ASD-STAN PREN 4165-026-2017 Aerospace series Connector electrical rectangular modular Operating temperature 175 continuous Part 026 Accessories for single module connector Product .pdf

1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM ASD-STAN prEN 4165-026 Edition P 3 June 2017 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Rue Montoyer 10 - 1000 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.org ICS: Supersedes edition P

2、 2 of May 2014 and will supersede EN 4165-026:2015 Descriptors: ENGLISH VERSION Aerospace series Connector, electrical, rectangular, modular Operating temperature 175 C continuous Part 026: Accessories for single module connector Product standard Luft- und Raumfahrt Elektrischer Rechtecksteckverbind

3、er in modularer Bauweise Betriebstemperatur 175 C constant Teil 026: Endgehuse fr Steckverbinder, fr ein Modul Produktnorm Srie arospatiale Connecteurs lectriques, rectangulaires, modulaires Temprature dutilisation 175 C continu Partie 026 : Accessoires pour connecteur mono-module Norme de produit T

4、his “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned

5、 Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal a

6、greement of ASD-STAN, the ASD-STAN prEN will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN t

7、he status of a national standard and by withdrawing any national standards conflicting with the EN. ASD-STAN Technical Committee approves that: “This document is published by ASD-STAN for the needs of the European Aerospace Industry. The use of this standard is entirely voluntary, and its applicabil

8、ity and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” ASD-STAN reviews each standard and technical report at least every five years at which time it may be revised, reaffirmed, stabilized or cancelled. ASD-STAN invit

9、es you to send your written comments or any suggestions that may arise. All rights reserved. No parts of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written

10、permission of ASD-STAN. Order details: E-mail: salesasd-stan.org Web address: http:/www.asd-stan.org/ Edition approved for publication 1st June 2017 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2017 ASD-STAN prEN 4165-026:2017 (E) 2

11、Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Terms and definitions . 3 4 Required characteristics 4 5 Designation . 15 6 Marking . 16 7 Technical specification . 16 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquirie

12、s and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 4165-026:2017 (E) 3 1 Scope This standard defines accessories of single modules connectors according to EN 4165-024 and EN 4165-025

13、used in the family of rectangular electrical connectors. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the lates

14、t edition of the referenced document (including any amendments) applies. EN 3660-033, Aerospace series Cable outlet accessories for circular and rectangular electrical and optical connectors Part 033: Stainless steel banding band, style Z, for attachment of individual and/or overall screens to cable

15、 outlets Product standard1) EN 4165-001, Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 C continuous Part 001: Technical specification EN 4165-002, Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 C continuous Part 002:

16、Specification of performance and contact arrangements EN 4165-024, Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 C continuous Part 024: Single module plug Product standard EN 4165-025, Aerospace series Connectors, electrical, rectangular, modular Operating t

17、emperature 175 C continuous Part 025: Single module receptacle Product standard 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 4165-001 apply. 1) In preparation at the date of publication of this standard. prEN 4165-026:2017 (E) 4 4 Required characte

18、ristics 4.1 Shielded accessories for single module connector See attachment principle on Figure 1. Always delivered with attachment system. NOTE No accessory is standardized to fit the single-module connectors with contact size 8 module (according to EN 4165-002) a new accessory must be required for

19、 standardization if specific need exists. Alternative design: Key 1 Accessory attachment system consisting of half clips 2 Accessory system consisting of two half sections permitting the termination of shielding using EN 3660-033 banding strap or equivalent In case of 45 and 90 accessories, numberin

20、g system permit to give indication of angular position of the accessory. Figure 1 Accessory assembly prEN 4165-026:2017 (E) 5 See Figure 2. Dimensions in millimetres Detail X (in larger scale) Detail Y (in larger scale) Figure 2 Accessory attachment system prEN 4165-026:2017 (E) 6 4.1.1 Straight acc

21、essory Without type code See Figure 3. Mass: 5,6 g max. Dimensions in millimetres Figure 3 Straight accessory prEN 4165-026:2017 (E) 7 4.1.2 Straight accessory with cable tie device Type code A See Figure 4. Mass: 5,7 g max. Dimensions in millimetres Figure 4 Straight accessory with cable tie device

22、 prEN 4165-026:2017 (E) 8 4.1.3 Accessory with angle of 45 Without type code See Figure 5. Mass: 7,5 g max. Dimensions in millimetres Key 1 Angular position indication (0 to 7). Figure 5 Accessory with angle of 45 prEN 4165-026:2017 (E) 9 4.1.4 Accessory with angle of 45 and cable tie device Type co

23、de A See Figure 6. Mass: 7,5 g max. Dimensions in millimetres Key 1 Angular position indication (0 to 7). Figure 6 Accessory with angle of 45 and cable tie device prEN 4165-026:2017 (E) 10 4.1.5 Accessory with angle of 90 Without type code See Figure 7. Mass: 9,0 g max. Dimensions in millimetres Key

24、 1 Angular position indication (0 to 7) Figure 7 Accessory with angle of 90 prEN 4165-026:2017 (E) 11 4.1.6 Accessory with angle of 90 and cable tie device Type code A See Figure 8. Mass: 9,0 g max. Dimensions in millimetres Key 1 Angular position indication (0 to 7) Figure 8 Accessory with angle of

25、 90 and cable tie device prEN 4165-026:2017 (E) 12 4.2 Unplated composite accessories for single module connector 4.2.1 Accessory with universal angle Type code C See Figure 9. Mass: 2,2 g max. Dimensions in millimetres Figure 9 Accessory with universal angle prEN 4165-026:2017 (E) 13 4.2.2 Accessor

26、y with universal angle Type code D See Figure 10. Mass: 2,2 g max. Dimensions in millimetres Figure 10 Accessory with universal angle prEN 4165-026:2017 (E) 14 4.2.3 Accessory with universal angle Type code U See Figure 11. Mass: 2,2 g max. Dimensions in millimetres Key 1 45 steps turnable Figure 11

27、 Accessory with universal angle prEN 4165-026:2017 (E) 15 4.3 Class See Table 1. Table 1 Materials and surface treatment Material code Material Surface treatment Resistance to salt mist Operating temperature (continuous) M Receptacle with housing (shell): Composite Nickel plated, conducting finish 5

28、00 h 175 C C Composite none na 5 Designation EXAMPLE Description block ELECTRICAL CONNECTOR ACCESSORIES Identity block EN4165-026M10A Number of the basic standard Classes type, see 4.3 M composite nickel plated Orientation model: 10: Straight, see 4.1.1 and 4.1.2 20: 45 angle, see 4.1.3 and 4.1.4 30

29、: 90 angle, see 4.1.5 and 4.1.6 00: universal angle: see 4.2.1, 4.2.2 and 4.2.3 Type code: Without: Without cable tie device according 4.1.1, 4.1.3 and 4.1.5 A: With cable tie device according 4.1.2, 4.1.4 and 4.1.6 C: Accessory according 4.2.1 D: Accessory according 4.2.2 U: Accessory according 4.2.3 NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. prEN 4165-026:2017 (E) 16 6 Marking According to EN4165-001. 7 Technical specification See EN 4165-001.