ASD-STAN PREN 4626-001-2006 Aerospace series Connectors optical rectangular multicontact rack and panel Quadrax cavity 2 5 mm diameter ferrule Operating temperatures - 65 Degrees C.pdf

1、ASD STANDARD NORME ASD ASD NORM prEN 4626-001 Edition P 1 March 2006 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Gulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: Descriptors: Aerospace industry, aircraf

2、t, aircraft equipment, optical connector, elements of opticalconnection, optical contact, characteristics, test, quality assurance ENGLISH VERSION Aerospace series Connectors, optical, rectangular, multicontact, rack and panel, Quadrax cavity, 2,5 mm diameter ferrule Operating temperatures 65 C to 1

3、25 C (cable dependent) Flush contacts Part 001: Technical specification Srie arospatiale Connecteurs, optique, rectangulaire, contacts multiples, rackables, cavit Quadrax, frule diamtre 2,5 mm Temprature dutilisation 65 C 125 C (selon cble) Contacts affleurants Partie 001 : Spcification technique Lu

4、ft- und Raumfahrt Optische Rechtecksteckverbinder, Quadrax-Kontaktkammer, Durchmesser 2,5 mm Ferrule Betriebstemperaturen 65 C bis 125 C (vom Kabel abhngig) Bndige Kontakte Teil 001: Technische Lieferbedingungen This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-ST

5、AN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, t

6、he technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (

7、European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Ed

8、ition approved for publication 31 March 2006 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2006 by ASD-STAN prEN 4626-001:20062 Contents Page Foreword2 Introduction .3 1 Scope 3 2 Normative references 3 3 Terms and definitions .3 4 De

9、scription .4 5 Design .4 6 Drawings.5 7 Tests8 8 Quality assurance. 11 9 Designation and marking. 14 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-S

10、TANs General Process Manual, this standard has received approval for Publication. prEN 4626-001:2006 3 Introduction This family of fibre optic contact sub-assemblies are suitable for use in ARINC 600 connectors with size 8 Quadrax cavities in aerospace onboard applications. It provides easy access f

11、or optical contact end face cleaning. 1 Scope This standard specifies the general characteristics, the conditions for qualification, acceptance and quality assurance, as well as the test programs and groups for fibre sub-assembly contact in rack and panel connectors, intended for use in a temperatur

12、e range from 65 C to 125 C continuous (cable dependent). This standard specifies a pair of adaptors to fit with standard Quadrax cavities and EN 4531-101 optical contact. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated refer

13、ences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2591-100*, Aerospace series Elements of electrical and optical connection Test methods Part 100 : General. EN 3197, Aerospace series Installation of air

14、craft electrical and optical interconnection systems. 1)EN 4531-101, Aerospace series Connectors, optical, circular, single and multipin, coupled by threaded ring Flush contacts Part 101: Optical contact for EN C210A cable 55 C to 125 C Product standard. 1)EN 4626-002, Aerospace series Connectors, o

15、ptical, rectangular, multicontact, rack and panel, Quadrax cavity, 2,5 mm diameter ferrule Operating temperatures 65 C to 125 C (cable dependent) Flush contacts Part 002: Specification of performance and contact arrangements. 1)EN 9133, Aerospace series Quality management systems Qualification Proce

16、dure for aerospace standard parts. ARINC 600, Air transport avionics Equipment interfaces. 2)3 Terms and definitions For the purposes of this standard, the terms, definitions and abbreviations given in EN 2591-100 apply. *And all its parts quoted in this standard. 1) Published as ASD Prestandard at

17、the date of publication of this standard. 2) Published by: Aeronautical Radio, Inc. 2551 Riva road, Annapolis, Maryland 21401. prEN 4626-001:20064 4 Description 4.1 Optical sub-assembly and adaptor The optical sub-assembly comprises of an EN 4531-101 fibre optic contact, male and female adaptors all

18、owing positioning of the fibre optic contact in either a plug or receptacle Quadrax size 8 cavity, or a single part which integrates the EN 4531-101 contact and adaptor. The female adaptor is characterised by the integral alignment sleeve providing precise alignment of the optical ferrules. The opti

19、cal contact sub-assemblies are polarized by means of keyways in the adaptors and keys on the contact body. 4.2 Materials and surface treatment 4.2.1 Requirements When dissimilar metals are in close contact, adequate protection against corrosion shall be used for the electromotive force of the cell n

20、ot to exceed 0,25 V (see EN 3197). 4.2.2 Housing and inserts The connector housing and insert arrangement information are detailed in ARINC 600 standards. 4.2.3 Optical contacts Details of the optical contacts and alignment sleeves are detailed in EN 4531-101. 4.2.4 Adaptor The adaptor shall be of s

21、uitable material as specified in the product standard. 5 Design 5.1 Housing Connector housing is defined in the ARINC 600 standard. Quadrax cavity arrangements will be defined in Technical Report in preparation. 5.2 Optical contact See EN 4531-101. 5.3 Adaptor The adaptor is designed to provide mech

22、anical retention, and accurate alignment of the EN 4531-101 fibre optic contact within an ARINC 600 housing containing Quadrax size 8 cavities. The adaptor is keyed and mechanically retained in the ARINC 600 Quadrax size 8 insert cavity. The design permits installation of individual adaptors and con

23、tacts without removal of the connertor insert. Fitting ant removal of the adaptor will be from the rear of the connector insert using the tool specified in the relevant adaptor product standard. prEN 4626-001:20065 5.4 Connector and optical contact coupling sequence During normal coupling the mechan

24、ical properties of the connectors provide the following coupling sequence: Shells Polarizing keys Optical contacts Adaptor. Refer to the ARINC 600 specification for mechanical interconnecting requirements. 6 Drawings 6.1 Definition drawings The general intermateability dimensions of receptacles and

25、plugs are given below. Optical contact dimensions are defined in the product standard. 6.2 Coupling condition The stated dimensions are included to ensure that no mechanical interference occurs between the ferrule of the female adaptor and male adaptor body during the coupling cycle. See Figure 1. F

26、igure 1 prEN 4626-001:20066 6.3 Contact mating dimensions with male Quadrax insert (unmated position) See Figure 2. 5.07 0.247.20 0.34Figure 2 prEN 4626-001:20067 6.4 Optical contact mating dimensions with female Quadrax insert (unmated position) See Figure 3. 1.00 0.401.45 0.38Figure 3 prEN 4626-00

27、1:20068 6.5 Displacement of the optical contact in the connector (mated position) See Figure 4. 5.43 1.21Figure 4 7 Tests 7.1 Tests according to EN 2591-100 standard The tests of EN 2591-100, applicable in the context of this standard as well as the details necessary for implementing them and for in

28、specting connector characteristics, are given in Table 1. prEN 4626-001:2006 9 Table 1 EN 2591- Designation of the test Details 6101 Visual examination No loosening of parts, cracks, excessive wear, or detached parts. Optical face undamaged and free from contamination when examined at 100 magnificat

29、ion minimum. 101 Visual examination Not applicable 102 Examination of dimensions and mass According to clause 6 and product standard. NOTE In the case of a qualified inspection system, the parts unrelated to a production batch, may be used. 6301 Endurance at temperature For performance and test meth

30、od requirements refer to the applicable product standard for the component and cable under test. 302 Climatic sequence Not applicable (already cover by EN 4531-101) 6303 Cold/low pressure and damp heat Not applicable (already cover by EN 4531-101) 304 Damp heat steady state Not applicable 6305 Rapid

31、 change of temperature For performance and test method requirements refer to the applicable product standard for the component and cable under test. 6306 Mould growth Not applicable 6307 Salt mist 48 hours 308 Sand and dust Not applicable 309 Dry heat Not applicable 310 Cold Not applicable 311 Low a

32、ir pressure Not applicable 312 Air leakage Not applicable 313 Driving rain (artificial) Not applicable 6314 Immersion at low air pressure Not applicable 6315 Fluid resistance Not applicable (already cover by EN 4531-101) 6316 Ozone resistance Not applicable 6317 Flammability Not applicable 6318 Fire

33、 resistance Not applicable 319 Gastightness of solderless wrapped connections Not applicable 320 Simulated solar radiation at ground level Not applicable 6321 Damp heat, cyclic test For performance and test method requirements refer to the applicable product standard for the component and cable unde

34、r test (in place of test EN 2591-304) 6323 Thermal shock (Hermetically sealed devices) Not applicable continued prEN 4626-001:200610 Table 1 (continued) EN 2591- Designation of the test Details 6324 Interfacial sealing Not applicable 325 Ice resistance Not applicable 6401 Acceleration steady state N

35、ot applicable 6402 Shock Method A, severity 50, 11 ms. 6403 Vibrations Method B, Figure 3, Table 2, level E. Two axes (X and Y), 8 hours/axe (checked with ARINC 600). 6404 Transverse load Not applicable 6405 Axial load Not applicable 6406 Mechanical endurance 500 cycles for connector Subclause 7.2 A

36、dditional test: optical maintenance ageing: 10 cycles. 407 Durability of contact retention system and seals Not applicable 408 Mating and unmating forces Any configuration of layout must not exceed the maximum value defined in ARINC 600 specification for mating force. 409 Contact retention in insert

37、 Not applicable 410 Insert retention in housing (axial) Not applicable 411 Insert retention in housing (torsional) Not applicable 412 Contact insertion and extraction forces Not applicable 6414 Unmating of lanyard release optical connection elements Not applicable 6415 Test probe damage Not applicab

38、le 427 Robustness of protective cover attachment Not applicable 601 Insertion loss For performance and test method requirements refer to the applicable product standard for the component and cable under test. 602 Variation of attenuation and optical discontinuity For performance and test method requ

39、irements refer to the applicable product standard for the component and cable under test. 603 Change of power distribution Not applicable 604 Cleaning capability of optical face For performance and test method requirements refer to the applicable product standard for the component and cable under te

40、st. 605 Return loss For performance and test method requirements refer to the applicable product standard for the component and cable under test. continued prEN 4626-001:2006 11 Table 1 (concluded) EN 2591- Designation of the test Details 607 Immunity to ambient light coupling Not applicable 609 Eff

41、ectiveness of cable attachment - Cable cyclic flexing Not applicable 610 Effectiveness of cable attachment - Cable pulling Not applicable 611 Effectiveness of cable attachment - Cable torsion Not applicable 612 Effectiveness of cable attachment - Cable axial compression Not applicable 613 Impact tes

42、t Not applicable 614 Connector radial compression Not applicable 615 Connection integrity at temperature Not applicable (cover by test EN 2591-6301) 617 Temperature cycling Not applicable (cover by test EN 2591-6305) 7.2 Additional test Maintenance ageing: One cycle is defined as the insertion and e

43、xtraction of the contact in the adaptor. No cleaning is required during this test. 8 Quality assurance 8.1 General Quality assurance shall conform to EN 9133. 8.2 Qualification 8.2.1 General Qualification of a product (see EN 4626-002) shall be attained: a) by using a qualified EN 4531-101 optical c

44、ontact, or; b) either when the specimens as defined in 8.2.2 have satisfied the applicable tests in groups 0 to 2, or; c) extension of qualification i.e. qualification of a model very similar to a model already qualified. Qualification may be obtained by performing a small number of additional tests

45、 or by analogy of structural similarity. prEN 4626-001:200612 8.2.2 Sampling and definition of specimens Three samples per group. Definition of specimen shall be in accordance with EN 4626-002. All the samples shall pass the group 0. 8.2.3 Preparation of specimens All specimens shall be terminated,

46、using typically 4 m length of cable, i.e. each half of a connector shall have a 2 m minimum length of cable attached. 8.2.4 Programme of qualification tests The qualification approval tests are defined in Table 1 and shall be carried out in the sequence specified in Table 2. Table 2 Performance veri

47、fication test Tests EN 2591- Remarks Group 0 Examination of dimensions and mass 102 Conformance to clause 6 and product standard Insertion loss 601 After termination Return loss 605 Visual examination 6101 Mating and unmating forces 408 Method A Insertion loss 601 Visual examination 6101 Group 1 Rap

48、id change of temperature 6305 Insertion loss as EN 2591-601. Visual examination as EN 2591-6101. Mechanical endurance 6406 Variation of insertion loss as EN 2591-601. Overtightening not required. Visual examination as EN 2591-6101. Cleaning capability of optical face 604 Vibrations 6403 Optical disc

49、ontinuity as EN 2591-602. Insertion loss as EN 2591-601. Shock 6402 Optical discontinuity as EN 2591-602. Insertion loss as EN 2591-601. Mating and uncoupling torque as EN 2591-408, Method A. Overtightening not required. Visual examination as EN 2591-6101. Mating and unmating forces 408 Method A. Visual examination 6101 continued prEN 4626-001:2006 13 Table 2 Performance verification test (concluded) Tests EN 2591- Remarks Group 2 Endurance at temperature 6301 Insertion loss as EN 2591-601. Sal