ASD-STAN PREN 4266-2010 Aerospace series Bearing spherical plain metal to metal in corrosion resisting steel cadmium plated Wide series Dimensions and loads Inch series (Edition P .pdf

1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM prEN 4266 Edition P 2 June 2010 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONAvenue de Tervuren, 270 - B-1150 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.orgICS: Supersedes edition P 1 of

2、 November 1996 Descriptors: ENGLISH VERSION Aerospace series Bearing spherical plain, metal to metal, in corrosion resisting steel, cadmium plated Wide series Dimensions and loads Inch series Srie arospatiale Rotules lisses mtal mtal en acier la corrosion, cadmies Srie large Dimensions et charges Sr

3、ies en inches Luft- und Raumfahrt Gelenklager, Metall auf Metall, aus korrosionsbestndigem Stahl, verkadmet Breite Reihe Mae und Belastungen Inch Reihe This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Euro

4、pe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that

5、interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and

6、transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 30 June 2010 Comments should

7、be sent within six months after the date of publication to ASD-STAN Mechanical Domain Copyright 2010 by ASD-STAN prEN 4266:2010 (E) 2 Contents Page Foreword2 1 Scope 3 2 Normative references 3 3 Terms and definitions .4 4 Symbols and abbreviations 4 5 Requirements.4 6 Designation . 13 7 Marking 13 8

8、 Technical specification 13 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Mechanical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publ

9、ication. prEN 4266:2010 (E) 3 1 Scope This standard specifies the characteristics of spherical plain bearings, metal to metal, in corrosion resisting steel, cadmium plated and chromated, wide series, inch series for aerospace applications. They are intended for use in fixed or moving parts of the ai

10、rcraft structure and their control mechanisms. They shall be used in the temperature range 54 C to 150 C. As they are lubricated by means of the following greases: Code A: Grease as per MIL-PRF-23827C, operating temperature range 73 C to 121 C Code B: Grease as per MIL-PRF-81322G, operating temperat

11、ure range 54 C to 177 C. The range of application for bearings lubricated with grease per code A is limited to 121 C. In both cases the spherical surface of the outer or inner ring have to be provided with a dry-film lubricant as per MIL-PRF-46010F or equivalent (anti-seizing protection). The slide

12、hole treatment either at the outer ring or inner ring. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (includ

13、ing any amendments) applies. EN 2030, Steel FE-PM43, Hardened and tempered Bars D 150 mm Aerospace series 1)EN 2133, Aerospace series Cadmium plating of steels with specified tensile strength 1 450 MPa, copper, copper alloys and nickel alloys EN 2337, Aerospace-series Spherical plain bearings Techni

14、cal specificationEN 2424, Aerospace series Marking of aerospace products EN 3161, Aerospace series Steel FE-PM3801 (X5CrNiCu17-4) Air melted Solution treated and precipitation treated Bar a or D 200 mm Rm 930 MPa ISO 1132-1, Rolling bearings Tolerances Part 1: Terms and definitions ISO 8075, Aerospa

15、ce Surface treatment of hardenable stainless steel parts TR 4475, Aerospace series Bearings and mechanical transmissions for airframe applications Vocabulary 2)MIL-PRF-23827C, Grease Aircraft and instrument Gear and actuator screw NATO code number G-354 3)MIL-PRF-46010F, Lubricant Solid film Heat cu

16、red Corrosion inhibiting 3)1) Published as ASD-STAN Standard at the date of publication of this standard by Aerospace and Defence Industries Association of Europe-Standardization (ASD-STAN), (www.asd-stan.org). 2) Published as ASD-STAN Technical Report at the date of publication of this standard by

17、Aerospace and Defence Industries Association of Europe-Standardization (ASD-STAN), (www.asd-stan.org). 3) Published by: Department of Defense (DoD), http:/www.defenselink.mil/. prEN 4266:2010 (E) 4 MIL-PRF-81322G, Grease Aircraft General purpose Wide temperature range NATO code number G-395 3)3 Term

18、s and definitions For the purposes of this document, the terms and definitions given in TR 4475 apply. 4 Symbols and abbreviations Symbols of limit deviations are in accordance with definitions of ISO 1132-1. is the maximum angle of tilt of the outer ring with respect to the inner ring, with the sph

19、erical surface of the outer ring being completely in contact with the inner ring; Ca is the permissible static axial load; Cs is the permissible static radial load; dmp is the single plane mean bore diameter deviation; Dmp is the single plane mean outside diameter deviation; ds is the deviation of a

20、 single bore diameter; Ds is the deviation of a single outside diameter. Definitions and vocabulary according to TR 4475. 5 Requirements 5.1 Configuration, dimensions, tolerances and mass According to Figures 1 and 2 and Table 1. Dimensions and tolerances are expressed in millimetres (inches). Value

21、s apply after to surface treatment. 5.2 Surface roughness In accordance with Figures 1 and 2. Values in micrometres (micro inches), apply prior to surface treatment. 5.3 Material Inner ring: According to EN 2030, hardness 55 HRC 62; Outer ring: According to EN 3161, hardness 28 HRC 38 before swaging

22、 5.4 Surface treatment Without swaging groove code S: Surface treatment according to ISO 8075 for inner ring before swaging. Cadmium plating of outer ring: 5 m to 8 m (0.2 in to 0.3 in) according to EN 2133 (cylindrical surface area and chamfers and both end surfaces at manufactures option), followe

23、d by chromating. With swaging groove code R: Surface treatment according to ISO 8075 for inner ring before swaging. Cadmium plating of outer ring: 5 m to 8 m (0.2 in to 0.3 in) according to EN 2133 (cylindrical surface area, broken angles and radii, respectively, as well as both end surfaces up to t

24、he swaging grooves), followed by chromating. prEN 4266:2010 (E) 5 5.5 Loads and clearances According to Tables 2 and 3. aSet back bFor the inner ring cFor the outer ring dCadmium plated Figure 1 Code S Without swaging grooves prEN 4266:2010 (E) 6 aSet back bFor the inner ring cFor the outer ring dCa

25、dmium plated Figure 2 Code R With swaging grooves prEN 4266:2010 (E) 7 Figure 3 Grease hole code “E” Without grease hole and lubricating groove aThree holes e distributed over the circumference at distance of 120 Figure 4 Grease hole code “F” With grease hole on inner ring and lubricating groove on:

26、 Bore of inner ring Spherical surface of the outer ring The hole should allow the passage of the grease prEN 4266:2010 (E) 8 aThree holes e distributed over the circumference at distance of 120 Figure 5 Grease hole code “G” With grease hole on outer ring and lubricating groove on: Outer surface of o

27、uter ring Spherical surface of the outer ring The hole should allow the passage of the grease prEN 4266:2010 (E) 9 Table 1 Dimensions, tolerances and mass Dimensions in millimetres (in inches) Diameter B C d1d2d3d D Limit deviation 0 0,05 0,13 0 0 0,05 Diameter code admp ds Dmp Ds 0.002000.005min. 0

28、.002003 4,826 (0.190 0) 04 6,350 (0.250 0) 15,875(0.625 0) 8,31 (0.327) 7,62 (0.300) 13,5(0.53) 14,30 (0.563) 05 7,938 (0.312 5) 17,463(0.750 0) 0.0080 30.000011,10 (0.437) 8,05 (0.317) 9,14 (0.360) 14,4(0.57) 15,88 (0.625) 06 9,525 (0.375 0) 20,638(0.812 5) 12,70 (0.500) 10,31 (0.405) 11,84 (0.466)

29、 17,4(0.69) 18,08 (0.712) 07 23,813(0.9375) 21,26 (0.837) 07A 11,113 (0.437 5) 23,017(0.906 2) 14,27 (0.562) 11,23 (0.442) 13,64 (0.537) 19,7(0.78) 20,52 (0.808) 08 12,700 (0.500 0) 25,400(1.000 0) 15,88 (0.625) 12,83 (0.505) 15,42 (0.607) 22,1(0.87) 22,86 (0.900) 09 14,288 (0.562 5) 28,575(1.125 0)

30、 17,45 (0.687) 13,61 (0.536) 18,31 (0.721) 25,4(1.00) 26,04 (1.025) 10 15,875 (0.625 0) 30,163(1.187 5) 0,0090 40.000019,05 (0.750) 14,40 (0.567) 18,97 (0.747) 26,9(1.06) 27,61 (1.087) 12 19,050 (0.750 0) 34,925(1.375 0) 16,00 (0.630) 21,46 (0.845) 31,0(1.22) 31,78 (1.251) 14 22,225 (0.875 0) 41,275

31、(1.625 0) 0,0130 50.00000,0110 40.00000,0130 50.000022,23 (0.875) 19,18 (0.755) 25,27 (0.995) 33,7(1.33) 38,13 (1.501) 16 25,400 (1.000 0) 53,975(2.125 0) 34,93 (1.375) 25,53 (1.005) 32,23 (1.269) 47,5(1.87) 50,83 (2.001) 20 31,750 (1.2500) 60,325(2.375 0) 38,10 (1.500) 28,70 (1.130) 37,13 (1.462) 5

32、3,2(2.09) 57,18 (2.251) 24 38,100 (1.500 0) 68,263(2.687 5) 42,85 (1.687) 31,06 (1.223) 43,10 (1.697) 60,8(2.39) 65,10 (2.563) 28 44,450 (1.750 0) 76,200(3.00) 46,02 (1.812) 33,45 (1.317) 49,91 (1.965) 67,9(2.67) 73,05 (2.876) 32 50,800 (2.000 0) 82,550(3.250 0) 00,13 50.00000,0150,00360.00010.0000,

33、0130 50.00000,0150,00360.00010.00049,20 (1.937) 35,05 (1.380) 56,10 (2.209) 74,6(2.94) 79,35 (3.124) continued prEN 4266:2010 (E) 10 Table 1 (concluded) Dimensions in millimetres (in inches) P efr1r2 r3 b U t Mass 0 0,25 0,20 0,20 0 0,25 degree degree g/piece Diameter code a 0.0100( 0.008) ( 0.008)

34、0.0100min. 0,5 max. 03c 13 04c16,0 20 12 05c0,64 (0.025) 0,127 to 0,254 00.010to00.00515,5 0,08 (0.003) 0,5 (0.02) 13 06c 0,64 (0.025) 9,5 23 07 0,76 (0.030) 33 07A 11,0 30 08 9,5 40 09 1,50 (0.059) 10,5 56 10 0,89 (0.035) 0,76 (0.030) 12,0 0,8 (0.03) 63 12 2,00 (0.079) 2,80 (0.110) 14,0 92 14 6,0 1

35、46 16 14,5 392 20 12,5 499 24 14,0 668 28 859 32 1,40 (0.055) 2,50 (0.098) 4,00 (0.157) 1,02 (0.040) 0,13 to 0,38 50.010to00.005 0,254 to 0,432 00.017to00.01013,0 30 0,12 (0.005) 1,2 (0.05) 1 005 aThe diameter code corresponds to bore diameter d in 1/16inch. bThe acceptance value is the maximum valu

36、e for the user. cNot available with lubrification code F or code G. prEN 4266:2010 (E) 11 Table 2 Loads Permissible static load kN Ultimate static load kN Radial b c CsAxial b d e CaRadial b Axial b Diameter code a Code E Code F/G Code E Code F/G Code E Code F/G Code E Code F/G 03f10,7 g 16,1 g 04f2

37、4,5 g 19,3 36,7 g 29,0 05f47,8 g 18,0 71,6 g 26,9 06f72,1 g 27,4 108,2 g 41,1 07 07A100,8 71,5 33,5 30,7 151,1 107,2 50,3 46,0 08 131,7 99,0 45,6 42,7 197,6 148,3 68,3 64,1 09 161,0 123,5 52,1 49,3 241,5 185,2 78,2 73,9 10 182,4 142,5 59,2 56,4 273,6 213,7 88,8 84,5 12 222,7 176,8 66,8 64,0 334,1 26

38、5,3 100,2 96,0 14 299,3 228,0 101,7 96,0 449,0 342,0 152,6 143,9 16 497,4 g 481,9 193,3 187,5 746,1 g 722,8 289,9 281,3 20 741,6 628,8 249,9 244,1 1 112,3 943,2 374,8 366,2 24 923,2 794,3 296,8 291,0 1 384,8 1 191,5 445,1 436,5 28 1 117,2 973,3 348,3 342,5 1 675,8 1 460,0 522,5 513,8 32 1 291,21 133

39、,0 385,1 379,4 1 936,81 699,6 577,7 569,0 aThe diameter code corresponds to bore diameter d in 1/16 inch. bDefinition and testing for permissible and ultimate static loads according to EN 2337 and TR 4475. cPermissible surface pressure 530 MPa, definition per TR 4475. dThese values apply to loose sp

40、herical bearings. For installed bearings, the push-out loads may be smaller than these values. ePermissible surface pressure 460 MPa, definition per TR 4475. fNot available with lubrification code F or code G. gLimit by bolt bending. Definition: solid shaft; rigid clamping on both sides; uniform loa

41、d; permissible bending stress 1 350 MPa; permissible shear stress 1 200 MPa. prEN 4266:2010 (E) 12 Table 3 Clearance Clearance b Radial Axial Normal Code N Reduced Code P Normal Code N Reduced Code P Diameter code a max. max. 03 04 05 06 07 07A 0,010 to 0,030 (0.0004 to 0.0012) 0,12 (0.005) 08 0,002

42、 to 0,010 (0.0001 to 0.0004) 0,035 (0.0014) 09 10 0,003 to 0,012 (0.0001 to 0.0005) 0,040 (0.0016) 12 14 16 20 24 28 0,004 to 0,015 (0.00015 to 0.0006) 0,050 (0.0020) 32 0,010 to 0,050 (0.0004 to 0.0020) 0,005 to 0,020 (0.0002 to 0.0008) 0,229 (0.0090) 0,060 (0.0024) aThe diameter code corresponds t

43、o nominal diameter d in 1/16 inch. bDefinition and testing for clearance according to EN 2337. prEN 4266:2010 (E) 13 6 Designation EXAMPLE Description block BEARING Identity block EN4266BP16ER Number of this standard Grease code (see Clause 1) Clearance code (see Table 3) Diameter code (see Table 1)

44、 Grease hole code (see Figures 3, 4 and 5) Swaging groove code (see Figures 1 and 2) NOTE If necessary, the code I9005shall be placed between the description block and the identity block. 7 Marking According to EN 2424, style A. In addition, the bearing may be marked with manufacturers part number. Marking position and method are at manufacturers option. 8 Technical specification According to EN 2337.