ASD-STAN PREN 4531-005-2010 Aerospace series Connectors optical circular single and multipin coupled by threaded ring Flush contacts Part 005 Plug Product standard (Edition P 2).pdf

1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM prEN 4531-005 Edition P 2 December 2010 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONAvenue de Tervuren, 270 - B-1150 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.orgICS: 49.060 Supersedes

2、 edition P 1 of January 2005 and will supersede EN 4531-005:2007 Descriptors: Aerospace industry, aircraft, aircraft equipment, optical connector, elements of opticalconnection, optical contact, characteristics, test, quality assurance ENGLISH VERSION Aerospace series Connectors, optical, circular,

3、single and multipin, coupled by threaded ring Flush contacts Part 005: Plug Product standard Srie arospatiale Connecteurs optiques circulaires accouplement par bague filete Contacts affleurants Partie 005 : Fiche Norme de produit Luft- und Raumfahrt Optische Rundsteckverbinder mit Schraubkupplung Bn

4、dige Kontakte Teil 005: Stecker Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technic

5、ally approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After

6、 examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at nat

7、ional level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 31 December 2010 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2010 by

8、ASD-STAN prEN 4531-005:2010 (E) 2 Contents Page Foreword2 1 Scope 3 2 Normative references 3 3 Terms and definitions .3 4 Required characteristics.4 5 Marking .5 6 Technical specification .5 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After

9、 inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 4531-005:2010 (E) 3 1 Scope This standard specifies the characteristics of mounted plugs in the family of circular connecto

10、rs with triple start threaded coupling. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendme

11、nts) applies. EN 2424, Aerospace series Marking of aerospace products EN 4531-001, Aerospace series Connectors, optical, circular, single and multipin, coupled by threaded ring Flush contacts Part 001: Technical specification EN 4531-002, Aerospace series Connectors, optical, circular, single and mu

12、ltipin, coupled by threaded ring Flush contacts Part 002: Specification of performance and contact arrangements 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 4531-001 apply. prEN 4531-005:2010 (E) 4 4 Required characteristics 4.1 Dimensions and mass

13、es See Figure 1 and Table 1. Dimensions and tolerances are in millimetres. Key 1 Blue band Profile of coupling ring is not mandatory and is shown illustration purposes only. Figure 1 Table 1 B1 S Mass g classes Shell size 0,20 0 max. F, W, O K, S J, M, X A 09 18,40 21,80 26,5 61 19,5 66 11 21,10 25,

14、00 35 77 28 78 13 25,40 29,40 49 106 35 116 15 28.70 32.50 60 126 47 150 19 34,90 38,50 80 165 68 215 21 38,10 41,70 95 194 78 244 25 44,30 48,00 123 234 102 314 prEN 4531-005:2010 (E) 5 4.2 Material and surface treatment See EN 4531-002. 4.3 Optical, mechanical and climatic characteristics See EN 4

15、531-002. 5 Designation EXAMPLE Description block CONNECTOR, OPTICAL Identification block EN4531-5XXXXXX Number of the basic standard Plug Housing size (see EN 4531-002) Arrangement code (see EN 4531-002) Sleeve code (see EN 4531-002) Environmental class (see EN 4531-002) Polarization (see EN 4531-002) 6 Marking The marking shall include the identification defined in Clause 5, the date of manufacture (year, week) and the name or trade mark of the manufacturer or conform to standard EN 2424, code P, if required. 7 Technical specification See EN 4531-001.