ASD-STAN PREN 4640-003-2007 Aerospace series Connectors optical rectangular rack and panel multicontact 1 25 diameter ferrule with removable alignment sleeve holder Part 003 Plug o.pdf

1、ASD STANDARD NORME ASD ASD NORM prEN 4640-003 Edition P 1 February 2007 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Gulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: 49.060 Descriptors: ENGLISH VERSION A

2、erospace series Connectors, optical, rectangular, rack and panel, multicontact, 1,25 diameter ferrule, with removable alignment sleeve holder Part 003: Plug optical connector Product standard Srie arospatiale Connecteurs, optiques, rectangulaires, contacts multiples, rackables, frule diamtre 1,25, q

3、uips dun porte sleeve dmontable Partie 003 : Fiche de connecteur optique Norme de produit Luft- und Raumfahrt Optischer Rechtecksteckverbinder, Gehuse, Einschub, Steckverbinder, Multipin, Ferrulendurchmesser 1,25 mm, demontierbarer Zentrierhlsenhalter Teil 003: Optischer Stecker Produktnorm This “Ae

4、rospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain

5、 following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreemen

6、t of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a nationa

7、l standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 28 February 2007 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2007 by ASD-STAN prEN 4640-003:20072 Contents Page Foreword2

8、 1 Scope 3 2 Normative references 3 3 Terms and definitions .3 4 Required characteristics.3 5 Designation 4 6 Marking .5 7 Technical specification .5 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accor

9、dance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 4640-003:20073 1 Scope This standard specifies the characteristics of a plug optical connectors, rectangular, rack and panel, multicontact. 2 Normative references T

10、he following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2424, Aerospace series Marking of aerospace pro

11、ducts. EN 4640-001, Aerospace series Connectors, optical, rectangular, rack and panel, multicontact, 1,25 diameter ferrule, with removable alignment sleeve holder Part 001: Technical specification.1)EN 4640-002, Aerospace series Connectors, optical, rectangular, rack and panel, multicontact, 1,25 di

12、ameter ferrule, with removable alignment sleeve holder Part 002: List of product standards. 1)ARINC Specification 600, Air Transport Avionics Equipment Interfaces. 2)3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 4640-001 apply. 4 Required characteri

13、stics 4.1 Dimensions 4.1.1 Plug connector: Outer dimensions See ARINC Specification 600. 4.1.2 Plug connector: Optical contact position See Figure 1. 1) Published as ASD Prestandard at the date of publication of this standard. 2) Published by: AERONAUTICAL RADIO, INC. 2551 Riva road, Annapolis, Mary

14、land 21401-7435 USA. prEN 4640-003:20074 Key 1 Mechanical bottom of the plug 2 39 max. with grommet NOTE Other dimensions in accordance with ARINC 600. Figure 1 4.2 Material and surface treatment See ARINC Specification 600. 4.3 Optical, mechanical and climatic characteristics See EN 4640-002. 5 Des

15、ignation EXAMPLE Description block CONNECTOR, OPTICAL Identity block EN4640-003F36 Number of the basic standard Plug Arrangement code (see EN 4640 002) prEN 4640-003:20075 6 Marking The marking shall include the identification, the date of manufacture (year, week) and the name or trade mark of the manufacturer or conform to standard EN 2424, code P, if required. 7 Technical specification See optical contact product standard. 3)3) Performance is directly linked to optical contact and fibre technology.