1、AECMA STANDARD NORME AECMA AECMA NORM prEN 4416 Edition P 1 February 2005 PUBLISHED BY THE EUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES - STANDARDIZATION b Gulledelle 94 - 8-1200 Brussels -Tel. 32 2 775 81 10 - Fax. 32 2 775 811 1 - www.aecma-stan.org ICs: Descriptors: ENGLISH VERSION Srie arospatia
2、le Matriaux non-mtalliques Textiles Tissus Spcification technique Aerospace se ries Non-metallic materials Textiles Wide woven fabrics Technical specification Luft- und Raumfahrt Nichtmetallische Werkstoffe Textilien Gewebe Technische Lieferbedingungen This “Aerospace Series“ Prestandard has been dr
3、awn up under the responsibility of AECMA-STAN (The European Association of Aerospace Industries - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the p
4、ublication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is afiected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of AECMA-STAN, it will be submitted as a draf
5、t European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national st
6、andards conflicting with the EN. Edition approved for publication 28 February 2005 Comments should be sent within six months after the date of publication to AECMA-STAN Non-metallic Material Domain Copyright 2005 O by AECMA-STA! Page 2 prEN 441 6:2005 Foreword This standard was reviewed by the Domai
7、n Technical Coordinator of AECMA-STANS Non-metallic Material Domain . After inquiries and votes carried out in accordance with the rules of AECMA-STAN defined in AECMA- STANS General Process Manual. this standard has received approval for Publication . Contents Page O Introduction . 1 Scope 2 Normat
8、ive references . 3 Definitions and abbreviations 4 Requirements 5 Qualification 6 Release testing 7 Preparation for delivery . 8 Declaration of conformity Annex A (normative) Table of testing requirements Annex B (normative) Defects. methods of marking and acceptance limits . Annex C (normative) Mar
9、king media for textiles Annex D (informative) Dyed textiles . . 3 3 3 4 5 8 9 10 12 13 14 17 19 Page 3 prEN 441 6:2005 O Introduction This standard is part of the series of EN non-metallic material standards for aerospace applications. The general organisation of this series is described in EN 4385.
10、 This standard is a level 2 document as defined in EN 4385. 1 Scope This standard defines the requirements for manufacture, inspection and testing of wide woven fabrics for aerospace applications. 2 Normative references This European Standard incorporates by dated and undated references, provisions
11、from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of the publications apply to this European standard only when incorporated in it by amendm
12、ent or revision. For undated references the latest edition of the publication referred to applies. IS0 105-BO2 IS0 105-E01 IS0 105-XI2 IS0 2060 IS0 2061 IS0 2062 IS0 5084 IS0 8498 IS0 13934-1 IS0 13935-1 IS0 13937-4 Textiles - Tests for colour fastness - Part B02: Colour fastness to artificial light
13、: Xenon arc fading lamp test Textiles - Tests for colour fastness - Part 01: Colour fastness to water Textiles - Tests for colour fastness - Part X12: Colour fastness to rubbing Textiles - Yarn from packages - Determination of linear density (mass per unit length) by the skein method Textiles - Dete
14、rmination of twist in yarns - Direct counting method Textiles - Yarns from packages - Determination of single-end breaking force and elongation at break Textiles - Determination of thickness of textiles and textile products Woven fabrics-Description of defects- Vocabulary Textiles - Tensile properti
15、es of fabrics - Part 1: Determination of maximum force and elongation at maximum force using the strip method Textiles - Seam tensile properties of fabrics and made-up textile articles - Part 1: Determination of maximum force to seam rupture using the strip method Textiles - Tear properties of fabri
16、cs - Part 4: Determination of tear force of tongue-shaped test specimens (Double tear test) ISO/IEC Guide 22 General criteria for suppliers declaration of conformity EN 1049-2 Textiles - Woven fabrics - Construction - Methods of analysis - Part 2: Determination of number of threads per unit length E
17、N 1773 Textiles - Fabrics - Determination of width and length EN 2000 Aerospace series - Quality assurance - EN aerospace products - Approval of the qualify system of manufacturers Page 4 prEN 441 6:2005 EN 3042 EN 4385 EN 4426 EN 4427 EN 4430 EN 4503 EN 4507 EN 12127 EN 12562 EN 20139 EN 26330 TR 7
18、000-1 Aerospace series - Quality assurance - EN aerospace products - Qualification procedure Aerospace series - Non-metallic materials - General organisation of standardisation - Links between types of standards 1) Aerospace series - Non-metallic materials - Textiles - Test method - Determination of
19、 conductivity and pH of aqueous extracts 1) Aerospace series - Non-metallic materials - Test Method - Determination air permeability of parachute canopy fabrics 2) Aerospace series - Non-metallic materials - Test Method - Determination of lengthways distortion 2) Aerospace series - Non-metallic mate
20、rials - Textiles - Test method - Determination of water soluble chloride and sulfate of aqueous extracts 1) Aerospace series - Non-metallic materials - Textiles - Test method - Determination of water extractable matter 1) Textiles - Fabrics - Determination of mass per unit area using small samples T
21、extiles - Para-aramid multifilament yarns - Test methods Textiles - Standard atmospheres for conditioning and testing Textiles - Domestic washing and drying procedures for textile testing Aerospace series - Non-metallic materials - Rules for the drafting and presentation of material standards - Part
22、 1: General rules 3) 3 Definitions and abbreviations 3.1 Definitions For the purpose of this standard the definitions in EN 2000 and EN 3042 apply. In addition, the following definitions are applicable. 3.1.1 Batch 3.1 .I .I loomstate fabric for loomstate fabric, both a Production Batch and an Inspe
23、ction Batch are the quantity of fabric produced from one weavers beam or one continuously woven length not exceeding 5 O00 metres, provided that weft yarn of consistent and proven quality has been used If a fresh delivery of weft yarn of unproven quality is introduced during weaving the warp, a fres
24、h NOTE batch has been created. 3.1.1.2 piece treated fabric for piece treated fabric, both a Finishers Batch and an Inspection Batch are the quantity of fabric subject to finishing processes in one continuous length not exceeding 5 O00 metres If several small batches are brought together during the
25、finishing process to form one large NOTE Finishers Batch, due note should be taken of the need to maintain identification of each individual batch. 1) Published as AECMA Prestandard at the date of publication of this standard 2) In preparation at the date of publication of this standard 3) Published
26、 as AECMA Technical Report at the date of publication of this standard Page 5 prEN 4416:2005 3.1.2 defect a fault that would reduce the expected performance of the fabric or, if it appeared in a prominent position in an article made from the fabric, would readily be seen and rejected by a prospectiv
27、e purchaser. For definitions of specific defects refer to IS0 8498. 3.1.3 fabric a manufactured assembly of fibres and / or yarns that has substantial surface area in relation to its thickness and sufficient mechanical strength to give the assembly inherent cohesion 3.1.4 manufacturer the firm makin
28、g the material into the form (yam, loomstate fabric, finished fabric, etc.) in which it is consigned to the purchaser 3.1.5 product in this document the word product refers to all forms of wide woven fabric 3.1.6 purchaser the body which purchases the product from a manufacturer or a stockist in acc
29、ordance with the requirements of the user NOTE The purchaser may also be the user. 3.1.7 supplier the firm consigning the material to the purchaser NOTE The supplier may be either the manufacturer or the stockist. 3.1.8 textile any fabric (however constructed), sewing thread or cordage made from nat
30、ural or man made fibres and / or yarns, and blends of these 3.1.9 wide woven fabric any fabric woven at more than 450 mm width between selvedges 3.2 Abbreviations Not applicable 3.3 Conventions Not applicable 4 Req u remen ts 4.1 4.1 .I Manufacturing schedule The product shall be manufactured to ful
31、fil the requirements of the relevant material standard and this technical specification. The manufacturer shall define the raw material, processes and inspection requirements in a manufacturing schedule. Ge ne ral req u i remen ts Page 6 prEN 441 6:2005 4.1.2 Traceability All products shall be trace
32、able to the raw material batches at all stages of manufacture and delivery. Similarly, each raw material batch shall be traceable to all products at all stages of manufacture and delivery. 4.1.3 Freedom from defects All products shall be free from defects not complying with the requirements of the m
33、aterial standard or order and this technical specification, or which may be prejudicial to the subsequent manufacture and/or use of the products. The requirements for freedom from defects are given in Annex B of this specification. Marking media to be used for the identification of defects on textil
34、es shall conform to the requirements of Annex C of this specification. 4.1.4 Health and safety It is the responsibility of the supplier to establish satisfactory health and safety information to ensure conformity with any European, National or local lawdregulations. 4.1.5 Dimensions 4.1.5.1 General
35、Dimensions and tolerances shall conform to the requirements of the order or drawing and unless otherwise specified in the individual material standard, with subclauses 4.1 5.2 to 4.1 5.5. If loomstate fabric is subsequently to be processed, e.g. scoured, dyed or coated, allowance should NOTE be made
36、 for the consequent shrinkage. 4.1.5.2 Overall width When measured in accordance with the test method listed in Annex A, the width of the fabric shall be not less than that specified in the individual textile specification. The variation in width shall not exceed 15 mm. 4.1.5.3 Length When measured
37、in accordance with the EN 1773 the length of the product shall conform to the following. a) Fabric for coating shall consist of continuous lengths without gross defects and with not more than one butt seam per 200 m length. No part shall be less than 40 m long. b) For other fabrics the minimum lengt
38、h of the loomstate piece shall be 100 m for those having a mass per unit area of 450 g/m2 or less, and 50 m for those having a mass per unit area of more than 450 g/m2. Not more than 5 % of the pieces shall be in three parts, not more than 25 % of the remainder shall be in two parts and no part shal
39、l be less than 15 m long. 4.1 54 Lengthways distortion When measured in accordance with the test method listed in Annex A, lengthways distortion shall not exceed 2,5 % for fabrics of 100 g/m2 or less and shall not exceed 5 % for fabrics of more than 100 g/m2 . 4.1.6 Manufacture 4.1.6.1 The wide wove
40、n fabric shall be uniformly manufactured. 4.1.6.2 The edges shall be straight and even and shall not be substantially thicker than the body of the fabric. NOTE Certain weaving processes generate selvedges that may be slightly thicker than the body of the fabric. Any difference in thickness should be
41、 kept to a minimum so as not to hinder the accurate cutting of panels from multiple layers of fabric. 4.1.6.3 The fabric shall lie flat on a table. 4.1.6.4 lengthways tension, and weft skew and bow shall conform to the individual textile material specification. Fabric supplied for subsequent coating
42、 shall continue to lie flat on a table when subjected to Page 7 prEN 4416:2005 4.1.7 Dyed textiles 4.1.7.1 Dyestuffs Sulfur dyes and dyes known to accelerate actinic damage shall not be used (see Annex D). 4.1.7.2 Colour fastness Unless otherwise stated in the material standard, the following minimu
43、m colour fastness ratings shall apply when tested in accordance with the test methods listed in Annex A, of this specification; a) Cellulosic Fastness to light Fastness to water Fastness to rubbing 5 3 (change of colour) 3 (staining adjacent fabric) 4 (dry staining) 3 (wet staining) b) Wholly or par
44、tly synthetic Fastness to light 4 Fastness to water Fastness to rubbing 4 (change of colour) 4 (staining adjacent fabric) 4 (dry staining) 3 (wet staining) The test for fastness of colour to light shall be a Type Test (see Clause 5). 4.1.8 Freedom from corrosive impurities 4.1.8.1 method listed in A
45、nnex A, of this specification, the result shall not exceed 15 mS/m. When tested to determine the conductivity of an aqueous extract in accordance with the test 4.1.8.2 If the conductivity of the aqueous extract exceeds 15 mS/m e.g. owing to the presence of adventitious conducting, but not specially
46、corrosive material, then the following shall apply, when tested in accordance with the test methods listed in Annex A: a) the pH value of the aqueous extract shall be not less than 5,O nor more than 8,0, b) the percentage of water soluble chloride expressed as sodium chloride, shall not exceed 0,lO
47、%, c) the percentage of water soluble sulfate expressed as anhydrous sodium sulfate, shall not exceed 0,25 %. 4.1.9 Yarn 4.1.9.1 The yarn(s) used in the manufacture of the product shall be as specified in the material standard. 4.1.9.2 Unless otherwise stated in the material standard, the properties
48、 of the yarn(s) shall be determined in accordance with the test methods listed in Annex A of this specification. The results of the tests shall conform to the requirements specified in the material standard. 4.1.9.3 The yarn tests shall be Type Tests (see Clause 5). 4.1 .IO Construction 4.1.10.1 The
49、 product shall be constructed as specified in the material standard. 4.1.10.2 Unless otherwise stated in the material standard, the construction of the product shall be determined in accordance with the test methods listed in Annex A, of this specification. The results of the tests shall conform to the requirements specified in the material standard. Page 8 prEN 441 6:2005 4.1 .I1 Dyeing and finishing 4.1.11.1 The product shall be dyed and finished as specified in the material standard. 4.1.11.2 If required dyed and providing that this is permitted by the material standard,
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1