:2011 Descriptors: ENGLISH VERSION Aerospace series Connector, electrical, rectangular, modular Operating temperature 175 C continuous Part 026: Accessories for single module connector Product standard Srie arospatiale Connecteurs lectriques, rectangulaires, modula

3、ires Temprature dutilisation 175 C continu Partie 026 : Accessoires pour connecteur mono-module Norme de produit Luft- und Raumfahrt Elektrischer Rechtecksteckverbinder in modularer Bauweise Betriebstemperatur 175 C konstant Teil 026: Endgehuse fr Steckverbinder, fr ein Modul Produktnorm This “Aeros

4、pace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain fo

5、llowing member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement o

6、f ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national s

7、tandard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 1st May 2014 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2014 by ASD-STAN prEN 4165-026:2014 (E) 2 Contents Page Foreword 2

8、1 Scope 3 2 Normative references 3 3 Terms and definitions . 3 4 Required characteristics . 4 5 Designation 14 6 Marking . 14 7 Technical specification . 14 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out i

9、n accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 4165-026:2014 (E) 3 1 Scope This standard defines accessories of single modules connectors according to EN 4165-024 and EN 4165-025 used in the family of rec

10、tangular electrical connectors. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenc

11、ed document (including any amendments) applies. EN 2424, Aerospace series Marking of aerospace products EN 3660-033, Aerospace series Cable outlet accessories for circular and rectangular electrical and optical connectors Part 033: Banding bands, style Z, for attachment of screens to cable outlets P

12、roduct standard 1) EN 4165-001, Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 C continuous Part 001: Technical specification EN 4165-002, Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 C continuous Part 002: Specifica

13、tion of performance and contact arrangements EN 4165-024, Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 C continuous Part 024: Single module plug Product standard EN 4165-025, Aerospace series Connectors, electrical, rectangular, modular Operating temperatur

14、e 175 C continuous Part 025: Module receptacle Product Norm 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 4165-001 apply. 1) In preparation at the date of publication of this standard. prEN 4165-026:2014 (E) 4 4 Required characteristics 4.1 Shielded

15、 accessories for single module connector See attachment principle on Figure 1. Always delivered with attachment system. NOTE No accessory is standardized to fit the single-module connectors with contact size 8 module (according to EN 4165-002) a new accessory must be required for standardization if

16、specific need exists. Alternative design: Key 1 Accessory attachment system consisting of half clips. 2 Accessory system consisting of two half sections permitting the termination of shielding using EN 3660-033 banding strap or equivalent. In case of 45 and 90 accessories, numbering system permit to

17、 give indication of angular position of the accessory. Figure 1 Accessory assembly prEN 4165-026:2014 (E) 5 See Figure 2. Dimensions are in millimetres. Detail X (in larger scale) Detail Y (in larger scale) Figure 2 Accessory attachment system prEN 4165-026:2014 (E) 6 4.1.1 Straight accessory Withou

18、t type code See Figure 3. Dimensions are in millimetres. Mass: 5,6 g max. Figure 3 Straight accessory prEN 4165-026:2014 (E) 7 4.1.2 Straight accessory with cable tie device Type code A See Figure 4. Dimensions are in millimetres. Mass: 5,7 g max. Figure 4 Straight accessory with cable tie device pr

19、EN 4165-026:2014 (E) 8 4.1.3 Accessory with angle of 45 Without type code See Figure 5. Dimensions are in millimetres. Mass: 7,5 g max. Key 1 See Note. NOTE Angular position indication (0 to 7) Figure 5 Accessory with angle of 45 prEN 4165-026:2014 (E) 9 4.1.4 Accessory with angle of 45 and cable ti

20、e device Type code A See Figure 6. Dimensions are in millimetres. Mass: 7,5 g max. F view Key 1 See Note. NOTE Angular position indication (0 to 7) Figure 6 Accessory with angle of 45 and cable tie device prEN 4165-026:2014 (E) 10 4.1.5 Accessory with angle of 90 Without type code See Figure 7. Dime

21、nsions are in millimetres. Mass: 9,0 g max. Key 1 Angular position indication (0 to 7) Figure 7 Accessory with angle of 90 prEN 4165-026:2014 (E) 11 4.1.6 Accessory with angle of 90 and cable tie device Type code A See Figure 8. Dimensions are in millimetres. Mass: 9,0 g max. Key 1 See Note. NOTE An

22、gular position indication (0 to 7) Figure 8 Accessory with angle of 90 and cable tie device prEN 4165-026:2014 (E) 12 4.2 Unplated composite accessories for single module connector 4.2.1 Accessory with universal angle Type code C See Figure 9. Dimensions are in millimetres. Mass: 2,2 g max. Figure 9

23、 Accessory with universal angle prEN 4165-026:2014 (E) 13 4.2.2 Accessory with universal angle Type code D See Figure 10. Dimensions are in millimetres. Mass: 2,2 g max. Figure 10 Accessory with universal angle prEN 4165-026:2014 (E) 14 4.3 Class See Table 1. Table 1 Materials and surface treatment

24、Material code Material Surface treatment Resistance to salt mist Operating temperature (continuous) M Receptacle with housing (shell): Composite Nickel plated, conducting finish 500 h 175 C C Composite none na 5 Designation EXAMPLE Description block ELECTRICAL CONNECTOR ACCESSORIES Identity block EN

25、4165M10A Number of the basic standard Classes type, see 4.3 M composite nickel plated Orientation model: 10: Straight, see 4.1.1 and 4.1.2 20: 45 angle, see 4.1.3 and 4.1.4 30: 90 angle, see 4.1.5 and 4.1.6 00: universal angle: see 4.2.1 and 4.2.2 Type code: Without: Without cable tie device accordi

26、ng 4.1.1, 4.1.3 and 4.1.5 A: With cable tie device according 4.1.2, 4.1.4 and 4.1.6 C: Accessory according 4.2.1 D: Accessory according 4.2.2 NOTE If necessary, the code I9005 shall be placed between the description block and the identity block 6 Marking Marking shall be in accordance with EN 2424, category P. 7 Technical specification See EN 4165-001.