1、ASD STANDARD NORME ASD ASD NORM prEN 4800-001 Edition P 2 September 2009 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONAvenue de Tervuren, 270 - B-1150 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 775 8131 - www.asd-stan.orgICS: Supersedes edition P 1 of D
2、ecember 2002 Descriptors: ENGLISH VERSION Aerospace series Titanium and titanium alloys Technical specification Part 001: Plate, sheet and strip Srie arospatiale Titane et alliages de titane Spcification technique Partie 001 : Plaques, tles et bandes Luft- und Raumfahrt Titan und Titanlegierungen Kn
3、eterzeugnisse Technische Lieferbedingungen Teil 001: Platten, Bleche This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Indu
4、stry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identificati
5、on of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then t
6、o implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 30 September 2009 Comments should be sent within six months after the date of publication to ASD-STAN Metallic M
7、aterial Domain Copyright 2009 by ASD-STAN prEN 4800-001:2009 (E) 2 Contents Page Foreword2 Introduction .3 1 Scope 3 2 Normative references 3 3 Terms and definitions .5 4 Wording of order5 5 Health and safety .5 6 Technical requirements 5 Foreword This standard was reviewed by the Domain Technical C
8、oordinator of ASD-STANs Metallic Material Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 4800-001:2009 (E) 3 Introduction This standard is part of the series
9、 of EN metallic material standards for aerospace applications. The general organization of this series is described in EN 4258. 1 Scope This standard defines the requirements for the ordering, manufacture, testing, inspection and delivery of titanium and titanium alloy plate, sheet and strip. It sha
10、ll be applied when referred to and in conjunction with the EN material standard unless otherwise specified on the drawing, order or inspection schedule. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the ed
11、ition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 4288, Geometrical Product Specifications (GPS) Surface texture: Profile method Rules and Procedures for the Assessment of surface texture EN 2002-001, Aerospace series M
12、etallic materials Test methods Part 001: Tensile testing at ambient temperature EN 2002-002, Aerospace series Metallic materials Test methods Part 002: Tensile testing at elevated temperature EN 2002-005, Aerospace series Metallic materials Test methods Part 005: Uninterrupted creep and stress-ruptu
13、re testing EN 2002-6, Aerospace series Test methods for metallic materials Part 6: Bend testing1)EN 2002-8, Aerospace series Metallic materials Test methods Part 8: Micrographic determination of grain size1)EN 2003-009, Aerospace series Test methods Titanium and titanium alloys Part 009: Determinati
14、on of surface contamination EN 2032-1, Aerospace series Metallic materials Part 1: Conventional designation. EN 2032-2, Aerospace series Metallic materials Part 2: Coding of metallurgical condition in delivery condition. EN 2078, Aerospace series Metallic materials Manufacturing schedule, inspection
15、 schedule, inspection and test report Definition, general principles, preparation and approval. EN 2955, Aerospace series Recycling of titanium and titanium alloy scrap. EN 3114-001, Aerospace series Test method Microstructure of ( + ) titanium alloy wrought products Part 001: General requirements 1
16、) Published as ASD Prestandard at the date of publication of this standard. prEN 4800-001:2009 (E) 4 EN 3114-003, Aerospace series Test method Microstructure of ( + ) titanium alloy wrought products Part 003: Microstructure of plate EN 3114-004, Aerospace series Test method Microstructure of ( + ) t
17、itanium alloy wrought products Part 004: Microstructure of sheet for superplastic forming EN 3683, Aerospace series Test method Titanium alloy wrought products Determination of primary alpha content Point count method and line intercept method EN 3684, Aerospace series Test method Titanium alloy wro
18、ught products Determination of beta transus temperature Metallographic method EN 3873, Aerospace series Test method Crack propagation test 2)EN 3874, Aerospace series Test method for metallic materials Constant amplitude force-controlled low cycle fatigue testing1)EN 3976, Aerospace series Titanium
19、and titanium alloys Test method Chemical analysis for the determination of hydrogen content EN 3987, Aerospace series Test method for metallic materials Constant amplitude force-controlled high cycle fatigue testing1)EN 3988, Aerospace series Test method for metallic materials Constant amplitude str
20、ain-controlled low cycle fatigue testing1)EN 4050-1, Aerospace series Test method for metallic materials Ultrasonic inspection of bars, plates, forging stock and forgings Part 1: General requirement1)EN 4050-4, Aerospace series Test method for metallic materials Ultrasonic inspection of bars, plates
21、, forging stock and forgings Part 4: Acceptance criteria1)EN 4258, Aerospace series Metallic materials General organization of standardization Links between types of EN standards and their use EN 4259, Aerospace series Metallic materials Definition of general terms1)EN 9100, Aerospace series Quality
22、 management systems Requirements (based on ISO 9001:2000) and Quality systems Model for quality assurance in design, development, production, installation and servicing (based on ISO 9001:1994). TR 2410, Aerospace series Metallic materials Relationship between dimensional standards and material stan
23、dards3)AMS 2750, Pyrometry 4)ASTM E 399, Standard test method for linear-elastic plane-strain fracture toughness k/c of metallic materials 4)2) In preraration at the date of publication of this standard. 3) Published as an ASD Technical Report at the date of publication of this standard. 4) Publishe
24、d by: American Society for Testing and Materials (ASTM), 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA, 19428-2959 USA. prEN 4800-001:2009 (E) 5 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 4259 apply. 4 Wording of order The order shall
25、 clearly indicate: quantities to be supplied; dates of delivery; material standard number; delivery condition and metallurgical code of products; dimensions and tolerances or reference to an appropriate dimensional standard; product designation, when required; forwarding address; nature and type of
26、packing, if required; definition and frequency of any special tests and their retest procedures, if required. 5 Health and safety The product in the delivery condition shall fulfil the current health and safety laws of the area of the country when and where it is to be delivered. A product safety da
27、ta sheet shall be available. 6 Technical requirements 6.1 General The product shall be manufactured in accordance with the requirements of the relevant material standard and the applicable requirements of this specification. A manufacturing schedule shall be established and applied in accordance wit
28、h EN 2078. Product shall satisfy the requirements of the material standard and/or order and shall be free from irregularities prejudicial to the subsequent manufacture or use of this product. Not with standing previous acceptance complying with this material standard, any product that is found, at a
29、 later stage, to contain such defects shall be rejected. Unless otherwise specified, the requirements in Tables 1 and 2 shall apply in conjunction with those of the relevant material standard. Table 1 relates to lines 1 to 29 (inclusive) of the material standard and Table 2 relates to lines 30 onwar
30、ds in which the sub-line format is also used. Lines 2 to 98 may also be opened in line 100 if the material standard details specific qualification requirements. If a specific line number is not shown in Tables 1 and 2, the requirement is stated in the material standard and/or order. The requirements
31、 of the order and/or material standard shall over-ride the requirements of the technical specification. prEN 4800-001:2009 (E) 6 6.2 Qualification requirements Qualification requirements when invoked by the material standard and/or order are detailed in Tables 1 and 2. Unless otherwise agreed betwee
32、n the manufacturer and purchaser the qualification phase shall be run on the first 3 batches coming from 3 ingots. 6.3 Release requirements 6.3.1 Release tests Release testing shall be the responsibility of the manufacturer. The purchaser reserves the right to perform any of the inspections and/or t
33、ests required by the material standard and/or order. The test samples shall be representative of the product. When required the manufacturer shall inform the purchaser of the planned dates for extraction of samples and release testing in order that these operations may be witnessed. Tables 1 and 2 d
34、etail the requirements for each line of the material standard. Unless otherwise specifically requested by the purchaser, a particular inspection and/or test for release shall be carried out if corresponding acceptance criteria and/or values are stated in the applicable material standard, but see als
35、o in 6.3.5. 6.3.2 Retests If the test procedure or test piece preparation is faulty, testing shall be re-applied at the original frequency after rectification of the original cause of failure. When failure cannot be attributed to faulty testing, or test piece preparation, further test samples shall
36、be selected at twice the original frequency from the product, one of which shall be that on which the original results were obtained unless already withdrawn by the manufacturer after suitable identification of the cause of failure. If all retest results are satisfactory, the batch shall be accepted
37、. If one or more tests are unsatisfactory, the batch shall be: rejected, or 100 % retested and the conforming products accepted, or partially or fully re-heat treated if heat treatment can rectify the cause of the failure and tested as a completely new batch except for chemical composition, for whic
38、h redetermination of hydrogen content is required. No product or test sample shall be re-heat treated more than twice 6.3.3 Rejection Any failure to meet the requirements of the material standard shall be cause for rejection. 6.3.4 Special tests Special tests may be required by the purchaser. In suc
39、h cases, the nature of the test, method, frequency and technical requirements shall be specified on the order or inspection schedule and shall be mutually agreed by the manufacturer and purchaser. 6.3.5 Capability clause Where this is invoked and where sufficient evidence exists, the test shall not
40、be carried out (unless specifically requested by the purchaser). However, this in no way reduces the obligations of the manufacturer to fulfil the requirements. If subsequent testing indicates that the product does not comply with the requirements, the batch shall be rejected. prEN 4800-001:2009 (E)
41、 7 If sufficient statistical evidence does not exist, the test shall be carried out at a frequency agreed between the manufacturer and the purchaser. 6.3.6 Statistical process control Reduction in the extent of release testing, other than that defined in 6.3.5 above, may be negotiated with the purch
42、aser on the basis of appropriate statistical process control and/or statistical data. 6.3.7 Inspection and test report The manufacturer shall furnish, with each delivery, a report conforming to the requirements of EN 2078 stating the following: manufacturers name and address and, if appropriate, ide
43、ntification of the plant; order number; material standard number; method of melting; delivery condition and metallurgical code of the product; quantity and dimensions; manufacturing and inspection schedule reference; cast and batch number; batch and/or test samples heat treatment condition; results
44、of the tests and retests if any. 6.4 Traceability Each product shall be traceable to the cast, production batch and/or heat treatment batch at all stages of manufacture, testing and delivery. prEN 4800-001:2009 (E) 8 Table 1 Technical requirements for lines 1 to 29, where appropriate Frequency of te
45、sting Material standard line reference No. Title Requirements Qualification Release 1 Material designation See EN 2032-1. 2 Chemical composition The test samples used for chemical analysis shall be representative of the product and shall be taken from location corresponding to top and bottom of each
46、 ingot produced after the final melting stage. The method of chemical analysis shall be at the discretion of the manufacturer unless otherwise stated in the material standard or order. In cases of dispute, the method of chemical analysis shall be agreed between the manufacturer and purchaser prefera
47、bly using existing chemical analysis. 2 per cast 2 per cast Specific requirements for hydrogen content: The hydrogen content shall be determined on each batch in the delivery condition in accordance with EN 3976. 1 per batch 1 per batch 3 Method of melting Method of melting consists of multiple melt
48、 using combination of non-consumable electrode, consumable electrode and cold hearth (electron beam or plasma arc) melting practices. Some of the following requirements are dependent on the actual melting route non-consumable electrode melting should be used for consolidation purpose only. 1 Raw mat
49、erial: Raw materials shall be purchased only from suppliers approved by the manufacturer and registered in his list of approved suppliers. Approval of suppliers shall be made in accordance with written procedures contained within the quality assurance system of the manufacturer. Titanium sponge and alloying elements: The requirements shall be specified by the manufacturer who shall also esta
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1