1、ASD STANDARD NORME ASD ASD NORM prEN 4800-002 Edition P 2 September 2009 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONAvenue de Tervuren, 270 - B-1150 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 775 8131 - www.asd-stan.orgICS: Supersedes edition P 1 of A
2、pril 2002 Descriptors: ENGLISH VERSION Aerospace series Titanium and titanium alloys Technical specification Part 002: Bar and section Srie arospatiale Titane et alliages de titane Spcification technique Partie 002 : Barres et profils Luft- und Raumfahrt Titan und Titanlegierungen Kneterzeugnisse Te
3、chnische Lieferbedingungen Teil 002: Stange, und Profile This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has
4、 been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the st
5、andard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement
6、the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 30 September 2009 Comments should be sent within six months after the date of publication to ASD-STAN Metallic Material Doma
7、in Copyright 2009 by ASD-STAN prEN 4800-002:2009 (E) 2 Contents Page Foreword2 Introduction .3 1 Scope 3 2 Normative references 3 3 Terms and definitions .5 4 Wording of order5 5 Health and safety .5 6 Technical requirements 5 Foreword This standard was reviewed by the Domain Technical Coordinator o
8、f ASD-STANs Metallic Material Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 4800-002:2009 (E) 3 Introduction This standard is part of the series of EN metal
9、lic material standards for aerospace applications. The general organization of this series is described in EN 4258. 1 Scope This standard defines the requirements for the ordering, manufacture, testing, inspection and delivery of titanium and titanium alloy bar and section. It shall be applied when
10、referred to and in conjunction with the EN material standard unless otherwise specified on the drawing, order or inspection schedule. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies
11、. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2002-001, Aerospace series Metallic materials Test methods Part 001: Tensile testing at ambient temperature EN 2002-002, Aerospace series Metallic materials Test methods Part 002: Tensile t
12、esting at elevated temperature EN 2002-005, Aerospace series Metallic materials Test methods Part 005: Uninterrupted creep and stress-rupture testing EN 2002-8, Aerospace series Metallic materials Test methods Part 8: Micrographic determination of grain size 1)EN 2002-16, Aerospace series Metallic m
13、aterials Test methods Part 16: Non-destructive testing Penetrant testing 1)EN 2003-009, Aerospace series Test methods Titanium and titanium alloys Part 009: Determination of surface contamination EN 2032-1, Aerospace series Metallic materials Part 1: Conventional designation EN 2032-2, Aerospace ser
14、ies Metallic materials Part 2: Coding of metallurgical condition in delivery condition EN 2078, Aerospace series Metallic materials Manufacturing schedule, inspection schedule, inspection and test report Definition, general principles, preparation and approval EN 2954-002, Aerospace series Macrostru
15、ctural examination of titanium and titanium alloy wrought products Part 002: Macrostructure of bar, section, forging stock and forgings 1)EN 2955, Aerospace series Recycling of titanium and titanium alloy scrap EN 3114-001, Aerospace series Test method Microstructure of ( + ) titanium alloy wrought
16、products Part 001: General requirements 1) Published as ASD Prestandard at the date of publication of this standard. prEN 4800-002:2009 (E) 4 EN 3114-002, Aerospace series Test method Microstructure of ( + ) titanium alloy wrought products Part 002: Microtructure of bars, sections, forging stock and
17、 forgings EN 3238, Aerospace series Test methods for metallic materials Shear test for rivet wires and rivets in metallic material except aluminium and aluminium alloys2)EN 3683, Aerospace series Test method Titanium alloy wrought products Determination of primary content Point count method and line
18、 intercept method EN 3684, Aerospace series Test method Titanium alloy wrought products Determination of transus temperature Metallographic method EN 3874, Aerospace series Test method for metallic materials Constant amplitude force-controlled low cycle fatigue testing1)EN 3976, Aerospace series Tit
19、anium and titanium alloys Test method Chemical analysis for the determination of hydrogen content EN 3987, Aerospace series Test method for metallic materials Constant amplitude force-controlled high cycle fatigue testing 1)EN 3988, Aerospace series Test method for metallic materials Constant amplit
20、ude strain-controlled low cycle fatigue testing 1)EN 4050-1, Aerospace series Test method for metallic materials Ultrasonic inspection of bars, plates, forging stock and forgings Part 1: General requirement 1)EN 4050-4, Aerospace series Test method for metallic materials Ultrasonic inspection of bar
21、s, plates, forging stock and forgings Part 4: Acceptance criteria 1)EN 4258, Aerospace series Metallic materials General organization of standardization Links between types of EN standards and their use EN 4259, Aerospace series Metallic materials Definition of general terms 1)EN 9100, Aerospace ser
22、ies Quality management systems Requirements (based on ISO 9001:2000) and Quality systems Model for quality assurance in design, development, production, installation and servicing (based on ISO 9001:1994) EN 9133, Aerospace series Quality management systems Qualification procedure for aerospace stan
23、dard parts TR 2410, Aerospace series Metallic materials Relationship between dimensional standards and material standards 3)AMS 2750, Pyrometry 4)ASTM E 399, Standard test method for linear-elastic plane-strain fracture toughness k/c of metallic materials 4)2) In preraration at the date of publicati
24、on of this standard. 3) Published as an ASD Technical Report at the date of publication of this standard. 4) Published by: American Society for Testing and Materials (ASTM), 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA, 19428-2959 USA. prEN 4800-002:2009 (E) 5 3 Terms and definitions Fo
25、r the purposes of this document, the terms and definitions given in EN 4259 apply. 4 Wording of order The order shall clearly indicate: quantities to be supplied; dates of delivery; material standard number; delivery condition and metallurgical code of products; dimensions and tolerances or referenc
26、e to an appropriate dimensional standard; product designation, when required; forwarding address; nature and type of packing, if required; definition and frequency of any special tests and their retest procedures, if required. 5 Health and safety The products in the delivery condition shall fulfil t
27、he health and safety laws of the area of the country when and where it is to be delivered. A product safety data sheet shall be available. 6 Technical requirements 6.1 General The product shall be manufactured in accordance with the requirements of the relevant material standard and the applicable r
28、equirements of this specification. A manufacturing schedule shall be established and applied in accordance with EN 2078. Product shall satisfy the requirements of the material standard and/or order and shall be free from irregularities prejudicial to the subsequent manufacture or use of this product
29、. Not with standing previous acceptance complying with this material standard, any product that is found, at a later stage, to contain such defects shall be rejected. Unless otherwise specified, the requirements in Tables 1 and 2 shall apply in conjunction with those of the relevant material standar
30、d. Table 1 relates to lines 1 to 29 (inclusive) of the material standard and Table 2 relates to lines 30 onwards in which the sub-line format is also used. Lines 2 to 98 may also be opened in line 100 if the material standard details specific qualification requirements. If a specific line number is
31、not shown in Tables 1 and 2, the requirement is stated in the material standard and/or order. The requirements of the order and/or material standard shall over-ride the requirements of the technical specification. prEN 4800-002:2009 (E) 6 6.2 Qualification requirements Qualification requirements whe
32、n invoked by the material standard and/or order are detailed in Tables 1 and 2. Unless otherwise agreed between the manufacturer and purchaser the qualification phase shall be run on the first 3 batches, coming from 3 different ingots. 6.3 Release requirements 6.3.1 Release tests Release testing sha
33、ll be the responsibility of the manufacturer. The purchaser reserves the right to perform any of the inspections and/or tests required by the material standard and/or order. The test samples shall be representative of the product. When required the manufacturer shall inform the purchaser of the plan
34、ned dates for extraction of samples and release testing in order that these operations may be witnessed. Tables 1 and 2 detail the requirements for each line of the material standard. Unless otherwise specifically requested by the purchaser, a particular inspection and/or test for release shall be c
35、arried out if corresponding acceptance criteria and/or values are stated in the applicable material standard, but see also in 6.3.5. 6.3.2 Retests If the test procedure or test piece preparation is faulty, testing shall be re-applied at the original frequency after rectification of the original caus
36、e of failure. When failure cannot be attributed to faulty testing, or test piece preparation, further test samples shall be selected at twice the original frequency from the product, one of which shall be that on which the original results were obtained unless already withdrawn by the manufacturer a
37、fter suitable identification of the cause of failure. If all retest results are satisfactory, the batch shall be accepted. If one or more tests are unsatisfactory, the batch shall be: rejected, or 100 % retested and the conforming products accepted, or partially or fully re-heat treated if heat trea
38、tment can rectify the cause of the failure and tested as a completely new batch except for chemical composition, for which redetermination of hydrogen content is required. No product or test sample shall be re-heat treated more than twice 6.3.3 Rejection Any failure to meet the requirements of the m
39、aterial standard shall be cause for rejection. 6.3.4 Special tests Special tests may be required by the purchaser. In such cases, the nature of the test, method, frequency and technical requirements shall be specified on the order or inspection schedule and shall be mutually agreed by the manufactur
40、er and purchaser. 6.3.5 Capability clause Where capability clause is invoked and where sufficient statistical evidence exists, the test shall not be carried out (unless specifically requested by the purchaser). However, this in no way reduces the obligations of the manufacturer to fulfil the require
41、ments. If subsequent testing indicates that the product does not comply with the requirements, the batch shall be rejected. prEN 4800-002:2009 (E) 7 If sufficient statistical evidence does not exist, the test shall be carried out at a frequency agreed between the manufacturer and the purchaser. 6.3.
42、6 Statistical process control Reduction in the extent of release testing, other than that defined in 6.3.5 above, may be negotiated with the purchaser on the basis of appropriate statistical process control and/or statistical data. 6.3.7 Inspection and test report The manufacturer shall furnish, wit
43、h each delivery, a report conforming to the requirements of EN 2078 stating the following: manufacturers name and address and, if appropriate, identification of the plant; order number; material standard number; delivery condition and metallurgical code of the product; quantity and dimensions; manuf
44、acturing and inspection schedule reference; cast and batch number; batch and/or test samples heat treatment condition; results of the tests and retests if any. 6.4 Traceability Each product shall be traceable to the cast, production batch and/or heat treatment batch at all stages of manufacture, tes
45、ting and delivery. prEN 4800-002:2009 (E) 8 Table 1 Technical requirements for lines 1 to 29, where appropriate Frequency of testing Material standard line reference No Title Requirements Qualification Release 1 Material designation See EN 2032-1. The test samples used for chemical analysis shall be
46、 representative of the product and shall be taken from location corresponding to top and bottom of each ingot produced after the final melting stage. The method of chemical analysis shall be at the discretion of the manufacturer unless otherwise stated in the material standard or order. In cases of
47、dispute, the method of chemical analysis shall be agreed between the manufacturer and purchaser preferably using existing chemical analysis standards. The measured chemical composition shall be stated on the inspection certificate. 2 per cast 2 per cast 2 Chemical composition Specific requirements f
48、or hydrogen content: The hydrogen content shall be determined on each batch in the delivery condition in accordance with EN 3976. 1 per batch 1 per batch 3 Method of melting Method of melting consists of multiple melt using combination of non-consumable electrode, consumable electrode and cold heart
49、h (electron beam or plasma arc) melting practices. Some of the following requirements are dependent on the actual melting route non-consumable electrode melting should be used for consolidation purpose only. 1 Raw material: Raw materials shall be purchased only from suppliers approved by the manufacturer and registered in his list of approved suppliers. Approval of suppliers shall be made
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1