1、ASD STANDARD NORME ASD ASD NORM prEN 4800-003 Edition P 2 September 2009 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONAvenue de Tervuren, 270 - B-1150 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 775 8131 - www.asd-stan.orgICS: Supersedes edition P 1 of A
2、pril 2002 Descriptors: ENGLISH VERSION Aerospace series Titanium and titanium alloys Technical specification Part 003: Tube Srie arospatiale Titane et alliages de titane Spcification technique Partie 003 : Tubes Luft- und Raumfahrt Titan und Titanlegierungen Kneterzeugnisse Technische Lieferbedingun
3、gen Teil 003: Rohre This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the exp
4、erts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review
5、by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving th
6、e EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 30 September 2009 Comments should be sent within six months after the date of publication to ASD-STAN Metallic Material Domain Copyright 2009 by ASD-STAN prEN 48
7、00-003:2009 (E) 2 Contents Page Foreword2 Introduction .3 1 Scope 3 2 Normative references 3 3 Terms and definitions .4 4 Wording of order4 5 Health and safety .5 6 Technical requirements 5 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Metallic Material Domain.
8、 After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 4800-003:2009 (E) 3 Introduction This standard is part of the series of EN metallic material standards for aerospace
9、applications. The general organization of this series is described in EN 4258. 1 Scope This standard defines the requirements for the ordering, manufacture, testing, inspection and delivery of titanium and titanium alloy tube. It shall be applied when referred to and in conjunction with the EN mater
10、ial standard unless otherwise specified on the drawing, order or inspection schedule. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of
11、the referenced document (including any amendments) applies. ISO 6772, Aerospace Fluid systems Impulse testing of hydraulic hose, tubing and fitting assemblies EN 2002-001, Aerospace series Metallic materials Test methods Part 001: Tensile testing at ambient temperature EN 2002-002, Aerospace series
12、Metallic materials Test methods Part 002: Tensile testing at elevated temperature EN 2002-8, Aerospace series Metallic materials Test methods Part 8: Micrographic determination of grain size 1)EN 2002-17, Aerospace series Test methods for metallic materials Tube used under pressure Part 17: Non-dest
13、ructive testing Integrity test 1)EN 2002-18, Aerospace series Test methods for metallic materials Part 18: Hydraulic distension test for tube 1)EN 2002-20, Aerospace series Test methods for metallic materials Part 20: Eddy current testing of circular cross-section tubes 1)EN 2003-009, Aerospace seri
14、es Test methods Titanium and titanium alloys Part 009: Determination of surface contamination EN 2032-1, Aerospace series Metallic materials Part 1: Conventional designation EN 2032-2, Aerospace series Metallic materials Part 2: Coding of metallurgical condition in delivery condition EN 2078, Aerosp
15、ace series Metallic materials Manufacturing schedule, inspection schedule, inspection and test report Definition, general principles, preparation and approval EN 2955, Aerospace series Recycling of titanium and titanium alloy scrap 1) Published as ASD Prestandard at the date of publication of this s
16、tandard. prEN 4800-003:2009 (E) 4 EN 3114-001, Aerospace series Test method Microstructure of ( + ) titanium alloy wrought products Part 001: General requirements EN 3684, Aerospace series Test method Titanium alloy wrought products Determination of transus temperature Metallographic method EN 3718,
17、 Aerospace series Test method for metallic materials Ultrasonic inspection of tubes EN 3976, Aerospace series Titanium and titanium alloys Test method Chemical analysis for the determination of hydrogen content EN 4258, Aerospace series Metallic materials General organization of standardization Link
18、s between types of EN standards and their use EN 4259, Aerospace series Metallic materials Definition of general terms 1)EN 9100, Aerospace series Quality management systems Requirements (based on ISO 9001:2000) and Quality systems Model for quality assurance in design, development, production, inst
19、allation and servicing (based on ISO 9001:1994) EN 9133, Aerospace series Quality management systems Qualification procedure for aerospace standard parts EN ISO 8492, Metallic materials Tube Flattening test EN ISO 8493, Metallic materials Tube Drift expanding test TR 2410, Aerospace series Metallic
20、materials Relationship between dimensional standards and material standards 2)AMS 2750, Pyrometry 3)3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 4259 apply. 4 Wording of order The order shall clearly indicate: quantities to be supplied; dates of de
21、livery; material standard number; delivery condition and metallurgical code of products; 2) Published as an ASD Technical Report at the date of publication of this standard. 3) Published by: American Society for Testing and Materials (ASTM), 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA,
22、 19428-2959 USA. prEN 4800-003:2009 (E) 5 dimensions and tolerances or reference to an appropriate dimensional standard; product designation, when required; forwarding address; nature and type of packing, if required. 5 Health and safety The products in the delivery condition shall fulfil the health
23、 and safety laws of the area of the country when and where it is to be delivered. A product safety data sheet shall be available. 6 Technical requirements 6.1 General The product shall be manufactured in accordance with the requirements of the relevant material standard and the applicable requiremen
24、ts of this specification. A manufacturing schedule shall be established and applied in accordance with EN 2078. Product shall satisfy the requirements of the material standard and/or order and shall be free from irregularities prejudicial to the subsequent manufacture or use of this product. Not wit
25、h standing previous acceptance complying with this material standard, any product that is found, at a later stage, to contain such defects shall be rejected. Unless otherwise specified, the requirements in Tables 1 and 2 shall apply in conjunction with those of the relevant material standard. Table
26、1 relates to lines 1 to 29 (inclusive) of the material standard and Table 2 relates to lines 30 onwards in which the sub-line format is also used. Lines 2 to 98 may also be opened in line 100 if the material standard details specific qualification requirements. If a specific line number is not shown
27、 in Tables 1 and 2, the requirement is stated in the material standard and/or order. The requirements of the order and/or material standard shall over-ride the requirements of the technical specification. 6.2 Qualification requirements Qualification requirements when invoked by the material standard
28、 and/or order are detailed in Tables 1 and 2. Unless otherwise agreed between the manufacturer and purchaser the qualification phase shall be run on the first 3 batches, coming from 3 different ingots. 6.3 Release requirements 6.3.1 Release tests Release testing shall be the responsibility of the ma
29、nufacturer. The purchaser reserves the right to perform any of the inspections and/or tests required by the material standard and/or order. prEN 4800-003:2009 (E) 6 The test samples shall be representative of the product. When required the manufacturer shall inform the purchaser of the planned dates
30、 for extraction of samples and release testing in order that these operations may be witnessed. Tables 1 and 2 detail the requirements for each line of the material standard. Unless otherwise specifically requested by the purchaser, a particular inspection and/or test for release shall be carried ou
31、t if corresponding acceptance criteria and/or values are stated in the applicable material standard, but see also in 6.3.5. 6.3.2 Retests If the test procedure or test piece preparation is faulty, testing shall be re-applied at the original frequency after rectification of the original cause of fail
32、ure. When failure cannot be attributed to faulty testing, or test piece preparation, further test samples shall be selected at twice the original frequency from the product, one of which shall be that on which the original results were obtained unless already withdrawn by the manufacturer after suit
33、able identification of the cause of failure. If all retest results are satisfactory, the batch shall be accepted. If one or more tests are unsatisfactory, the batch shall be: rejected, or 100 % retested and the conforming products accepted, or partially or fully re-heat treated if heat treatment can
34、 rectify the cause of the failure and tested as a completely new batch except for chemical composition, for which redetermination of hydrogen content is required. No product or test sample shall be re-heat treated more than twice 6.3.3 Rejection Any failure to meet the requirements of the material s
35、tandard shall be cause for rejection. 6.3.4 Special tests Special tests may be required by the purchaser. In such cases, the nature of the test, method, frequency and technical requirements shall be specified on the order or inspection schedule and shall be mutually agreed by the manufacturer and pu
36、rchaser. 6.3.5 Capability clause Where capability clause is invoked and where sufficient statistical evidence exists, the test shall not be carried out (unless specifically requested by the purchaser). However, this in no way reduces the obligations of the manufacturer to fulfil the requirements. If
37、 subsequent testing indicates that the product does not comply with the requirements, the batch shall be rejected. If sufficient statistical evidence does not exist, the test shall be carried out at a frequency agreed between the manufacturer and the purchaser. 6.3.6 Statistical process control Redu
38、ction in the extent of release testing, other than that defined in 6.3.5 above, may be negotiated with the purchaser on the basis of appropriate statistical process control and/or statistical data. prEN 4800-003:2009 (E) 7 6.3.7 Inspection and test report The manufacturer shall furnish, with each de
39、livery, a report conforming to the requirements of EN 2078 stating the following: manufacturers name and address and, if appropriate, identification of the plant; order number; material standard number; delivery condition and metallurgical code of the product; quantity and dimensions; manufacturing
40、and inspection schedule reference; cast and batch number; batch and/or test samples heat treatment condition; results of the tests and retests if any. 6.4 Traceability Each product shall be traceable to the cast, production batch and/or heat treatment batch at all stages of manufacture, testing and
41、delivery. prEN 4800-003:2009 (E) 8 Table 1 Technical requirements for lines 1 to 29, where appropriate Frequency of testing Material standard line reference No Title Requirements Qualification Release 1 Material designation See EN 2032-1. The test samples used for chemical analysis shall be represen
42、tative of the product and shall be taken from location corresponding to top and bottom of each ingot produced after the final melting stage. The method of chemical analysis shall be at the discretion of the manufacturer unless otherwise stated in the material standard or order. In cases of dispute,
43、the method of chemical analysis shall be agreed between the manufacturer and purchaser preferably using existing chemical analysis standards. The measured chemical composition shall be stated on the inspection certificate. 2 per cast 2 per cast 2 Chemical composition Specific requirements for hydrog
44、en content: The hydrogen content shall be determined on each batch in the delivery condition in accordance with EN 3976. 1 per batch 1 per batch 3 Method of melting Method of melting consists of multiple melt using combination of non-consumable electrode, consumable electrode and cold hearth (electr
45、on beam or plasma arc) melting practices. Some of the following requirements are dependent on the actual melting route non-consumable electrode melting should be used for consolidation purpose only. 1 Raw material: Raw materials shall be purchased only from suppliers approved by the manufacturer and
46、 registered in his list of approved suppliers. Approval of suppliers shall be made in accordance with written procedures contained within the quality assurance system of the manufacturer. Titanium sponge and alloying elements: The requirements shall be specified by the manufacturer who shall also es
47、tablish the following procedures for the evaluation and acceptance testing of each batch. titanium sponge: manufacturing method, level of impurities, particle size, freedom from surface contamination ; alloying elements: chemical composition including level of impurities, particle size, freedom from
48、 foreign particles. continued prEN 4800-003:2009(E)9Table 1 Technical requirements for lines 1 to 29, where appropriate (continued) Frequency of testing Material standard line reference No Title Requirements Qualification Release Recycling of scrap: See EN 2955. The categories and sub-categories of
49、scrap which may be used by the manufacturer are given in the following table. Scrap categories and sub-categories (see EN 2955)Melting method which includes cold hearth VAR-only melt method 1 allowed allowed 2 allowed allowed 3 allowed allowed 4.1 allowed aallowed a4.2.1 allowed a ballowed a4.2.2 allowed a bnot allowed a4.3.1 allowed a ballowed a 4.3.2 allowed a bnot allowed a5.1 allowed allowed 5.2 not allow
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1