ASD-STAN PREN 4530-006-2005 Aerospace Series Sealing Sleeves Used in Elements of Connection Part 006 Sealing Sleeves for External Diameter Cable 4 68 mm to 5 05 mm Product Standard.pdf

1、AECMA STANDARD NORME AECMA AECMA NORM prEN 4530-006 Edition P 1 June 2005 PUBLISHED BY THE EUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES - STANDARDIZATION Gulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8110 - Fax. + 32 2 775 8111 - www.aecma-stan.orgICS: 49.060 Descriptors: ENGLISH VERSION Aerospa

2、ce series Sealing sleeves used in elements of connection Part 006: Sealing sleeves for external diameter cable 4,68 mm to 5,05 mm Product standard Srie arospatiale Manchons dtanchit utiliss dans les organes de connexion Partie 006 : Manchons dtanchit pour cbles de diamtre extrieur 4,68 mm 5,05 mm No

3、rme de produit Luft- und Raumfahrt Dichtungshlse zur Verwendung in Verbindungselementen Teil 006: Dichtungshlse fr Leitungen mit einem Aussendurchmesser von 4,68 mm bis 5,05 mm Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of AECMA-STAN (The European Asso

4、ciation of Aerospace Industries - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not

5、be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of AECMA-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standa

6、rdization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publicatio

7、n 30 June 2005 Comments should be sent within six months after the date of publication to AECMA-STAN Electrical Domain Copyright 2005 by AECMA-STAN prEN 4530-006:2005Foreword This standard was reviewed by the Domain Technical Coordinator of AECMA-STANs Electrical Domain. After inquiries and votes ca

8、rried out in accordance with the rules of AECMA-STAN defined in AECMA-STANs General Process Manual, this standard has received approval for Publication. Contents Page 1 Scope . 3 2 Normative references 3 3 Terms and definitions . 3 4 Required characteristics 3 5 Designation. 6 6 Marking 6 7 Delivery

9、 conditions 6 8 Technical specification 6 2 prEN 4530-006:20051 Scope This standard specifies the required characteristics and test applicable to sealing sleeves used in elements of connection according to EN 3155-002 and EN 4530-002. 2 Normative references The following referenced documents are ind

10、ispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2591*, Aerospace series Elements of electrical and optical connection Test methods. EN 3

11、155-002, Aerospace series Electrical contacts used in elements of connection Part 002: List and utilization of contacts.1)EN 3682-001, Aerospace series Connectors, plug and receptacle, electrical, rectangular, interchangeable insert type, rack to panel, operating temperature 150 C continuous Part 00

12、1: Technical specification.1)EN 4530-001, Aerospace series Sealing sleeves used in elements of connection Part 001: Technical specification.1)EN 4530-002, Aerospace series Sealing sleeves used in elements of connection Part 002: List and utilization of sealing sleeves.1)3 Terms and definitions For t

13、he purposes of this document, the terms and definitions given in EN 4530-001 apply. 4 Required characteristics 4.1 Specific characteristics Sealing sleeves are for general application and class R corresponds to an operating temperature range from 65 C to 150 C. 4.2 Dimensions and mass See Figure 1.

14、Dimensions and tolerances are given in millimetres. * And all its parts quoted. 1) Published as AECMA Prestandard at the date of publication of this standard. 3 prEN 4530-006:20051 Key 1 See Table 1. Figure 1 4.3 Material Fluoro silicone. 4.4 Typical cables The cable diameter should be within 4,68 m

15、m to 5,05 mm (see Table 1). Table 1 Permissible cable code External diameter cable A 4,68 mm to 5,05 mm 4.5 Assembly instructions The sealing sleeve should be positioned over the cable prior to assembly of the contact onto the wire, the rigid side towards the connector. After contact insertion in th

16、e connector, the sleeve should be slid inside the cavity until it bottoms. 4.6 Tooling Not applicable 4 prEN 4530-006:2005 4.7 Test See Table 2. Table 2 Applicable EN 2591- Test Not applicableAccording to EN 3155-001 Remarks 101 Visual examination X 102 Examination of dimensions and mass X 206 Measu

17、rement of insulation resistance X Done during test EN 2591-314 Mated connectors 1 000 M 207 Voltage proof test X Done during test EN 2591-314 At low atmospheric Pressure: Method A, connectors mated, between size 5 triaxial contact and connector housing: 500 V r.m.s. 305 Rapid change of temperature X

18、 TA= (150+) C T0505+05B= ( 65 ) C t1= (30 ) min +306 Mould growth X Test conducted on materials Method A Duration: 28 days Growth: 0 307 Salt mist (see Table 1). 314 Immersion at low air pressure X Pressure 33 h Pa 315 Fluid resistance X 316 Ozone resistance X For types of fluids, number of cycles,

19、temperature and duration of immersion and temperature for the third phase: see Table 51 of EN 3682-001 317 Flammability X Method A 5 prEN 4530-006:20056 5 Designation EXAMPLE Description block SEALING SLEEVE Identity block EN4530-006A Number of this standard Permissible cable code (see Table 1) NOTE

20、 If necessary, the code I9005 shall be placed between the description block and the identify block. 6 Marking Not applicable 7 Delivery conditions The sealing sleeves are packaged and identified individually. Conditioning shall provide protection of the sealing sleeves against any eventual damage. Packaging shall include: the manufacturers name; the designation defined in 5; the manufacturers reference; the manufacturing date code (year week). 8 Technical specification See EN 4530-001.